Tap 50004

Thời gian giao hàng dự kiến cho sản phẩm này là từ 7-9 ngày Đặc trưng: Pin lithium sắt phốt phát TP5000 dòng điện 4.2/3.6V có thể được chuyển đổi Phiên bản 2A là phiên bản hiệu năng cao nhất của TP5000, do dòng điện lớn hơn nên nhiệt lượng sẽ tương đối lớn nhưng tốc độ sạc nhanh nhất Thông tin sản phẩm: Đầu vào: 4.5-9V (không thể quá 9v, phù hợp 5v ~ 6v) Điện áp: 4.2V / 3.6V; dung sai ± 1% (bảng mạch mặc định 3.6V) Dòng điện: 2A (thay đổi điện trở lấy mẫu có thể được điều chỉnh, công thức là: 0.1 v / dòng điện = điện trở) Công dụng: Sạc pin lithium hoặc pin lithium sắt phốt phát, sạc đầy, quá trình sạc sẽ dừng lại, đèn LED màu xanh lá cây sáng lên Đèn báo trạng thái chưa hàn và người dùng bắt buộc phải tự hàn Kích thước: 2.6x1.8cm / 1.02x0.71 inch Lưu ý: Xin vui lòng cho phép sai số 1-3mm do đo lường thủ công. Hãy đảm bảo rằng bạn không phiền lòng về điều này trước khi đặt hàng. Do sự khác biệt giữa các màn hình khác nhau, hình ảnh có thể không phản ánh màu sắc thực tế của sản phẩm. Xin cảm ơn! Gói hàng bao gồm: 1 x Bảng mạch sạc pin T

Features: Switch buck mode has higher efficiency and fever than linear charging circuit. Charging current 1A, in constant current charge to maintain 1A. No additional heat dissipation is needed, which reduces the influence of heating on charging current. Reduce charging time. Ordinary lithium-ion lithium polymer batteries or lithium iron phosphate batteries can be selected. Only one jumper is needed to change the settings. Specifications: Material: ABS Size: 21.5*14.5*4.2mm/0.85*0.57*0.17" Input: 4.5-9V Output voltage: 4.2V/3.6V±1% (PCB default lithium-ion battery 4.2V) Output current: default 1A Usage: 1. Lithium batteries only need to be connected with 5V power supply and output B+B-to be connected with batteries. In charging, the red light is on, the charge is full and the green light is on after charging. 2. For lithium iron phosphate batteries of 3.6V, only soldering iron is needed to open the tin spot between the two soldering pads. The connection method of the power battery is unchanged as described above. If it is necessary to recharge 4.2V lithium batteries, the solder pad can be dipped and soldered to connect the batteries. Notes: 1. Due to the different monitor and light effect, the actual color of the item might be slightly different from the color showed on the pictures. Thank you! 2. Please allow 1-3mm measuring deviation due to manual measurement. Included: 1 XBattery Charging

Estimated delivery time for this product is 7-9 days Tp5100 Lithium Battery Charger Circuit 2 single 2a 18650 4.2V 8.4V dedicated battery board Product specifications Size: 25 * 17 * 5mm super small size Input voltage: 5-18V DC source Charging status: green light full and no load, red while charging The voltage setting should be operated in the power off state. When a switch is installed, the input is disconnected and then switched. Can also be used for white LED drive current: set up a single lithium drive, set up a dual-chain dual drive Description: The TP5100 is a 8.4V dual buck switch, one cell 4. The chip manages a 2V lithium battery charge. The QFN16 package is super compact and the external circuit is simple, making the TP5100 ideal for handsets, very large current charge management applications. Meanwhile, TP5100 integrates overcurrent, low voltage protection, over temperature protection, short circuit protection, battery temperature monitoring, battery reverse protection. TP5100 has a wide input voltage 5V-18V, dual battery charge to pre-charge, constant current, three-phase constant voltage, pre-charge drip current through an external resistor adjustment, maximum charge current up to 2A. TP5100 with 400kHz mode switching frequency allows for smaller external Suo device use and large current charge maintains smaller amount of heat. TP51OO integrates power PMOSFE, anti-intrusion circuit, so there is no intrusion protection and other external Schottky diodes. Characteristics: - Lithium 8.4v / 4.2v double charger - Programmable charging current. 0. 1A-2A Stable programming with current deposit 10% -100%. Wide operating voltage, reaching maximum I8V Red and blue LED charging status indicator lights Chip temperature protection, over current protection, low voltage protection Battery temperature protection, reverse battery shutdown, short circuit protection Switching frequency 400Khz, inductance can use 20uH or more - PWR_ON pin for switch control Maximum levels: Static input supply voltage (VlN): 20V - BAI: -8,4V-20V - BAT short circuit duration: Continuous - Operating environment Temperature range: -40 ° -85 ° - Storage temperature range: -65 ° - 125 ° Application: - Handheld devices, chargers are different - Smart phone, PDA, cell phone - Player MP4, MP5, tablet - HM - Electric tools - Walkie-talkie Before buying: 1. All goods are available, we will arrange shipment immediately if we get your order. 2. Please read description, if you have any questions, don't hesitate to contact us. After buying: 1.If you are satisfied with our product, please give us 5 star rating. Thank you very much # TP5100 #double #single #lithium #battery #charge #management #compatible # 2A # rechargeable #lithium #plate # 18650 # 4.2V #

