Mach dieu khien dong co bldc

"Mini three-phase sensorless brushless (BLDC) DC motor speed controller adopts imported chips for wide voltage, and at the same time, it has power input reverse connection protection and does not burn if it is connected reversely. It has output phase loss and stall fault indication, which can drive three-phase three-wire, three Phase four-wire small brushless motor, low sine wave and small volume Model: ZS-X9 Name: 15W three-phase sensorless brushless motor driver Working voltage: DC5V-15V Working current: 1.5A continuous (peak 2A) Control power: 15W (Z large) Quiescent current: 0.005A (standby state) PWM duty cycle: 1%-100% Size: 38MMx width 26.5MM (without handle) total height 15MM Tips: Buyers do not have to read the following precautions: 1. This mini brushless DC motor controller is highly integrated. The power supply is DC and cannot be connected to AC. Please use it within the voltage and current range of the parameters indicated on the webpage. There are many types of brushless motors, which are also matched with the speed controller. Pay attention to, we do not guarantee that it can be applied to all brushless motors, please make sure that the wiring is correct and firm before powering on and testing the machine. 2. The protection circuit of this speed governor is relatively complete. The input power supply has reverse connection protection, and it will not burn when connected reversely. There is a set of current limiting detection circuit inside the chip when it is working. The normal working continuous current is within 1.5A and the peak value is 2A. , Current and power motors are suitable for use. If the parameters are too far apart, they are not suitable for use. If they are used forcibly, there will be some undesirable phenomena that will burn the main chip, the motor line is lacking phase, and the locked rotor is protected and there is an instruction to not burn This drive is not suitable for a long time, and it is strictly prohibited to have poor contact (the brushless motor can start and run normally, and the internal current of the chip will increase the current when it is started. If the motor wire is poorly connected, it will send out a false start signal, especially Z is easy to burn out the driver chip at high voltage, so YUAN will not be covered by the warranty due to the burned chip) 3. This driver is mainly used for three-phase brushless motors with a power of no more than 15W. It cannot be used to drive brushed motors. Each product is tested on load when it is packaged at the factory, and it is guaranteed to be 100% OK before shipment. Deliberately find faults due to improper use. Please detour, in order to protect the rights and interests of the company’s products, prevent thinking people from copying the board exactly, the main chip on this driver is temporarily polished, if you mind, don’t shoot, we provide technical support for the use of the product, and small problems can be communicated sol

Description: 100% brand new and high quality! MA MB MC phase line output connection motor. VCC GND external DC power supply line. Full patch process, stable performance, with positive and negative reversal function. Wide voltage and high power motors for general use. Standard heat sink, easy to use. Specification: Material: Electronic component Color: As shown Size: About 63 x 45 x 27 mm Working voltage: 5-36V Maximum current: 16A Maximum power: 350W Overcurrent protection: Yes Package includes:     1pc x Motor Controller Note: 1. Due to the light and screen difference, the item's color may be slightly different from the pictures. 2. Please allow 1-2 cm differences due to manual measurement. #Motor #Controller #For #BLDC #Bicycle #Speed #Driver #Board #Easy #Apply #Mini #Professional #Stable #Brushless #E

YT♫DC 5v-12v 2a 15w brushless motor speed controller no hall bldc board Specifications: Working Voltage: DC 5V-12V (MAX. 15V) Working Current: 1.5A (MAX. 2A) Maximum Rated Power: 15W Static Current: 0.005A (Stand by) PWM Duty Cycle: 10000 RPM Board Size: 30x25mm/1.18x0.98" Quantity: 1 Pc Package Includes: 1 x DC Motor Drive

