Ttl serial

Features: 1, Use original chip CP2102, generate COM port after installing the driver. 2, The standard input MICRO MINI-USB cable connected to the computer USB interface, with 3.3V and 5V two power output 3, With a resettable fuse. In the event of accidental short-circuit can effectively protect your device and computer USB port to download 4, On-board status indicators, receiving indicator properly installed drive status indicator remains, send and receive indicator flashes when the communication with run LED indicator. 5, Supports baud rates from 300bps ~ 1Mbps between 6, The communication format support: (1) data bits 5, 6, 7, 8. (2) support 1.5, 2 stop bits. (3) odd, even, mark, space, none parity 7, Supported operating systems: windows 8.1 / 7 / vista / XP / 98, Mac OS-X / OS-9, Linux 8, USB seat MICRO MINI-USB interface block 9, With DTR trigger signal output can be directly arduino pro mini ATMEGA328P and other Arduino board download traffic. 10, Module size: 15.7mm * 21.2mm super small. Specifications: 1. Embedded USB transceiver, no external circuit device 2. Containing clock circuit, no external circuit device 3. Contains power-on reset circuit The on-chip voltage regulator within the 3.3V output 5. Meet the USB2.0 specification requirements 6. SUSPEND pins support USB suspend state 7. Asynchronous serial data bus compatible with all handshakes and modulation controller interface signals 8. Support data format is 8 data bits, 1 stop bit and the parity bit 9. Connotation 512 byte receive buffer and 512 byte transmit buffer 10. Supports hardware or X-ON / X-OFF Hand

USB to TTL UART CP2102 là module chuyển đổi tín hiệu USB sang tín hiệu Serial tuần tự theo chuẩn TTL. Mạch sử dụng chip CP2102 CP2102 là chip USB to UART của Silabs. CP2102 có kích thước nhỏ gọn và yêu cầu rất ít thành phần bên ngoài để hoạt động được ngay. CP2102 không sử dụng thạch anh ngoài như các chip PL2303. Module có sẵn ngõ ra điện áp 3.3V với dòng tải tối đa là 100mA. Trên mạch có 5 cổng đầu ra: 3.3V RST 5V Tx Rx Gnd. Trong đó chân RST được sử dụng để ngắt kết nối USB của module với máy tính. Chân RST có thể được chỉnh sửa để trở thành chân RESET dùng để nạp chương trình cho Arduino pro mini mà không cần phải nhấn nút

Module Serial MP3 Music Player UART TTL là mạch chơi âm thanh MP3 từ thẻ microSD cực kì nhỏ gọn mà còn tích hợp sẵn ampli để có thể kết nối với loa. Ngoài ra, ta còn có thể điều khiển chơi MP3 bằng Arduino. Module hỗ trợ giải mã MP3, WAV THÔNG SỐ MODULE SERIAL MP3 MUSIC PLAYER - Tốc độ lấy mẫu tần số (kHz): 8 / 11,025 / 12/16 / 22,05 / 24/32 / 44.1 / 48 - Định dạng: MP3 / WAV - Hỗ trợ thẻ nhớ Micro SD, thẻ Micro SDHC - Tốc độ truyền mặc định là 9600bps - Có thể giao thếp UART TTL để điều khiển - Có thể chỉnh 30 mức âm lượng - Điện áp: 3.2-5.2VDC - Kích thước : 43mm x 25mm ----------- Code tham khảo: https://drive.google.com/file/d/1YI_1NQmKGoAZeVp6eol2u9N1R7O6gwDs