Feedback: • Dear buyers, we appreciate your business, if you are satisfied with our service, please leave us a positive feedback. • Please contact us before leaving any negative or neutral feedback. Our aim is to provide Top Level Customer Service, we will work with you to solve any problems. Contact us: • We care about our valued buyers, if you have any questions, our Customer Service staffs will be very glad to help you. We try our best to reply to your emails as soon as possible, however, due to high volume of daily incoming emails and time zone difference, we may not be able to reply your emails immediately. Please allow 24 business hours for us to response. Thank you for your support, I hope everyone has a pleasant business trip in our store, and welcome you to come

Features: 1. Excellent quality: This Charger Module is made with advanced technology and concept. 2. High-quality battery: TP5000 lithium ion battery, 2A current 4 2/3, high quality. 6V can be switched. 3. The charging is fast: 2A version is the ultimate performance version of TP5000, due to the larger current, the heat will- be relatively large, but the fastestcharging speed 4. LED light prompt: lithium battery or lithium iron phosphate battery charging, full charged, the charging will stop, green LED light up, safe and secure. Descriptions: 1. This Charger Module is made with advanced concepts and has a fast charging speed. 2. Excellent quality and durability. Specifications: Input: 4. 5-9V (can not over 9v, suggest 5v~6v) Size: 26*19*6mm Deadline: 4.2V/3 6Ѵ; error t 1% (circuit board default 3.6V) Current: 2A Package Included: 1 x Charger Module Notes: Please allow 0-2mm error due to manual measurement, thanks for understanding. Due to the difference between different monitors, the picture may not reflect the actual color of the item. Please understand, thank

TP5000 lithium ion battery lithium iron phosphate battery 1A current 4.2/3.6V Function: Charge lithium battery and lithium iron phosphate battery. Full of self-stop. Red and green double lights indicate. Size: 21.5*14.5*4.2mm Usage: TP4056 4057 charging board usage is the same.         1. The lithium battery only needs to be connected to the 5V power supply, and the output B+B- can be connected to the battery. The red light is on during charging, and the battery is fully charged. The green light is on after charging.         2, for lithium iron phosphate battery 3.6V, just soldering iron to open the tin point between the two pads. The power battery connection method is unchanged as described above. If you need to change the charge to a 4.2V lithium battery, use the pad to solder it back. Advantages: Switching buck mode, the efficiency is higher than the linear charging circuit, and the heat is much smaller. The charging current is 1A and is maintained at 1A during constant current charging. No additional heat dissipation is required, which reduces the effect of heat on the charging current. Reduce charging time. An optional lithium ion lithium polymer battery or lithium iron phosphate battery can be changed with only one jumper. parameter: Input: 4.5-9V (recommended not to exceed 7V) Output voltage: 4.2V/3.6V plus or minus 1% jumper selection (board default lithium-ion battery 4.2V) Output current: default 1A can be customized 0.5-2A, greater than 1.5A need to add heat    After the efficiency test, it will be described in detail. If the buyer tests the efficiency, it is not recommended to test the battery terminal voltage. Please skip the Rs sampling 0.1 ohm resistance test. In the test, the input power is close to the circuit board, and reducing the length of the connection will have an efficiency test. Impact, it is recommended to increase the capacitance test at the input. The voltage and current test suggests that the current meter with string accuracy is not recommended to read the power supply digital display directly. The current test can be directly connected in series with the positive electrode of the battery. It is only necessary to ensure that the battery is tested below the 3.9V using a large-scale ammeter. We deal in wholesale and retail Feel free to contact us Skype:winniecai11 Whatsapp +86 13725560553 #TP5000 #4.2V #3.6V #1A #Lithium #Battery #Charging #Board #Charger #M

TP5000 DC 4.5v-9v 4.2V/3.6V 1A Lithium Battery Charging Board Lithium Iron Phosphate Charger Power Supply Module Description: 1. PCB size:21.5*14.5*4.2mm 2. Input voltage: DC 4.5-9V(Recommended not to exceed 7V) 3. Output voltage: DC 4.2V/3.6V(default 4.2V) 4. Output current: 1A(Default max) 5. LED Indicator: Charging-Red/Green Flashing,Charged-Green 6. Features:Charging for Lithium battery(4.2V) and Lithium iron phosphate battery(3.6V) 7. Switch mode: 1>. F Welding point ON for Lithium battery and output 4.2V 2>. F Welding point OFF for Lithium iron phosphate battery and output 3.6V 8. Adjust output current(need to modify two resistance value on mark "SANYA"): 1>. Default weld 1pcs R100(0.1ohm) resistor and output 1A(max) 2>. Welding 1pcs 0.2ohm resistor next to R100 and output 1.5A(max) 3>. Welding 1pcs 0.1ohm resistor next to R100 and output 2A(max) 4>. Removed R100 and welding 1pcs 0.2ohm resistor on its place and output 0.5A 5>. It requires additional heat sink if output current more than 1A. Full charged :red light light for a long time. Package includes: 1pcs * TP5000 DC 4.5v-9v 4.2V/3.6V 1A Lithium Battery Charging Board Before purchase: 1. All the goods are in stock and we will dispatch immediately if we receive the order. 2.Please read the item description, if you have any question, do not hesitate to contact us. Shipment： 1.1-2 days to ship(except for the pro-order item) After purchase: 1.If you are satisfied，please give us 5 stars praise. 2.Please contact us before you are going to give us bad review. We are helpful and will solve the problems. if you receive a defect item,please contact us at once with item picture or video #TP5000 #DC #4.5v-9v #4.2V #3.6V #1A #Lithium #Battery #Charging #Board #Lithium #Iron #Phosphate #Charger #Power #Supply #M