Tính năng sản phẩm:   - Mạch điều khiển BLDC 3 pha 6V – 50V 380W dùng cho các loại đông cơ không chổi than 3 pha có điện áp từ 6V đến 50V với mức công suất 380W. - Mạch vàng có tản nhiệt này có thể hoạt động bình thường mà không cần sensor hall. - Bo mạch có thể sử dụng để điều khiển cho các loại động cơ 3 pha không chổi than, motor brushless 3 pha, động cơ phát điện, chế quạt, chế cho các BLDC 3 pha chế tàu thuyền,… - Các chân kết nối: + Cấp nguồn VCC GND + 3 dây pha ra motor U V W + Nguồn điện ra 5V GND (dòng dưới 30 mA) + Tín hiệu điều khiển tốc độ (speed controller) qua biến trở hoặc PWM 0V-5VDC. + Tín hiệu điều khiển chiều quay thuận/nghịch (chân DIR). + Tín hiệu phanh hãm motor (BRAKE).   - Lưu ý: + Mạch nguồn của main board không có cầu chì, việc tự bổ sung có sẵn sẽ khiến chip board bị hỏng vĩnh viễn (dù là 2 giây). + Trong quá trình hoạt động bình thường, có bảo vệ quá dòng lấy mẫu ở đầu ra động cơ. Vì công suất và dòng điện của module rất lớn nên không được đoản mạch khi module không hoạt động bình thường. Khi đoản mạch có khả năng cháy đường dây, máy kiểm tra dây đầu tiên sử dụng dòng điện thấp và điện áp thấp, sau khi ok, dòng điện cao và điện áp cao đi qua, vì là module bo mạch trần, chú ý đến đường dây cách điện, điện áp mạnh không được phép chạm vào các bộ phận của bo mạch. + Không kết nối động cơ rõ ràng không phù hợp với điện áp và dòng điện của mô-đun truyền động hoặc ở xa nhau.   Thông số kĩ thuật:   - Điện áp hoạt động: 6.5-50V - Dòng tối đa: 16 đến 20A - Công suất tối đa: 380 W - Tốc độ tối đa: + 224000 RPM (động cơ 2 cực) + 74000 RPM (động cơ 6 cực) + 40000 RPM (động cơ 12 cực) + 35000 RPM (động cơ 14 cực) - Bảo vệ quá nhiệt: Có (nóng hơn 100 độ C, công suất sẽ giảm một nửa) - Bảo vệ quá dòng: Có (dòng điện sẽ tự động giảm sau khi quá tải) - Bảo vệ chạm chập: không (cần thêm cầu chì bên ngoài) - Kích thước: dài 63x45x30mm. #dieutoc #dieukhientocdo #dieukhiendienap #dieutocdc #dieutocdongco #dieutocdon

Interface Description:MA MB MC phase line output motor;5V GND motherboard with its own power supply (current does not exceed 30 mA);VDC GND main motor power supply (external DC power supply);SC speed pulse signal output;Control interface forward and backward (can also drive external switch);VR speed signal input (the integrated potentiometer speed control can also be connected to the external 0-5V speed control;brake Overheat protection: Yes (more than 100, half the power is reduced) Maximum speed: 224000 RPM (2-pole motor), 74000 RPM (6-pole motor), 40000 RPM (12-pole motor), 35000 RPM (14-pole motor) Motherboard specifications: Product Name: 380W Brushless DC Motor Driver Operating voltage: 6.5-50V Maximum current: Nominal peak from 16 to 20A Maximum power: 380 W Overcurrent protection: no (external fuse required) Blocking protection: Yes (the current will be lowered automatically after blocking) Colour:yellow Material:plastic Size:length 63 MM * width 45 MM * height 30 MM Package Contents: 1*Motor controller board Precautions: 1. The power circuit of the main board has no fuse, and the built-in self-addition will cause the board chip to be permanently damaged (even if it is 2 seconds). 2. During normal operation, there is a sampling overcurrent protection at the motor output. Since the power and current of the ule are very large, do not short circuit when the ule does not work normally. Once the short circuit has the possibility of burning the line, the first wiring test machine uses low current and low voltage, after ok, high current and high voltage passes, because it is a bare board ule for sale , pay attention to the wiring line insulation, strong voltage is not allowed to touch the board parts. 3. Do not connect the motor that is clearly inconsistent with the voltage and current of the drive ule or that is far from each other. Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

【OMO】DC 5V-12V 2A 15W brushless motor speed controller no hall bldc driver boardSpecifications: Working Voltage: DC 5V-12V (MAX. 15V) Working Current: 1.5A (MAX. 2A) Maximum Rated Power: 15W Static Current: 0.005A (Stand by) PWM Duty Cycle: 10000 RPM Board Size: 30x25mm/1.18x0.98" Note: Please allow 1-3mm error due to manual measurement. pls make sure you do not mind before you bid Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you! No Retail Package Package Includes: 1 x DC Motor Drive

Description: 100% brand new and high quality! MA MB MC phase line output connection motor. VCC GND external DC power supply line. Full patch process, stable performance, with positive and negative reversal function. Wide voltage and high power motors for general use. Standard heat sink, easy to use. Specification: Material: Electronic component Color: As shown Size: About 63 x 45 x 27 mm Working voltage: 5-36V Maximum current: 16A Maximum power: 350W Overcurrent protection: Yes Package includes:     1pc x Motor Controller Note: 1. Due to the light and screen difference, the item's color may be slightly different from the pictures. 2. Please allow 1-2 cm differences due to manual measurement. #Motor #Controller #For #BLDC #Bicycle #Speed #Driver #Board #Easy #Apply #Mini #Professional #Stable #Brushless #E