Thời gian giao hàng dự kiến cho sản phẩm này là từ 7-9 ngày Mô tả Sản phẩm: 1. Chip chính là CP2102, tạo ra cổng nối tiếp ảo sau khi cài đặt trình điều khiển. 2. USB nối nguồn, đầu cắm bao gồm 3,3V (<40mA), 5V, GND, TX, RX, mức tín hiệu là 3,3V, cực dương. 3. Đèn báo trạng thái trên bo mạch và đèn chỉ báo thu phát, sau khi lắp đặt đúng cách, đèn chỉ báo trạng thái sẽ luôn sáng, đèn chỉ báo thu phát sẽ nhấp nháy, và tốc độ truyền càng cao, độ sáng càng thấp. 4. Hỗ trợ tốc độ truyền từ 300 bps đến 1 Mbps 5. Hỗ trợ định dạng: 1) 5,6,7,8 bits; 2) 1,1.5,2 stop bits; 3) lẻ, chẵn, đánh dấu, không gian, không kiểm tra 6. Hỗ trợ các hệ điều hành: WIN7 / WIN8 / vista / xp / server 2003/200, Mac OS-X / OS-9, Linux 7. Đầu USB có thể kết nối trực tiếp với cổng USB của máy tính. 8. Quy trình SMT được sử dụng để sản xuất các thành phần dán với chất lượng ổn định. Chúng tôi kinh doanh bán sỉ và bán lẻ liên lạc với chúng tôi nếu cần Skype: winniecai11 Whatsapp +86 13725560553 #CP2102 #PL2303 #UART

Product Features: With the original FT232BL industrial grade chip, the external EEPRON (93C46) is more stable Support for Windows 10 Support 3 kinds of power supply modes: 5V external power supply; 3.3V external power supply; external power supply (required 3.3V-5V) With 3 LEDs: TXD LED, RXD LED, POWER LED GND, RXD, TXD, 3V3, 5V: use curved pin to lead out The remaining function PIN: reserved pad CTS, RTS With 500MA self-recovery fuse reversed does not burn Applications: RS-232 legacy device upgrade to USB USB to RS-232 serial adapter #FT232 #FT232BL #USB #TTL #Upgrade #Download #Brush #

Series: STC Downloader Model: CP2102 module Type: Other IC Power: W Usage: USB to TTL Package: CP2102 module Optional service: Floor up brush board Application area: 3C digital Product Description: Online Download Item No .: C

It works great for programming microcontrollers such for Arduino, boarduino, Bareduino, Raspberry Pi, ESP8266, Mini minimOSD, and Atmel Xmega Xplained, Atmega328 mini pro, or any other that can be programmed over serial After installing the driver,This FTDI TTL adapter will simulate a COM port on your computer/laptop. Through this simulated COM port, you can communicate or program with various hardware or MCUs, such for Arduino board, Raspberry Pi, ESP8266, router and so on. Main chip: FTDI FT232BL Pin Definition: CTS,RTS,RXD,TXD,GND,VCC Output VCC: 3.3V or 5V USB interface: 2.0 With 500MA self-recovery fuse reversed does protection The maximum speed: 921600bps List of supported systems Windows xp,7,8,10 Ubuntu 11.10, kernel 3.0.0-19 Mac OS X 10.3 to 10.8 (32 &64 bit) Mac OS X 10.9 and above(64 bit) Instructions for use:(Example MCU) GND: Connect to GND RXD: Connect to MCU.TX (Signal Flow: MCU.TX Greater than Greater than FT232 Greater than Greater than PC.RX) TXD: Connect to MCU.RX (Signal Flow: MCU.RX Less than Less than FT232 Less than Less than PC.TX) 3V3/5V: Output 3.3V or 5V (ule powered by USB, jumper cap :to 3.3V or 5V) RTS: Connect to MCU.CTS (Signal Flow Direction: MCU.CTS Less than Less than FT232 Less than Less than PC.RTS) CTS: Connect to MCU.RTS (Signal Flow: MCU.RTS Greater than Greater than FT232 Greater than Greater than PC.CTS) Material:plastic colour:Black+gold Package Contents: 1 x Adapter ule 1 x 5Pin Dupont Line(Note: Random color, don't accept the specified color.)Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