-------------------------------------------- Phân Loại Hàng: + Mạch màu xanh : có kèm tản nhiệt + Mạch màu đỏ: không kèm tản nhiệt, giá thành rẻ hơn (trong shop có bán tản nhiệt) -------------------------------------------- Mạch sạc pin Lithium - ion - LiFePO4 4.2 V/3.6v - 1A TP5000 (có kèm tản nhiệt) - LiFePO4 hay còn gọi là pin sắt phốt phát có điện áp định danh 3.65V Thông số kỹ thuật: - PCB kích thước: 21.5*14.5*4.2mm - Điện áp đầu vào: DC 4.5-9 V (Khuyến Cáo không Nên vượt quá 7V) - điện áp đầu ra: DC 4.2 V/3.6 V (mặc định 3.6V sạc pin LifePO4, hàn điểm SET lại để sạc pin Lithium 4.2V) - Dòng sạc: 1A (có thể thay đổi điện trở để sạc lên 2A) - LED Chỉ Thị: Sạc-Red/Màu Xanh Lá Cây Nhấp Nháy, Sạc-Màu Xanh Lá Cây - Có Chip bảo vệ nhiệt độ, bảo vệ quá dòng, bảo vệ điện áp thấp; Lưu ý: Đầu vào không hỗ trợ bảo vệ ngược, vui lòng thêm diot nếu

TP5000 DC 4.5v-9v 4.2V/3.6V 1A Lithium Battery Charging Board Lithium Iron Phosphate Charger Power Supply Module Description: 1. PCB size:21.5*14.5*4.2mm 2. Input voltage: DC 4.5-9V(Recommended not to exceed 7V) 3. Output voltage: DC 4.2V/3.6V(default 4.2V) 4. Output current: 1A(Default max) 5. LED Indicator: Charging-Red/Green Flashing,Charged-Green 6. Features:Charging for Lithium battery(4.2V) and Lithium iron phosphate battery(3.6V) 7. Switch mode: 1>. F Welding point ON for Lithium battery and output 4.2V 2>. F Welding point OFF for Lithium iron phosphate battery and output 3.6V 8. Adjust output current(need to modify two resistance value on mark "SANYA"): 1>. Default weld 1pcs R100(0.1ohm) resistor and output 1A(max) 2>. Welding 1pcs 0.2ohm resistor next to R100 and output 1.5A(max) 3>. Welding 1pcs 0.1ohm resistor next to R100 and output 2A(max) 4>. Removed R100 and welding 1pcs 0.2ohm resistor on its place and output 0.5A 5>. It requires additional heat sink if output current more than 1A. Full charged :red light light for a long time. Package includes: 1pcs * TP5000 DC 4.5v-9v 4.2V/3.6V 1A Lithium Battery Charging Board Before purchase: 1. All the goods are in stock and we will dispatch immediately if we receive the order. 2.Please read the item description, if you have any question, do not hesitate to contact us. Shipment： 1.1-2 days to ship(except for the pro-order item) After purchase: 1.If you are satisfied，please give us 5 stars praise. 2.Please contact us before you are going to give us bad review. We are helpful and will solve the problems. if you receive a defect item,please contact us at once with item picture or video #TP5000 #DC #4.5v-9v #4.2V #3.6V #1A #Lithium #Battery #Charging #Board #Lithium #Iron #Phosphate #Charger #Power #Supply #M