Tính năng sản phẩm:   - Bộ điều tốc động cơ Brushless không chổi than 5V – 36V 15A là bộ điều tốc dùng cho các động cơ 3 pha, động cơ không chổi than, động cơ BLDC, brushless với công suất tối đa 15A. - Bộ điều khiển tốc độ động cơ không chổi than PWM, WUV, Clock, ESC có đảo chiều DC 5V-36V được thiết kế nhỏ gọn, tích hợp công tắc đảo chiều. - Bộ điều tốc có nắp hộp bảo vệ vừa tạo thẩm mĩ, vừa bảo vệ mạch bên trong khỏi va đập. - Bộ điều tốc này dùng cho động cơ brushless không cần cảm biến từ trường (hall sensor) - Bộ điều khiển tốc độ động cơ này có núm xoay điều chỉnh tốc độ giúp người dùng dễ dàng sử dụng và tiện ích. - Bộ điều tốc dùng chiết áp có công tắc bật tắc 100k và công tắt đảo chiều động cơ nhằm điều khiển tốc độ và thay đổi hướng quay động cơ cw, ccw. - Bộ điều tốc điều chỉnh phạm vi tốc độ từ 0 đến 100% - Bộ điều tốc thích hợp để điều tốc động cơ không chổi than, brushless chế quạt, động cơ 3 pha, động cơ không chổi than 5V, 12V, 24V, 36V…   Bộ điều tốc có thể đấu theo sơ đồ đấu:   - Sơ đồ đấu hình sao - Sơ đồ đấu tam giác   Lưu ý: Nếu muốn mở nắp hộp sản phẩm, vui lòng rút hết đầu jack dây để tránh đứt chân cáp Thông số kỹ thuật:   -  Điện áp: 5V – 36VDC (tùy thuộc vào điện áp của motor, cấp nguồn vào cho phù hợp) -  Dòng tải định mức: 15A -  Phạm vi điều chỉnh tốc độ: 0 – 100% -  Chế độ điều khiển tốc độ: Chiết áp (tuyến tính 270 độ) -  Hỗ trợ các động cơ brushless 3 pha -  Có công tắc đảo chiều -  Kích thước: 100 x 68 x 40mm -  Trọng lượng: 98g #dieutoc #dieukhientocdo #dieukhiendienap #dieutocdc #dieutocdongco #dieutocdon

Interface Description:MA MB MC phase line output motor;5V GND motherboard with its own power supply (current does not exceed 30 mA);VDC GND main motor power supply (external DC power supply);SC speed pulse signal output;Control interface forward and backward (can also drive external switch);VR speed signal input (the integrated potentiometer speed control can also be connected to the external 0-5V speed control;brake Overheat protection: Yes (more than 100, half the power is reduced) Maximum speed: 224000 RPM (2-pole motor), 74000 RPM (6-pole motor), 40000 RPM (12-pole motor), 35000 RPM (14-pole motor) Motherboard specifications: Product Name: 380W Brushless DC Motor Driver Operating voltage: 6.5-50V Maximum current: Nominal peak from 16 to 20A Maximum power: 380 W Overcurrent protection: no (external fuse required) Blocking protection: Yes (the current will be lowered automatically after blocking) Colour:yellow Material:plastic Size:length 63 MM * width 45 MM * height 30 MM Package Contents: 1*Motor controller board Precautions: 1. The power circuit of the main board has no fuse, and the built-in self-addition will cause the board chip to be permanently damaged (even if it is 2 seconds). 2. During normal operation, there is a sampling overcurrent protection at the motor output. Since the power and current of the module are very large, do not short circuit when the module does not work normally. Once the short circuit has the possibility of burning the line, the first wiring test machine uses low current and low voltage, after ok, high current and high voltage passes, because it is a bare board module for sale , pay attention to the wiring line insulation, strong voltage is not allowed to touch the board parts. 3. Do not connect the motor that is clearly inconsistent with the voltage and current of the drive module or that is far from each other. Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