Brand: 🐟———————————————————— Grade: Notes The sticker time is 4:00 p.m. (Beyond 4 Points, all days handled) Every day from Monday to Sunday. (~~national holidays) Get off the order during the period, extend until the end of the working hours to handle the mishap Please read carefully before subscribing、 related contents such as color (There was a slight error in the measurement of the gnawing, please forgive me)。 To avoid excessive size of the package unavailable, we set a sales limit. If you need to buy more, please contact us about the quantity restriction. Yes 【Commodities】 Anything like that, welcome to 【Talking】 Selling the shopkeeper. Please select the correct address/piece market before subscription. Changes to address/mall after establishment, please 【Before seller application number】, cancel the bid (The seller's backstage briefly dissuaded from supporting the modification of the berries)。 Status: 【In process】 Parcel has been arranged for disposal, whether please have the mailed out beforehand. Unusual when received, please send photos to chat, the clerk will handle it for you as soon as possible. Please do not 【Being eager to criticize without communicating】 Bring us all a lot of madness Within 7 days of the parcel reaching the store, buyers need to pick up their pieces in time (In case of inconvenience, family and friends may be asked to replace them)。 【Market turns】 Solutionsa: Within 48 hours, placement of male male or female males will be pushed backstage in a (Station Internal Letter) The buyer is in the pn in the new marketplace. If a delivery fails (: The addressee is not at home、 telephone answers, etc.), will return to the temporary do

We have many products in our warehouse, our warehouse is in Shenzhen . Genaral it need 1-2weeks arrive your hand. if you subimit order , we will handle in 1-3days.if you chat with us , we donot reply you, donot worry , we are try to handle your order.so pls donot cancel o

Sorry for the inconvenience, i am sorry for you donot receive goods. i have shiped goods , but recently all world now has epidemic , most company move slowly , can you wait a week , if you still not receive , i can resend or full refund . if you donot want wait , i can refund now . sorry

Material: Plastic, metal RS232 Serial TO TTL Converter ule This is small RS232 to TTL level serial converter ule, suitable for any 3.3v or 5v target devices. Built-in SP3232EEN chip Fully compatible with existing legacy COM port software Easy to use Output signals: VDD, TXD, RXD, CTS, RTS, GND Power input: 3.3V or 5V Compact design. Package Includes: 1 x RS232 Serial TO TTL Converter ule 4 x Jumper Wire Note: Random color, don't accept the specified color. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

We have many products in our warehouse, our warehouse is in Shenzhen . Genaral it need 1-2weeks arrive your hand. if you subimit order , we will handle in 1-3days.if you chat with us , we donot reply you, donot worry , we are try to handle your order.so pls donot cancel o

WEMOS CH340G CH340 Breakout 5V 3.3V Micro USB to TTL Serial Module For Arduino Downloader Pro Mini We deal in wholesale and retail Feel free to contact us #WEMOS #CH340G #CH340 #Breakout #5V #3.3V #Micro #USB #to #serial

We have many products in our warehouse, our warehouse is in Shenzhen . Genaral it need 1-2weeks arrive your hand. if you subimit order , we will handle in 1-3days.if you chat with us , we donot reply you, donot worry , we are try to handle your order.so pls donot cancel o

Tips: This module can realize the mutual conversion between TTL signal and RS485 signal, but 485 is half-duplex communication. This communication mode can realize two-way communication, but it can not be carried out in two directions at the same time. That is, each end of the communication channel may be the transmitting side or the receiving side, but at the same time, the information may have only one transmission direction. This module realizes the mutual conversion between TTL signal and RS485 signal, no need to "receive - send" control, use this module as you operate the serial port as simple, compatible with 3.3V and 5.0V power supply, compatible with 3.3V and 5.0V signal; Imported chip, the performance is very stable, to industrial design standards; anti-interference ability, while more effective 485 mine design, in the industrial field and field harsh environment, the transmission distance of up to 1000 meters Of the 850 meters of 2 * 1.5 cable to do the test, it is recommended to use within 800 meters, more than 800 meters, please add repeaters). Product Features: Fully consider the 485 bus lightning protection design and anti-jamming design, long-distance transmission in the field, the module's "earth" side access to the earth, can play a very good anti-jamming and lightning effect, 485 Bus more secure; indoor short distance transmission can not access the earth. The use of standard 2.54 pitch design, to facilitate your secondary development. With 120 ohm matching resistor, shorted R0 to enable matching resistor, long-distance transmission of the proposed short-circuit. Support multi-machine communication, allowing access to up to 128 devices on the bus. Support hot-swappable, there will not be other 485 chip hot plug signal plug dead phenomenon. Large area of copper, to prevent signal interference. Half-hole process design, thickness 0.8mm, can be easily used as a mother board, but also welding terminal use. With RXD, TXD signal indicator. Product parameters: Operating voltage: compatible with 3.3V and 5.0V Support baud rate: 110-256000bps Operating temperature: -40 Celsius to +85 Celsius Communication signal: compatible with 3.3V and