set2: 1 x DC5-24V Sensor Switch + 2 x Charging Board Lithium battery only need to connect a 5V power supply, output B + B-connected battery can be. Charging red light, full of self-stop, charging green light finished. For lithium iron phosphate battery 3.6V, just soldering iron solder between the two solder pad can be. Power supply battery connection method as described above. If you want to change back to charge 4.2V lithium battery, solder pad can be used to solder back. Switch buck e, the efficiency is higher than the linear charging circuit, heat is also much smaller. Charging current 1A, in the constant current full charge to maintain 1A. With overheating protection, overheating will automatically reduce the current to prevent burnout No additional heat dissipation, reducing the impact of heat on the charging current. Reduce the charging time. Optional lithium-ion lithium polymer battery or lithium iron phosphate battery, just a jumper can change the settings. Full version of the use of precious metal ceramic s, X7R temperature characteristics, performance + safety + stability far more than tantalum s! Sensitivity to light : Dark and Light environment. Sensing e: PIR sensing + light control Timer. Sensing Distance: 0.5 Meter to 5 Meter (high temperature will influence switch sensibility). Sensing e: PIR sensing + light control Timer. Charging Board Size: 21.5 x 14.5 x 4.2mm Input: 4.5-9V Output voltage: 4.2V / 3.6V plus or minus 1% (circuit board default lithium-ion battery 4.2V) Output current: default 1A After the efficiency test will be described in detail, if the buyer's own test efficiency, do not recommend testing the battery side voltage, please note that skip the Rs sampling 0.1 ohm resistance test, test input power close to the circuit board, reduce the length of the connection will be tested for efficiency Impact, it is recommended to increase the capacitance test at the input. Voltage and current test recommendations string accuracy of the ammeter is not recommended direct read power digital display. Current test can be directly connected in series with the battery, only need to ensure that the battery is less than 3.9V using a large range of ammeter test can be. colour:White/Red Material:pp/Metal Package Contents: 1 x DC5-24V Sensor Switch 2 x Charging Board Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

Brand letter dejia electronic; model tp5000 charging board Product parameters: Tp5000 lithium ion battery iron phosphate lithium battery 1a current 4.2/3.6v Function: charging lithium battery and iron phosphate lithium battery.Full of stop.Red and green double light indicator. Size: 21.5x14.5x4.2 mm Usage: tp 4056 4057 charging board is the same. - lithium batteries need only 5v power supply, output b+b - battery.Charging red light, full stop, charging the green light. - for lithium battery 3.6v phosphate iron, only soldering iron is required to open tin points between two solder plates.The power battery connection method is the same as mentioned above.If you need to recharge 4.2 v lithium battery, use the solder solder solder to connect back. Product description: Advantages: switch-pressure-relief mode, higher efficiency than linear charging circuit, and much less heat.Charge current 1a, in the constant current charge to maintain 1a.No extra heat dissipation is required to reduce the effect of heat on charging current.Reduce charging time.Optional ordinary lithium ion lithium polymer battery or lithium phosphate iron lithium battery, just one jump line can change the setting. Parameters: Input: 4.5-9v Output voltage: 4.2v/3.6v positive and negative 1% (circuit board default lithium ion battery 4.2v) Output current: default 1a After the efficiency test, it will be described in detail that if the buyer tests the efficiency and does not recommend testing the battery terminal voltage, please note skipping the rs sample 0.1 ohm resistance test. the input of power into the test is close to the circuit board and reducing the length of the connection will have an impact on the efficiency test.Voltage current test recommends that a series of ammeters with precision should not be read directly.The current test can be directly connected to the battery's positive pole, only to ensure that the battery is less than 3.9v using a large number of ammeter tests. Characteristics: The whole edition uses precious metal ceramic capacitor, x 7r temperature characteristic, performance+safety+stability far more than tantalum capacitance! Copper belt 5a large current small volume inductance, full closed magnetic low loss low interference! Single-sided machine paste, whole 4 mm ultra thin, small area heat dissipation, back copper easy installlation and paste heat dissipation film Based on dc-dc pressure relief, the efficiency is much higher than linear charging circuit, and the heating is much smaller.Charging current 1a, but the input current is only about 0.7a Optional iron phosphate lithium battery or ordinary lithium ion/lithium polymer battery, can be set in just one jump line Small size, 1 hair coin size, 1a charging without extra heat dissipation With overheat protection, overheat automatically reduces current to prevent burning Temperature characteristics of high precision resistance, full volume 1210 pr

Features: 1. Excellent quality: This Charger Module is made with advanced technology and concept. 2. High-quality battery: TP5000 lithium ion battery, 2A current 4 2/3, high quality. 6V can be switched. 3. The charging is fast: 2A version is the ultimate performance version of TP5000, due to the larger current, the heat will- be relatively large, but the fastestcharging speed 4. LED light prompt: lithium battery or lithium iron phosphate battery charging, full charged, the charging will stop, green LED light up, safe and secure. Descriptions: 1. This Charger Module is made with advanced concepts and has a fast charging speed. 2. Excellent quality and durability. Specifications: Input: 4. 5-9V (can not over 9v, suggest 5v~6v) Size: 26*19*6mm Deadline: 4.2V/3 6Ѵ; error t 1% (circuit board default 3.6V) Current: 2A Package Included: 1 x Charger Module Notes: Please allow 0-2mm error due to manual measurement, thanks for understanding. Due to the difference between different monitors, the picture may not reflect the actual color of the item. Please understand, thank you