note: This drive is a DC three-phase brushless and Hallless control board, and the motor can work normally without Hall. BLDC wide voltage 6.5-50V, high power 380W, DC three-phase high speed brushless sensorless controller, new PWM signal input, support 3.3V, PLC 0-5V analog quantity, signal control Interface Description: 1. U V W phase line output is connected to the motor 2.5V GND motherboard comes with power supply (current does not exceed 300MA) 3. VCC GND motor main power supply (external DC power supply) 4. SC speed pulse signal output 5. DIR forward and reverse control (can be connected to the switch) 6. BRAKE brake control (the lead wire can be connected with an external switch) 7.0-5V PWM speed control signal input (on-board potentiometer speed control can also be switched by jumper to connect an external 0-5V analog quantity PWM duty cycle signal input speed control) parameter: Name: 380W brushless DC motor controller without Hall Model: ZS-X11F Working voltage: 6.5-50V Drive current: rated 16A, plus air cooling 30A Maximum power: 380W Overcurrent protection: no (need to connect an external fuse) Locked rotor protection: Yes (the current will automatically drop after locked rotor) Over-temperature protection: Yes (over 100 degrees, the power is reduced by half) Maximum speed: 224000 RPM (2 pole motor), 74000 RPM (6 pole motor), 40000 RPM (12 pole motor), 35000 RPM (14 pole motor). Size: length 63MM*width 45MM*height 31MM Precautions: 1. There is no fuse in the power supply circuit on the main board. Jianyi has added it himself. Reversed connection of the positive and negative poles of the power supply will cause permanent damage to some of the chips on the board (even for 1 second) 2. There is sampling over-current protection at the output of the motor during normal operation. Because the power and current of the module are very large, please do not artificially short-circuit when the module is not working normally. Once the short-circuit, the circuit may be burnt and the tube may burst. Please use small current and low voltage test, after ok, then apply high current and high voltage. Because it is a bare board module, please pay attention to the insulation of the wiring head. It is forbidden for strong voltage to touch the board parts 3. Do not connect to the motor that is obviously inconsistent with the drive module voltage, current, or power, to avoid inexplicable "nonsensical" d

Interface Description:MA MB MC phase line output motor;5V GND motherboard with its own power supply (current does not exceed 30 mA);VDC GND main motor power supply (external DC power supply);SC speed pulse signal output;Control interface forward and backward (can also drive external switch);VR speed signal input (the integrated potentiometer speed control can also be connected to the external 0-5V speed control;brake Overheat protection: Yes (more than 100, half the power is reduced) Maximum speed: 224000 RPM (2-pole motor), 74000 RPM (6-pole motor), 40000 RPM (12-pole motor), 35000 RPM (14-pole motor) Motherboard specifications: Product Name: 380W Brushless DC Motor Driver Operating voltage: 6.5-50V Maximum current: Nominal peak from 16 to 20A Maximum power: 380 W Overcurrent protection: no (external fuse required) Blocking protection: Yes (the current will be lowered automatically after blocking) Colour:yellow Material:plastic Size:length 63 MM * width 45 MM * height 30 MM Package Contents: 1*Motor controller board Precautions: 1. The power circuit of the main board has no fuse, and the built-in self-addition will cause the board chip to be permanently damaged (even if it is 2 seconds). 2. During normal operation, there is a sampling overcurrent protection at the motor output. Since the power and current of the module are very large, do not short circuit when the module does not work normally. Once the short circuit has the possibility of burning the line, the first wiring test machine uses low current and low voltage, after ok, high current and high voltage passes, because it is a bare board module for sale , pay attention to the wiring line insulation, strong voltage is not allowed to touch the board parts. 3. Do not connect the motor that is clearly inconsistent with the voltage and current of the drive module or that is far from each other. Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

Specifications: Working Voltage: DC 5V-12V (MAX. 15V) Working Current: 1.5A (MAX. 2A) Maximum Rated Power: 15W Static Current: 0.005A (Stand by) PWM Duty Cycle: 10000 RPM Board Size: 30x25mm/1.18x0.98" Note: Please allow 1-3mm error due to manual measurement. pls make sure you do not mind before you bid Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you! No Retail Package Package Includes: 1 x DC Motor Drive

Interface Description:MA MB MC phase line output motor;5V GND motherboard with its own power supply (current does not exceed 30 mA);VDC GND main motor power supply (external DC power supply);SC speed pulse signal output;Control interface forward and backward (can also drive external switch);VR speed signal input (the integrated potentiometer speed control can also be connected to the external 0-5V speed control;brake Overheat protection: Yes (more than 100, half the power is reduced) Maximum speed: 224000 RPM (2-pole motor), 74000 RPM (6-pole motor), 40000 RPM (12-pole motor), 35000 RPM (14-pole motor) Motherboard specifications: Product Name: 380W Brushless DC Motor Driver Operating voltage: 6.5-50V Maximum current: Nominal peak from 16 to 20A Maximum power: 380 W Overcurrent protection: no (external fuse required) Blocking protection: Yes (the current will be lowered automatically after blocking) Colour:yellow Material:plastic Size:length 63 MM * width 45 MM * height 30 MM Package Contents: 1*Motor controller board Precautions: 1. The power circuit of the main board has no fuse, and the built-in self-addition will cause the board chip to be permanently damaged (even if it is 2 seconds). 2. During normal operation, there is a sampling overcurrent protection at the motor output. Since the power and current of the ule are very large, do not short circuit when the ule does not work normally. Once the short circuit has the possibility of burning the line, the first wiring test machine uses low current and low voltage, after ok, high current and high voltage passes, because it is a bare board ule for sale , pay attention to the wiring line insulation, strong voltage is not allowed to touch the board parts. 3. Do not connect the motor that is clearly inconsistent with the voltage and current of the drive ule or that is far from each other. Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