Module USB to TTL UART Serial PL2303 có dây Giới thiệu: Cáp chuyển USB UART PL2303 được sử dụng để chuyển giao tiếp từ USB sang UART và ngược lại thông qua cổng COM trên máy tính, cáp sử dụng IC giá rẻ PL2303 nên có chi phí thấp, đầu ra UART chuẩn Header cái Female dễ dàng kết nối và sử dụng. Thông số kỹ thuật: Điện áp sử dụng: 5VDC (cấp từ cổng USB). IC chính: PL2303. Đầu ra: UART(female). Chiều dài: 1m. Hỗ trợ một số các hệ điều hành cũ Win XP, Win7,Linux,..., không sử dụng được với các hệ điều hành mới như Win 8, Wi

We have many products in our warehouse, our warehouse is in Shenzhen . Genaral it need 1-2weeks arrive your hand. if you subimit order , we will handle in 1-3days.if you chat with us , we donot reply you, donot worry , we are try to handle your order.so pls donot cancel o

Mạch USB to TTL Serial PL2303HX USB to TTL Serial PL2303HX sử dụng IC chuyển đổi USB to COM PL2303HX với nhiều cải tiến về hiệu năng của hãng Prolific. Module USB to TTL Serial PL2303HX có sẵn các thành phần cần thiết, bạn chỉ cần cắm vào cổng USB của máy tính là có ngay 1 cổng COM ở mức 5V có thể giao tiếp với vi điều khiển. Module USB to TTL Serial có 3 LED gồm 1 LED nguồn, 1 LED báo tín hiệu Tx và 1 LED báo tín hiệu Rx. Thứ tự các chân trên module USB to TTL Serial PL2303HX: Chân Module PL2303HX Chân vi điều khiển Gnd Gnd Tx Rx Rx Tx 5V Vcc 3.3V Module PL2303HX đã có sẵn đầu ra 3.3V giành cho các IC điện áp thấp Đối với hệ điều hành MAC OS và Linux, bạn không cần tải driver, driver cho 2 hệ điều hành này đã được biên dịch và kèm theo. Với Windows, bạn nhấn vào liên kết bên dưới để tải về driver. Chú ý: Mạch không tương thích với Windows 8/10. Các bạn làm theo hướng dẫn này để cài driver trên Win 8/10 nhé: https://dientuhte.com/huong-dan-cai-driver-pl2303hx-rev-a-voi-win

Features: Support devices with RS485 interface: surveillance cameras, video capture device, fingerprint attendance machine, PBX, CNC machine, microcontroller, etc. Specifications: Standard: USB2.0 standard, backward compatible, in line with the standard RS485 Direction control: the use of automatic data flow control, auto distinguish and control data transfer direction Baud rate:300-9216000bps, automatically detecting the serial signal data rate Load capacity: support multipoint, each converter allows RS485 interface device to connect 32 Interface Protection: TVS tube protection, USB self-recovery protection Support Windows98/ME/2000/XP/WIN7/Vista, Linux, Mac Color: green Size: 75*18*14mm Net weight: 15 g New products, industrial grade USB to 485 modules, 485 chips to facilitate the replacement for the 485 chip hardware debug easy to burn out the case easier to use. Package Include: 1* USB to TTL/RS485 Converter Adapter Module #USB 2.0 to TTL RS485 Serial Converter Adapter FTDI FT232RL SN75176 double function double prote