#TP5000 #3.6v/4.2v #2A #Charger #Board #3.7v #Lithium #3.2v #LiFePO4 #Battery #Charging TP5000 3.6v/4.2v 2A Charger Board 3.7v Lithium 3.2v LiFePO4 Battery Charging Features: TP5000 lithium ion battery lithium iron phosphate battery 2A current 4.2/3.6V can be switched 2A version is the ultimate performance version of TP5000,due to the larger current, the heat will be relatively large, but the fastest charging speed Parameter Input: 4.5-9V (can not over 9v, suggest 5v~6v) Voltage:4.2V/3.6V;error ±1% (circuit board default 3.6V) Current:2A(change the sampling resistance can be adjusted, the formula is: 0.1 v/current = resistance) Function:lithium battery or lithium iron phosphate battery charging, full charged, the charging will stop, green LED light up The status indicator light is not welded and the user is required to be welded on their own Size:2.6x1.8cm/1.02x0.71inch Note: Please allow 1-3mm error due to manual measurement. pls make sure you do not mind before you bid Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you! Package Includes: 1 x TP5000 Charger

Thời gian giao hàng dự kiến cho sản phẩm này là từ 7-9 ngày Đặc trưng: Pin lithium sắt phốt phát TP5000 dòng điện 4.2/3.6V có thể được chuyển đổi Phiên bản 2A là phiên bản hiệu năng cao nhất của TP5000, do dòng điện lớn hơn nên nhiệt lượng sẽ tương đối lớn nhưng tốc độ sạc nhanh nhất Thông tin sản phẩm: Đầu vào: 4.5-9V (không thể quá 9v, phù hợp 5v ~ 6v) Điện áp: 4.2V / 3.6V; dung sai ± 1% (bảng mạch mặc định 3.6V) Dòng điện: 2A (thay đổi điện trở lấy mẫu có thể được điều chỉnh, công thức là: 0.1 v / dòng điện = điện trở) Công dụng: Sạc pin lithium hoặc pin lithium sắt phốt phát, sạc đầy, quá trình sạc sẽ dừng lại, đèn LED màu xanh lá cây sáng lên Đèn báo trạng thái chưa hàn và người dùng bắt buộc phải tự hàn Kích thước: 2.6x1.8cm / 1.02x0.71 inch Lưu ý: Xin vui lòng cho phép sai số 1-3mm do đo lường thủ công. Hãy đảm bảo rằng bạn không phiền lòng về điều này trước khi đặt hàng. Do sự khác biệt giữa các màn hình khác nhau, hình ảnh có thể không phản ánh màu sắc thực tế của sản phẩm. Xin cảm ơn! Gói hàng bao gồm: 1 x Bảng mạch sạc pin T

#DEY TP5000 Charging Board Module 3.6/4.2V Lithium Battery B151 Small Size Features: 1. Material: this charging board module is made of good material, which is durable and has long service life. 2. With overheat protection: with overheat protection, overheat will automatically reduce the current to prevent burning. 3. Full stop: full stop, two color charging status indicator. 4. Small size: dime size, 1A charging without additional cooling. 5. Easy to carry: with light weight and portable size, it is easy and convenient to carry and use. Description: This charging board module is made of good material, which is durable and has long service life, and with overheat protection, overheat will automatically reduce the current to prevent burning. Specifications: Size: 21.5*14.5*4.2mm Power: 3.6/4.2V Application area: 3C digital Current: 1A Package Included: 1* Charging board module Notes: 1. Please allow 0-1 inch error due to manual measurement. Thanks for your understanding. 2. Monitors are not calibrated same, item color displayed in photos may be showing slightly different from real ob

set2: 1 x DC5-24V Sensor Switch + 2 x Charging Board Lithium battery only need to connect a 5V power supply, output B + B-connected battery can be. Charging red light, full of self-stop, charging green light finished. For lithium iron phosphate battery 3.6V, just soldering iron solder between the two solder pad can be. Power supply battery connection method as described above. If you want to change back to charge 4.2V lithium battery, solder pad can be used to solder back. Switch buck e, the efficiency is higher than the linear charging circuit, heat is also much smaller. Charging current 1A, in the constant current full charge to maintain 1A. With overheating protection, overheating will automatically reduce the current to prevent burnout No additional heat dissipation, reducing the impact of heat on the charging current. Reduce the charging time. Optional lithium-ion lithium polymer battery or lithium iron phosphate battery, just a jumper can change the settings. Full version of the use of precious metal ceramic s, X7R temperature characteristics, performance + safety + stability far more than tantalum s! Sensitivity to light : Dark and Light environment. Sensing e: PIR sensing + light control Timer. Sensing Distance: 0.5 Meter to 5 Meter (high temperature will influence switch sensibility). Sensing e: PIR sensing + light control Timer. Charging Board Size: 21.5 x 14.5 x 4.2mm Input: 4.5-9V Output voltage: 4.2V / 3.6V plus or minus 1% (circuit board default lithium-ion battery 4.2V) Output current: default 1A After the efficiency test will be described in detail, if the buyer's own test efficiency, do not recommend testing the battery side voltage, please note that skip the Rs sampling 0.1 ohm resistance test, test input power close to the circuit board, reduce the length of the connection will be tested for efficiency Impact, it is recommended to increase the capacitance test at the input. Voltage and current test recommendations string accuracy of the ammeter is not recommended direct read power digital display. Current test can be directly connected in series with the battery, only need to ensure that the battery is less than 3.9V using a large range of ammeter test can be. colour:White/Red Material:pp/Metal Package Contents: 1 x DC5-24V Sensor Switch 2 x Charging Board Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