Specifications: Working Voltage: DC 5V-12V (MAX. 15V) Working Current: 1.5A (MAX. 2A) Maximum Rated Power: 15W Static Current: 0.005A (Stand by) PWM Duty Cycle: 10000 RPM Board Size: 30x25mm/1.18x0.98" Quantity: 1 Pc Package Includes: 1 x DC Motor Drive

Operating voltage:DC 12V-36V Operating Current:<=15A Driver Power:<=500W Speed Voltage:0.1V-5V Operating Temperature:-40-85°C Humidity:90%RH Stall protection:Yes Enable Control:Yes Over-current protection:Yes Steering control:Yes Speed control signal:Yes Size:6.3x4.2cm/2.48x1.65inch Note: Please allow 1-3mm error due to manual measurement.pls make sure you do not mind before you bid. Due to the difference between different monitors,the picture may not reflect the actual color of the item.Thank you! Package Includes: 1x Brushless Motor Speed Contr

Welcome to 【Withbetin Store】 ,We insist on the lowest price to sell the best quality items！！！Specifications: Working Voltage: DC 5V-12V (MAX. 15V) Working Current: 1.5A (MAX. 2A) Maximum Rated Power: 15W Static Current: 0.005A (Stand by) PWM Duty Cycle: 10000 RPM Board Size: 30x25mm/1.18x0.98" Note: Please allow 1-3mm error due to manual measurement. pls make sure you do not mind before you bid Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you! No Retail Package Package Includes: 1 x DC Motor Drive

Interface Description:MA MB MC phase line output motor;5V GND motherboard with its own power supply (current does not exceed 30 mA);VDC GND main motor power supply (external DC power supply);SC speed pulse signal output;Control interface forward and backward (can also drive external switch);VR speed signal input (the integrated potentiometer speed control can also be connected to the external 0-5V speed control;brake Overheat protection: Yes (more than 100, half the power is reduced) Maximum speed: 224000 RPM (2-pole motor), 74000 RPM (6-pole motor), 40000 RPM (12-pole motor), 35000 RPM (14-pole motor) Motherboard specifications: Product Name: 380W Brushless DC Motor Driver Operating voltage: 6.5-50V Maximum current: Nominal peak from 16 to 20A Maximum power: 380 W Overcurrent protection: no (external fuse required) Blocking protection: Yes (the current will be lowered automatically after blocking) Colour:yellow Material:plastic Size:length 63 MM * width 45 MM * height 30 MM Package Contents: 1*Motor controller board Precautions: 1. The power circuit of the main board has no fuse, and the built-in self-addition will cause the board chip to be permanently damaged (even if it is 2 seconds). 2. During normal operation, there is a sampling overcurrent protection at the motor output. Since the power and current of the ule are very large, do not short circuit when the ule does not work normally. Once the short circuit has the possibility of burning the line, the first wiring test machine uses low current and low voltage, after ok, high current and high voltage passes, because it is a bare board ule for sale , pay attention to the wiring line insulation, strong voltage is not allowed to touch the board parts. 3. Do not connect the motor that is clearly inconsistent with the voltage and current of the drive ule or that is far from each other. Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

mạch điều khiển BLDC 3 pha 6V – 50V 380W dùng cho các loại đông cơ không chổi than 3 pha có điện áp từ 6V đến 50V với mức công suất 380W. - Mạch vàng có tản nhiệt này có thể hoạt động bình thường mà không cần sensor hall. - Bo mạch có thể sử dụng để điều khiển cho các loại động cơ 3 pha không chổi than, motor brushless 3 pha, động cơ phát điện, chế quạt, chế cho các BLDC 3 pha chế tàu thuyền,… - Các chân kết nối: + Cấp nguồn VCC GND + 3 dây pha ra motor U V W + Nguồn điện ra 5V GND (dòng dưới 30 mA) + Tín hiệu điều khiển tốc độ (speed controller) qua biến trở hoặc PWM 0V-5VDC. + Tín hiệu điều khiển chiều quay thuận/nghịch (chân DIR). + Tín hiệu phanh hãm motor (BRAKE). - Lưu ý: + Mạch nguồn của main board không có cầu chì, việc tự bổ sung có sẵn sẽ khiến chip board bị hỏng vĩnh viễn (dù là 2 giây). + Trong quá trình hoạt động bình thường, có bảo vệ quá dòng lấy mẫu ở đầu ra động cơ. Vì công suất và dòng điện của module rất lớn nên không được đoản mạch khi module không hoạt động bình thường. Khi đoản mạch có khả năng cháy đường dây, máy kiểm tra dây đầu tiên sử dụng dòng điện thấp và điện áp thấp, sau khi ok, dòng điện cao và điện áp cao đi qua, vì là module bo mạch trần, chú ý đến đường dây cách điện, điện áp mạnh không được phép chạm vào các bộ phận của bo mạch. + Không kết nối động cơ rõ ràng không phù hợp với điện áp và dòng điện của mô-đun truyền động hoặc ở xa nhau. Thông số kĩ thuật: - Điện áp hoạt động: 6.5-50V - Dòng tối đa: 16 đến 20A - Công suất tối đa: 380 W - Tốc độ tối đa: + 224000 RPM (động cơ 2 cực) + 74000 RPM (động cơ 6 cực) + 40000 RPM (động cơ 12 cực) + 35000 RPM (động cơ 14 cực) - Bảo vệ quá nhiệt: Có (nóng hơn 100 độ C, công suất sẽ giảm một nửa) - Bảo vệ quá dòng: Có (dòng điện sẽ tự động giảm sau khi quá tải) - Bảo vệ chạm chập: không (cần thêm cầu chì bên ngoài) - Kích thước: dài 63x45x