Kích đèn flash godox X2T TTL Godox X2T-C Dùng cho máy ảnh canon Godox X2T-N Dùng cho máy ảnh nikon Godox X2T-S Dùng cho máy ảnh Sony Bảo hành 12 tháng Trigger Wireless Flash Godox X2T là sự kết hợp giữa tính năng thu và phát được tích hợp sẵn trong đèn hay các bộ nhận của Godox. Bộ kích sóng Godox X2T sử dụng cho các sản phẩm godox được tích hợp tần sóng 2,4 GHz. Bộ kích sóng Godox X2T có thể kích được một hoặc nhiều đèn Flash trong 5 nhóm, 32 kênh và cài đặt ID để tránh nhiễu từ các hệ thống Godox khác gần đó. ĐIỂM NỔI BẬT CỦA SẢN PHẨM Bộ kích hoạt không dây, hoạt động ở tần số 2,4 GHz, là sự kết hợp giữa máy phát và máy thu có thể bắn nhiều bộ đèn flash trong 32 kênh và 99 cài đặt ID, do đó không có nhiễu từ các hệ thống gần đó. Bạn có thể điều khiển các chức năng flash như chế độ flash, đầu ra nguồn, đèn mô hình hóa, đồng bộ tốc độ cao là 1/8000 giây và tiếng bíp có thể nghe được của đèn flash Godox trong khi vận hành các đèn flash trong phạm vi không dây lên tới 328 '. Chức năng cài đặt quét tích hợp có thể giúp bạn tự động định vị kênh ID với ít nhiễu nhất. Tất cả các cài đặt được xem dễ dàng trên màn hình LCD lớn của trình kích hoạt, có thể được chiếu sáng ngược cùng với các nút nhóm và chức năng. Cổng USB Type-C được đặt ở phía bên của trình kích hoạt không dây để tải xuống các bản cập nhật chương trình cơ sở như là ổ cắm đồng bộ 3,5mm để kết nối đèn flash không phải là TTL hoặc bắn camera qua dây camera từ xa. Ứng dụng GodoxPhoto có thể tải xuống tương thích với điện thoại thông minh hoặc máy tính bảng iPhone hoặc Android trong khi vận hành các kích hoạt thông qua Bluetooth. Khóa nhanh giày nóng đảm bảo kích hoạt không dây an toàn trên giày nóng của máy ảnh. Triger Godox X2T sử dụng cho Canon Chế độ nhóm GR - A / B / C / D / E (5 nhóm) / 32 Kênh Sử dụng ứng dụng GodoxPhoto để sử dụng cho các dòng Smartphone thông qua Bluetooth Hệ thống Radio Godox 2.4GHz Phạm vi sóng- 100m + Chế độ Flash - ETTL / M / OFF Đồng bộ HSS đến 1/8000s Tốc độ đồng bộ hóa: 1/256 giây (Bình thường) Đèn hỗ trợ AF (với công tắc Bật / Tắt) Cổng USB: Type-C để Nâng cấp Firmware Kích thước : 72 x 70 x 58 mm Cân nặng : 90 Gr #kichgodoxX2t #kichdenflashgodox #kic

We have many products in our warehouse, our warehouse is in Shenzhen . Genaral it need 1-2weeks arrive your hand. if you subimit order , we will handle in 1-3days.if you chat with us , we donot reply you, donot worry , we are try to handle your order.so pls donot cancel o

We have many products in our warehouse, our warehouse is in Shenzhen . Genaral it need 1-2weeks arrive your hand. if you subimit order , we will handle in 1-3days.if you chat with us , we donot reply you, donot worry , we are try to handle your order.so pls donot cancel o