TP5100 Description: TP5100 is a double switch buck 8.4V, single cell 4. 2V lithium battery charge management chip. Its ultra-compact QFN16 package and simple external circuit, making TP5100 ideal for portable equipment so large current charging management applications.Meanwhile, TP5100 built-in input overcurrent, undervoltage protection, over temperature protection, short circuit protection, battery temperature monitoring, reverse battery protection. TP5100 have 5V-18V wide input voltage, dual battery trickle charge into pre-charge, constant current, constant voltage three phase, pre-charge current trickle charge current through an external resistor adjustment, the maximum charge current up to 2A. TP5100 with a frequency of 400kHz switching mode makes it possible to use a smaller outer Suo device and the large current charging still maintain a smaller amount of heat. TP51OO built-in power PMOSFET, anti-intrusion circuit, so no anti-intrusion protection and other external Schottky diode. Features: - Double 8.4v / 4.2v lithium rechargeable single - Programmable charge current. 0. 1A-2A - Programmable steady precharge current 10% -100%. - Wide operating voltage, maximum reach I8V - Red and green LED charge status indicator - Chip temperature protection, overcurrent protection, undervoltage protection - Battery temperature protection, reverse battery shutdown, short circuit protection - Switching frequency 400Khz, usable inductance 20uH and more - PWR_ON Power battery for switching control Maximum Ratings: - Static input supply voltage (VlN): 20V - BAI: -8.4V-20V - BAT Short-Circuit Duration: Continuous - Operating environment Temperature range: -40 ° -85 ° - Storage temperature range: -65 ° - 125 ° Application: - Portable equipment, various chargers - Smartphone, PDA, mobile cellular telephone - MP4, MP5 players, tablets - HM - Power Tools - Walkie-talkie Default shipping settings: 4.2V 2A. The board has with LED, and LED's external reserve position. Size: 25 * 17 * 5mm ultra-small size Input voltage: 5-18V DC power supply Charge status: full and unloaded blue lights, charging red. TP5000 Product parameters: TP5000 lithium ion battery lithium iron phosphate battery 1A current 4.2/3.6V Function: Charge lithium battery and lithium iron phosphate battery. Full of self-stop. Red and green double lights indicate. Usage: TP4056 4057 charging board usage is the same. 1. The lithium battery only needs to be connected to the 5V power supply, and the output B+B- can be connected to the battery. The red light is on during charging, and the battery is fully charged. The green light is on after charging. 2, for lithium iron phosphate battery 3.6V, just soldering iron to open the tin point between the two pads. The power battery connection method is unchanged as described above. If you need to change the charge to a 4.2V lithium battery, use the pad to solder it

We have many products in our warehouse, our warehouse is in Shenzhen . Genaral it need 1-2weeks arrive your hand. if you subimit order , we will handle in 1-3days.if you chat with us , we donot reply you, donot worry , we try to handle your order.so pls donot cancel o

We have many products in our warehouse, our warehouse is in Shenzhen . Genaral it need 1-2weeks arrive your hand. if you subimit order , we will handle in 1-3days.if you chat with us , we donot reply you, donot worry , we try to handle your order.so pls donot cancel o

Welcome to store. Wish you a happy shopping！ Features: Switch buck mode has higher efficiency and fever than linear charging circuit. Charging current 1A, in constant current charge to maintain 1A. No additional heat dissipation is needed, which reduces the influence of heating on charging current. Reduce charging time. Ordinary lithium-ion lithium polymer batteries or lithium iron phosphate batteries can be selected. Only one jumper is needed to change the settings. Specifications: Material: ABS Size: 21.5*14.5*4.2mm/0.85*0.57*0.17" Input: 4.5-9V Output voltage: 4.2V/3.6V±1% (PCB default lithium-ion battery 4.2V) Output current: default 1A Usage: 1. Lithium batteries only need to be connected with 5V power supply and output B+B-to be connected with batteries. In charging, the red light is on, the charge is full and the green light is on after charging. 2. For lithium iron phosphate batteries of 3.6V, only soldering iron is needed to open the tin spot between the two soldering pads. The connection method of the power battery is unchanged as described above. If it is necessary to recharge 4.2V lithium batteries, the solder pad can be dipped and soldered to connect the batteries. Notes: 1. Due to the different monitor and light effect, the actual color of the item might be slightly different from the color showed on the pictures. Thank you! 2. Please allow 1-3mm measuring deviation due to manual measurement. Included: 1 XBattery Charging

Hello everyone, our company is in Shenzhen。we specialize in selling electronic components. When we receive your order, we will process your order within 24 hours. If you order many items, we may need more time to process, it will not be more than 5 days, please be patient. Genaral it need 1-2weeks arrive your hand.if you chat with us , we donot reply you, donot worry , we are try to handle your order.so pls donot cancel o