Description: 100% brand new and high quality! MA MB MC phase line output connection motor. VCC GND external DC power supply line. Full patch process, stable performance, with positive and negative reversal function. Wide voltage and high power motors for general use. Standard heat sink, easy to use. Specification: Material: Electronic component Color: As shown Size: About 63 x 45 x 27 mm Working voltage: 5-36V Maximum current: 16A Maximum power: 350W Overcurrent protection: Yes Package includes:     1pc x Motor Controller Note: 1. Due to the light and screen difference, the item's color may be slightly different from the pictures. 2. Please allow 1-2 cm differences due to manual measurement. #Motor #Controller #For #BLDC #Bicycle #Speed #Driver #Board #Easy #Apply #Mini #Professional #Stable #Brushless #E

Interface Description:MA MB MC phase line output motor;5V GND motherboard with its own power supply (current does not exceed 30 mA);VDC GND main motor power supply (external DC power supply);SC speed pulse signal output;Control interface forward and backward (can also drive external switch);VR speed signal input (the integrated potentiometer speed control can also be connected to the external 0-5V speed control;brake Overheat protection: Yes (more than 100, half the power is reduced) Maximum speed: 224000 RPM (2-pole motor), 74000 RPM (6-pole motor), 40000 RPM (12-pole motor), 35000 RPM (14-pole motor) Motherboard specifications: Product Name: 380W Brushless DC Motor Driver Operating voltage: 6.5-50V Maximum current: Nominal peak from 16 to 20A Maximum power: 380 W Overcurrent protection: no (external fuse required) Blocking protection: Yes (the current will be lowered automatically after blocking) Colour:yellow Material:plastic Size:length 63 MM * width 45 MM * height 30 MM Package Contents: 1*Motor controller board Precautions: 1. The power circuit of the main board has no fuse, and the built-in self-addition will cause the board chip to be permanently damaged (even if it is 2 seconds). 2. During normal operation, there is a sampling overcurrent protection at the motor output. Since the power and current of the module are very large, do not short circuit when the module does not work normally. Once the short circuit has the possibility of burning the line, the first wiring test machine uses low current and low voltage, after ok, high current and high voltage passes, because it is a bare board module for sale , pay attention to the wiring line insulation, strong voltage is not allowed to touch the board parts. 3. Do not connect the motor that is clearly inconsistent with the voltage and current of the drive module or that is far from each other. Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3c

Description: 100% brand new and high quality! MA MB MC phase line output connection motor. VCC GND external DC power supply line. Full patch process, stable performance, with positive and negative reversal function. Wide voltage and high power motors for general use. Standard heat sink, easy to use. Specification: Material: Electronic component Color: As shown Size: About 63 x 45 x 27 mm Working voltage: 5-36V Maximum current: 16A Maximum power: 350W Overcurrent protection: Yes Package includes:     1pc x Motor Controller Note: 1. Due to the light and screen difference, the item's color may be slightly different from the pictures. 2. Please allow 1-2 cm differences due to manual measurement. #Motor #Controller #For #BLDC #Bicycle #Speed #Driver #Board #Easy #Apply #Mini #Professional #Stable #Brushless #E