Product Features: Using FT232BL industrial chip, external EEPRON (93C46) more stable Support for Windows 10 Support three power supply mode: 5V external power supply; 3.3V external power supply; by the external power supply (requires 3.3V-5V) With three LED: TXD LED, RXD LED, POWER LED GND, RXD, TXD, 3V3, 5V: Cited with curved needle Other functions PIN: Reserved pad CTS, RTS With 500MA self-recovery fuse reverse does not burn Applications: RS-232 traditional device upgrade to USB USB to RS-232 serial adapter Instructions for use: (access MCU as an example) GND: Connect to GND RXD: connected to MCU.TX (signal flow: MCU.TX >> FT232 >> PC.RX) TXD: connected to MCU.RX (signal flow: MCU.RX << FT232 << PC.TX) 3V3 / 5V: output 3.3V or 5V (module powered by USB, jump to jumper cap to 3.3V or 5V) RTS: Connect to MCU.CTS (signal flow: MCU.CTS << FT232 << PC.RTS) CTS: then MCU.RTS (signal flow: MCU.RTS >> FT232 >> PC.CTS) Package included: 1*FT232 FT232BL FT232RL USB to Serial USB to TTL Upgrade Download Brush Board Gold Note:The color of the cable is r

TTL to MBUS main ule, serial port to MBUS main ule, used in water, gas, heat and meter MBUS meter reading ule, input wide voltage range of 5V-15V, compatible with a variety of TTL levels, TTL level can be set, the bus belt short-circuit protection, the cancellation of short-circuit can be self-recovery, short circuit protection state ultra-low power consumption. The ule is compatible with a variety of TTL levels, and can be flexibly applied in wireless RF to MBUS ule, GPRS to MBUS, 485 to MBUS and other ules. The ule is exported to Europe, the Middle East and other regions, and is often used in wireless RF to MBUS, GPRS to MBUS, 485 to MBUS and other applications. 1, compatible with 3.3V, 5VTTL level, level voltage can be set! 2, the bus output short circuit protection, short circuit state indicator output, the bus short circuit self-recovery! 3. Meet MBUS international standards and international standards! 4, small size, low space cost, easy to install! 5. Complete shielding system, stable and reliable communication, good EMC! 6, communication baud rate 300-9600 can be adapted! Cooperate with this shop from the machine ule limit communication baud rate up to 38400 no error! 7. No self-collecting data communication within the rated load range! 8, according to the countless spontaneous from the phenomenon! 9. Provide standard 2.54mm spacing row holes! Provides bus voltages within the range of MBUS standards. The following is a description of the MBUS standards Note: after short circuit of the ule, the bus is automatically shut off. The bus has ultra-low power consumption. The ule automatically detects whether the bus is short circuit and can be restored automatically! colour:green Material:plastic size:51x27mm Package Contents: 1 x TTL to MBUS main ule Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

Material: Plastic, metal RS232 Serial TO TTL Converter ule This is small RS232 to TTL level serial converter ule, suitable for any 3.3v or 5v target devices. Built-in SP3232EEN chip Fully compatible with existing legacy COM port software Easy to use Output signals: VDD, TXD, RXD, CTS, RTS, GND Power input: 3.3V or 5V Compact design. Package Includes: 1 x RS232 Serial TO TTL Converter ule 4 x Jumper Wire Note: Random color, don't accept the specified color. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

Module USB to TTL UART Serial PL2303 có dây (loại tốt, màu xanh) Giới thiệu: Cáp chuyển đổi tín hiệu TTL UART Serial RS232 PL2303 chuyển đổi tín hiệu từ công USB sang TTL UART. Thông số kỹ thuật: Chíp xử lý: PL2303TA . Chuẩn giao tiếp: USB-A. Tốc độ truyền dữ liệu: 115200 Nguồn cung cấp: 5V/3.3V. Chi tiết chân: (Tx / Rx / Pwr / G