We have many products in our warehouse, our warehouse is in Shenzhen . Genaral it need 1-2weeks arrive your hand. if you subimit order , we will handle in 1-3days.if you chat with us , we donot reply you, donot worry , we try to handle your order.so pls donot cancel o

Hello everyone, our company is in Shenzhen。we specialize in selling electronic components. When we receive your order, we will process your order within 24 hours. If you order many items, we may need more time to process, it will not be more than 5 days, please be patient. Genaral it need 1-2weeks arrive your hand.if you chat with us , we donot reply you, donot worry , we are try to handle your order.so pls donot cancel o

1. PCB size:21.5*14.5*4.2mm 2. Input voltage: DC 4.5-9V(Recommended not to exceed 7V) 3. Output voltage: DC 4.2V/3.6V(default 4.2V) 4. Output current: 1A(Default max) 5. LED Indicator: Charging-Red/Green Flashing,Charged-Green 6. Features:Charging for Lithium battery(4.2V) and Lithium iron phosphate battery(3.6V) 7. Switch mode: 1>. F Welding point ON for Lithium battery and output 4.2V 2>. F Welding point OFF for Lithium iron phosphate battery and output 3.6V 8. Adjust output current(need to modify two resistance value on mark "SANYA"): 1>. Default weld 1pcs R100(0.1ohm) resistor and output 1A(max) 2>. Welding 1pcs 0.2ohm resistor next to R100 and output 1.5A(max) 3>. Welding 1pcs 0.1ohm resistor next to R100 and output 2A(max) 4>. Removed R100 and welding 1pcs 0.2ohm resistor on its place and output 0.5A 5>. It requires additional heat sink if output current more tha

[Vật Tư & Linh Kiện] Kích thước PCB: 21,5 * 14,5 * 4,2mm Điện áp đầu vào: DC 4,5-9V (Khuyến nghị không vượt quá 7V) Điện áp đầu ra: DC 4.2V / 3.6V (mặc định 4.2V) Dòng điện đầu ra: 1A (Tối đa mặc định) Chỉ báo LED: Đang sạc-Đỏ / Nhấp nháy Xanh lục, Đã sạc-Xanh lục Các tính năng: Sạc cho pin Lithium (4.2V) và pin Lithium iron phosphate (3.6V) Chế độ chuyển đổi: 1. F Điểm hàn BẬT cho pin Lithium và đầu ra 4.2V 2. F Điểm hàn TẮT đối với pin Lithium iron phosphate và đầu ra 3.6V Điều chỉnh dòng điện đầu ra (cần sửa đổi hai giá trị điện trở trên nhãn "" SANYA ""): 1. Mối hàn mặc định 1 chiếc điện trở R100 (0,1ohm) và đầu ra 1A (tối đa) 2. Hàn điện trở 1 cái 0,2ohm bên cạnh R100 và đầu ra 1,5A (tối đa) 3. Hàn điện trở 1pcs 0,1ohm bên cạnh R100 và đầu ra 2A (tối đa) 4. Loại bỏ R100 và hàn điện trở 1pcs 0,2ohm vào vị trí của nó và đầu ra 0,5A 5. Nó yêu cầu tản nhiệt bổ sung nếu dòng điện đầu ra lớn hơn 1A. Liên hệ Zalo Mạnh Cường : 0356565178 để giải đáp mọi thắc mắc liên quan tới sản phẩm, dịch vụ của cửa hàng [Vật Tư & Linh Kiện] Sếp

Dear, welcome to the store. All new products, carefully selected by the store owner, which can well decorate your home, and are very ornamental products, not to be missed~ Features: Switch buck mode has higher efficiency and fever than linear charging circuit. Charging current 1A, in constant current charge to maintain 1A. No additional heat dissipation is needed, which reduces the influence of heating on charging current. Reduce charging time. Ordinary lithium-ion lithium polymer batteries or lithium iron phosphate batteries can be selected. Only one jumper is needed to change the settings. Specifications: Material: ABS Size: 21.5*14.5*4.2mm/0.85*0.57*0.17" Input: 4.5-9V Output voltage: 4.2V/3.6V±1% (PCB default lithium-ion battery 4.2V) Output current: default 1A Usage: 1. Lithium batteries only need to be connected with 5V power supply and output B+B-to be connected with batteries. In charging, the red light is on, the charge is full and the green light is on after charging. 2. For lithium iron phosphate batteries of 3.6V, only soldering iron is needed to open the tin spot between the two soldering pads. The connection method of the power battery is unchanged as described above. If it is necessary to recharge 4.2V lithium batteries, the solder pad can be dipped and soldered to connect the batteries. Notes: 1. Due to the different monitor and light effect, the actual color of the item might be slightly different from the color showed on the pictures. Thank you! 2. Please allow 1-3mm measuring deviation due to manual measurement. Included: 1 XBattery Charging