note: This drive is a DC three-phase brushless and Hallless control board, and the motor can work normally without Hall. BLDC wide voltage 6.5-50V, high power 380W, DC three-phase high speed brushless sensorless controller, new PWM signal input, support 3.3V, PLC 0-5V analog quantity, signal control Interface Description: 1. U V W phase line output is connected to the motor 2.5V GND motherboard comes with power supply (current does not exceed 300MA) 3. VCC GND motor main power supply (external DC power supply) 4. SC speed pulse signal output 5. DIR forward and reverse control (can be connected to the switch) 6. BRAKE brake control (the lead wire can be connected with an external switch) 7.0-5V PWM speed control signal input (on-board potentiometer speed control can also be switched by jumper to connect an external 0-5V analog quantity PWM duty cycle signal input speed control) parameter: Name: 380W brushless DC motor controller without Hall Model: ZS-X11F Working voltage: 6.5-50V Drive current: rated 16A, plus air cooling 30A Maximum power: 380W Overcurrent protection: no (need to connect an external fuse) Locked rotor protection: Yes (the current will automatically drop after locked rotor) Over-temperature protection: Yes (over 100 degrees, the power is reduced by half) Maximum speed: 224000 RPM (2 pole motor), 74000 RPM (6 pole motor), 40000 RPM (12 pole motor), 35000 RPM (14 pole motor). Size: length 63MM*width 45MM*height 31MM Precautions: 1. There is no fuse in the power supply circuit on the main board. Jianyi has added it himself. Reversed connection of the positive and negative poles of the power supply will cause permanent damage to some of the chips on the board (even for 1 second) 2. There is sampling over-current protection at the output of the motor during normal operation. Because the power and current of the module are very large, please do not artificially short-circuit when the module is not working normally. Once the short-circuit, the circuit may be burnt and the tube may burst. Please use small current and low voltage test, after ok, then apply high current and high voltage. Because it is a bare board module, please pay attention to the insulation of the wiring head. It is forbidden for strong voltage to touch the board parts 3. Do not connect to the motor that is obviously inconsistent with the drive module voltage, current, or power, to avoid inexplicable "nonsensical" d

Interface Description:MA MB MC phase line output motor;5V GND motherboard with its own power supply (current does not exceed 30 mA);VDC GND main motor power supply (external DC power supply);SC speed pulse signal output;Control interface forward and backward (can also drive external switch);VR speed signal input (the integrated potentiometer speed control can also be connected to the external 0-5V speed control;brake Overheat protection: Yes (more than 100, half the power is reduced) Maximum speed: 224000 RPM (2-pole motor), 74000 RPM (6-pole motor), 40000 RPM (12-pole motor), 35000 RPM (14-pole motor) Motherboard specifications: Product Name: 380W Brushless DC Motor Driver Operating voltage: 6.5-50V Maximum current: Nominal peak from 16 to 20A Maximum power: 380 W Overcurrent protection: no (external fuse required) Blocking protection: Yes (the current will be lowered automatically after blocking) Colour:yellow Material:plastic Size:length 63 MM * width 45 MM * height 30 MM Package Contents: 1*Motor controller board Precautions: 1. The power circuit of the main board has no fuse, and the built-in self-addition will cause the board chip to be permanently damaged (even if it is 2 seconds). 2. During normal operation, there is a sampling overcurrent protection at the motor output. Since the power and current of the ule are very large, do not short circuit when the ule does not work normally. Once the short circuit has the possibility of burning the line, the first wiring test machine uses low current and low voltage, after ok, high current and high voltage passes, because it is a bare board ule for sale , pay attention to the wiring line insulation, strong voltage is not allowed to touch the board parts. 3. Do not connect the motor that is clearly inconsistent with the voltage and current of the drive ule or that is far from each other. Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

【YUL】DC 5v-12v 2a 15w brushless motor speed controller no hall bldc board moduleSpecifications: Working Voltage: DC 5V-12V (MAX. 15V) Working Current: 1.5A (MAX. 2A) Maximum Rated Power: 15W Static Current: 0.005A (Stand by) PWM Duty Cycle: 10000 RPM Board Size: 30x25mm/1.18x0.98" Quantity: 1 Pc Package Includes: 1 x DC Motor Drive

Description: 100% brand new and high quality! MA MB MC phase line output connection motor. VCC GND external DC power supply line. Full patch process, stable performance, with positive and negative reversal function. Wide voltage and high power motors for general use. Standard heat sink, easy to use. Specification: Material: Electronic component Color: As shown Size: About 63 x 45 x 27 mm Working voltage: 5-36V Maximum current: 16A Maximum power: 350W Overcurrent protection: Yes Package includes:     1pc x Motor Controller Note: 1. Due to the light and screen difference, the item's color may be slightly different from the pictures. 2. Please allow 1-2 cm differences due to manual measurement. #Motor #Controller #For #BLDC #Bicycle #Speed #Driver #Board #Easy #Apply #Mini #Professional #Stable #Brushless #E