<div><p>Item size: 4.3 * 1.6 * 0.7cm Operating voltage: 3.3V Item weight: 3g Signal coverage: 30ft Compatible with bluetooth master module".slave module"or master-slave(whole) module. Package Included: 1PC*HC-06 bluetooth module Package size: 9 * 3 * 1cm Bluetooth version: V2.0+EDR With VCC.GND.TXD.RXD foot for the Bluetooth With "Re-seach" button(ON/OFF/WAKE foot for it , external MCU outinput "High level" can control module to re-seach) With LED indicator light, use 150mA and 3.3V regulation chip. Input voltage: 3.3~6V Commercial Series: Bluetooth module board Series Package weight: 8g Default Baud Rate: 9600,8,1,n. Note: input power supply 3.3~6V, Prohibit more than 7V No "Automatically prevent power supply peversing func", so please correctly connect power supply We advise to install "Bluetooth master module" The "State" is output foot for LED status, when bluetooth "Unconnected", output "Pulse" ; when bluetooth "connected", output "High level", we can determine the states from "MCU" If only the board , No any "Bluetooth Function "</p><

Adopt for ftdi ft232rl chip. Take out all ft232rl chip signal ports, ttl / cmos level. With rxd / txd transceiver communication indicator. USB powered, optional 5v or 3.3v level interface. High quality material: more durable and serve longer. Material:ABS colour:Blue Package Contents: 1 x uleOnly the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

RXD/TXD transceiver communication indicator, with 500MA self-restore Fuse Pin Definition: DTR, RXD, TX, VCC, CTS, GND Compatible with Linux operating system and is widely popular among Linux users. No additional drivers are required to run the FTDI USB to TTL Converter Adapter Working Voltage: 3.3V/5.5V Pitch: 2.54mm Colour:red Material: PCB Size:36 x 17.5mm Package Contents: 2x Adapter ule Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

1, the original chip CP2102, generate COM port after installing the driver. 2, then the standard input MICRO MINI-USB cable connected to the computer USB interface, with 3.3V and 5V two power output 3, with a resettable fuse. In the event of accidental short-circuit can effectively protect your device and computer USB port to download 4, on-board status indicators, receiving indicator properly installed drive status indicator remains, send and receive indicator flashes when the communication with run LED indicator. 5, supports baud rates from 300bps ~ 1Mbps between 6, the communication format support: 1) data bits 5,6,7,8; 2) support 1.5, 2 stop bits; 3) odd, even, mark, space, none parity 7, supported operating systems: windows 8.1 / 7 / vista / xp / 98, Mac OS-X / OS-9, Linux 8, USB seat MICRO MINI-USB interface Block 9, chip components for the regular company of welding, stable quality, beautiful appearance 10 with DTR trigger signal output can be directly arduino pro mini ATMEGA328P and other Arduino board download traffic. 11, module size: 16mm * 20mm super small. Features: 1. embedded USB transceiver, no external circuit device 2. containing clock circuit, no external circuit device 3. contains power-on reset circuit The on-chip voltage regulator within the 3.3V output 5. Meet the USB2.0 specification requirements 6.SUSPEND pins support USB suspend state 7. asynchronous serial data bus compatible with all handshakes and modulation controller interface signals 8. Support data format is 8 data bits, 1 stop bit and the parity bit 9. connotation 512 byte receive buffer and 512 byte transmit buffer 10. Supports hardware or X-ON / X-OFF Handshake How to install the driver win7 / win8 1, first open the package, like the way next, remember installation directory 2, according to the following method to start the service 3. Locate the driver in Device Manager, select Update Driver, browse my computer for driver, select the directory just installed, determine waiting like win8.1 Right update drivers automatically find the drivers, it will prompt the driving data is invalid, in fact, the problem often encountered in windows8, the drive is no problem, the beginning has been installed on, and later discovered may be a hardware incompatibility. If you are using Windows8 or windows 8.1, but is non-genuine ghost or other systems, and uses a variety of optimization tools Streamlining system, then in the process of installing the driver, you may encounter the "Data invalid" wrong "Invalid Data" solutions are as follows: 1, press Winkey + R on the keyboard, the pop-up "Run" dialog, enter "services.msc", also by under "Computer Management" window, find the "service"; 2, found in the list of services "Device Install Service" and "Device Setup Manager" two service items, make sure these two services is turned on, if not open, you can click the left side of the "Start" service. Package Included: 1 x CP2102 M