Description: 1. PCB size:21.5*14.5*4.2mm 2. Input voltage: DC 4.5-9V(Recommended not to exceed 7V) 3. Output voltage: DC 4.2V/3.6V(default 4.2V) 4. Output current: 1A(Default max) 5. LED Indicator: Charging-Red/Green Flashing,Charged-Green 6. Features:Charging for Lithium battery(4.2V) and Lithium iron phosphate battery(3.6V) 7. Switch mode: 1>. F Welding point ON for Lithium battery and output 4.2V 2>. F Welding point OFF for Lithium iron phosphate battery and output 3.6V 8. Adjust output current(need to modify two resistance value on mark "SANYA"): 1>. Default weld 1pcs R100(0.1ohm) resistor and output 1A(max) 2>. Welding 1pcs 0.2ohm resistor next to R100 and output 1.5A(max) 3>. Welding 1pcs 0.1ohm resistor next to R100 and output 2A(max) 4>. Removed R100 and welding 1pcs 0.2ohm resistor on its place and output 0.5A 5>. It requires additional heat sink if output current more tha

TP5000 DC 4.5v-9v 4.2V/3.6V 1A Lithium Battery Charging Board Lithium Iron Phosphate Charger Power Supply Module Description: 1. PCB size:21.5*14.5*4.2mm 2. Input voltage: DC 4.5-9V(Recommended not to exceed 7V) 3. Output voltage: DC 4.2V/3.6V(default 4.2V) 4. Output current: 1A(Default max) 5. LED Indicator: Charging-Red/Green Flashing,Charged-Green 6. Features:Charging for Lithium battery(4.2V) and Lithium iron phosphate battery(3.6V) 7. Switch mode: 1>. F Welding point ON for Lithium battery and output 4.2V 2>. F Welding point OFF for Lithium iron phosphate battery and output 3.6V 8. Adjust output current(need to modify two resistance value on mark "SANYA"): 1>. Default weld 1pcs R100(0.1ohm) resistor and output 1A(max) 2>. Welding 1pcs 0.2ohm resistor next to R100 and output 1.5A(max) 3>. Welding 1pcs 0.1ohm resistor next to R100 and output 2A(max) 4>. Removed R100 and welding 1pcs 0.2ohm resistor on its place and output 0.5A 5>. It requires additional heat sink if output current more than 1A. Full charged :red light light for a long time. Package includes: 1pcs * TP5000 DC 4.5v-9v 4.2V/3.6V 1A Lithium Battery Charging Board Before purchase: 1. All the goods are in stock and we will dispatch immediately if we receive the order. 2.Please read the item description, if you have any question, do not hesitate to contact us. Shipment： 1.1-2 days to ship(except for the pro-order item) After purchase: 1.If you are satisfied，please give us 5 stars praise. 2.Please contact us before you are going to give us bad review. We are helpful and will solve the problems. if you receive a defect item,please contact us at once with item picture or video #TP5000 #DC #4.5v-9v #4.2V #3.6V #1A #Lithium #Battery #Charging #Board #Lithium #Iron #Phosphate #Charger #Power #Supply #M

1. PCB size:21.5*14.5*4.2mm 2. Input voltage: DC 4.5-9V(Recommended not to exceed 7V) 3. Output voltage: DC 4.2V/3.6V(default 4.2V) 4. Output current: 1A(Default max) 5. LED Indicator: Charging-Red/Green Flashing,Charged-Green 6. Features:Charging for Lithium battery(4.2V) and Lithium iron phosphate battery(3.6V) 7. Switch mode: 1>. F Welding point ON for Lithium battery and output 4.2V 2>. F Welding point OFF for Lithium iron phosphate battery and output 3.6V 8. Adjust output current(need to modify two resistance value on mark "SANYA"): 1>. Default weld 1pcs R100(0.1ohm) resistor and output 1A(max) 2>. Welding 1pcs 0.2ohm resistor next to R100 and output 1.5A(max) 3>. Welding 1pcs 0.1ohm resistor next to R100 and output 2A(max) 4>. Removed R100 and welding 1pcs 0.2ohm resistor on its place and output 0.5A 5>. It requires additional heat sink if output current more than

Welcome to the shop, the quality is excellent and the price is affordable!✨ #ifaylky.vn Features: 1. Excellent quality: This Module is made with advanced technology and concept. 2. High-quality : TP5000 lithium ion , 2A current 4 2/3, high quality. 6V can be switched. 3. The charging is fast: 2A version is the ultimate performance version of TP5000, due to the larger current, the heat will- be relatively large, but the fastestcharging speed 4. LED light prompt: lithium or lithium iron phosphate charging, full charged, the charging will stop, green LED light up, safe and secure. Descriptions: 1. This Module is made with advanced concepts and has a fast charging speed. 2. Excellent quality and durability. Specifications: Input: 4. 5-9V (can not over 9v, suggest 5v~6v) Size: 26*19*6mm Deadline: 4.2V/3 6Ѵ; error t 1% (circuit board default 3.6V) Current: 2A Package Included: 1 x Module Notes: Please allow 0-2mm error due to manual measurement, thanks for understanding. Due to the difference between different monitors, the picture may not reflect the actual color of the item. Please understand, thank