Precautions: 1. There is no fuse in the power supply circuit on the motherboard. Jianyi has added it himself. Reverse connection of the positive and negative poles of the power supply will cause permanent damage to some of the chips on the board (even if it does not work for 1 second) 2. There is motor blocking protection during normal operation. Please do not artificially short-circuit when the ule is not working normally. Once short-circuiting may cause the line to burst, please use small current and low voltage test for the first wiring test. Matching use of three-phase DC brushless motors with equivalent current and power 3. Do not connect the motor that is obviously inconsistent with the drive ule voltage, current, or power, to avoid inexplicable "nonsensical" damage Product parameters: Product name: Three-phase DC brushless and Hallless drive el: X10 (no sense) Working voltage: 6-20V (limit 5-24V) Drive current: 3A max Maximum speed: 224000 RPM (2 pole motor), 74000 RPM (6 pole motor), 40000 RPM (12 pole motor), 35000 RPM (14 pole motor). Product size: length 34MM x width 27MM x height 11MM Weight: X10 8g (including wire) Interface Description: 1. U V W phase line output is connected to the motor 2. VCC GND main power supply (external DC power supply) Features: This driver is a low-power fan brushless driver, and it can also be embedded in other systems. It is specially used for air pumps, water pumps, oil pumps, fans, etc. and industrial control electric gadgets for small space and low-power DC three-phase brushless motors. Default The middle timing is not suitable for high-power motors, such as long-term full load current operation, Jianyi plus fan cooling colour:Black Material:Plastic, metal Package Contents: 1 x Motor Speed ControllerOnly the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

【FOR】DC 5V-12V 2A 15W brushless motor speed controller no hall bldc driver boardSpecifications: Working Voltage: DC 5V-12V (MAX. 15V) Working Current: 1.5A (MAX. 2A) Maximum Rated Power: 15W Static Current: 0.005A (Stand by) PWM Duty Cycle: 10000 RPM Board Size: 30x25mm/1.18x0.98" Note: Please allow 1-3mm error due to manual measurement. pls make sure you do not mind before you bid Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you! No Retail Package Package Includes: 1 x DC Motor Drive

Interface Description:MA MB MC phase line output motor;5V GND motherboard with its own power supply (current does not exceed 30 mA);VDC GND main motor power supply (external DC power supply);SC speed pulse signal output;Control interface forward and backward (can also drive external switch);VR speed signal input (the integrated potentiometer speed control can also be connected to the external 0-5V speed control;brake Overheat protection: Yes (more than 100, half the power is reduced) Maximum speed: 224000 RPM (2-pole motor), 74000 RPM (6-pole motor), 40000 RPM (12-pole motor), 35000 RPM (14-pole motor) Motherboard specifications: Product Name: 380W Brushless DC Motor Driver Operating voltage: 6.5-50V Maximum current: Nominal peak from 16 to 20A Maximum power: 380 W Overcurrent protection: no (external fuse required) Blocking protection: Yes (the current will be lowered automatically after blocking) Colour:yellow Material:plastic Size:length 63 MM * width 45 MM * height 30 MM Package Contents: 1*Motor controller board Precautions: 1. The power circuit of the main board has no fuse, and the built-in self-addition will cause the board chip to be permanently damaged (even if it is 2 seconds). 2. During normal operation, there is a sampling overcurrent protection at the motor output. Since the power and current of the ule are very large, do not short circuit when the ule does not work normally. Once the short circuit has the possibility of burning the line, the first wiring test machine uses low current and low voltage, after ok, high current and high voltage passes, because it is a bare board ule for sale , pay attention to the wiring line insulation, strong voltage is not allowed to touch the board parts. 3. Do not connect the motor that is clearly inconsistent with the voltage and current of the drive ule or that is far from each other. Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

Description: 100% brand new and high quality! MA MB MC phase line output connection motor. VCC GND external DC power supply line. Full patch process, stable performance, with positive and negative reversal function. Wide voltage and high power motors for general use. Standard heat sink, easy to use. Specification: Material: Electronic component Color: As shown Size: About 63 x 45 x 27 mm Working voltage: 5-36V Maximum current: 16A Maximum power: 350W Overcurrent protection: Yes Package includes:     1pc x Motor Controller Note: 1. Due to the light and screen difference, the item's color may be slightly different from the pictures. 2. Please allow 1-2 cm differences due to manual measurement. #Motor #Controller #For #BLDC #Bicycle #Speed #Driver #Board #Easy #Apply #Mini #Professional #Stable #Brushless #E

Description: 100% brand new and high quality! MA MB MC phase line output connection motor. VCC GND external DC power supply line. Full patch process, stable performance, with positive and negative reversal function. Wide voltage and high power motors for general use. Standard heat sink, easy to use. Specification: Material: Electronic component Color: As shown Size: About 63 x 45 x 27 mm Working voltage: 5-36V Maximum current: 16A Maximum power: 350W Overcurrent protection: Yes Package includes: 1pc x Motor Controller Note: -Due to the light and screen difference, the item's color may be slightly different from the pictures. -Please allow 1-2 cm differences due to manual measure