Kí hiệu điện trở

A designed according to the principle of ohm's law and through the resistor in parallel through a different switch, can produce 3 kinds of resistance of a new USB electronic load resistance discharge, when all the switch opens, is 2.2 ohm/10W, 4.7 ohm/10W, 2 kinds of resistance in parallel at the same time, in 5V voltage almost can produce 3A discharge current. The actual current size, please according to ohm's law: I = U/R Resistor in parallel calculation formula: R=1/(1/R1+1/R2+...+1/Rn) K1=4.7Ohm/10W , K2=2.2Ohm/10W Load device is working, winding resistance caused by large current, will produce very, very high temperature, therefore in the process of use, and just use the finished in a short period of time, absolutely can't human exposure golden metal radiator parts, to avoid the scald!Nor to flammable items contact tester, in order to avoid the fire!In use process must be highly vigilant! Considering the particularity of heat resistance, the initial use of electricity after a period of time will appear a few white smoke and smell, because outside the paint contains very little moisture, high temperature electric heating, moisture evaporates form the phenomenon of white smoke, produce peculiar smell by high temperature baking paint outside phenomenon, completely disappear after using for a period of time.This phenomenon is inevitable, belongs to the normal situation, do not have to worry about load tester can damage, please be assured that use Load application: Can be convenient to test mobile power charging treasure, mobile phone charger, USB power output current is such as to amount to mark, so long as connect USB above.And can do it for mobile power supply and USB power adapter aging test, aging test discharge resistance will be hot, temperature is controlled in 80 ~ 85, please pay attention to prevent hot Size: 6.5x2.2cm/2.56x0.87inch Quantity: 1 Pc Note: Please allow 1-3mm error due to manual measurement. pls make sure you do not mind before you bid Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you! Package Contents: 1 x USB Tes

Xuất xứ: USA Hướng dẫn sử dụng: Dùng trực tiếp Bảo quản: Bảo quản nơi khô ráo thoáng mát Bao bì sản phẩm có thể thay đổi theo Nhà cung cấp Sản phẩm được nhập khẩu trực tiếp Nguyên liệu được chọn lọc kĩ lưỡng, đem đến hương vị thơm ngon Quy trình sản xuất hiện đại nhập khẩu từ nước ngoài Đóng gói tiện lợi, đẹp mắtHạn sử dụng: 2 năm kể từ ngày sản

Hello! Nice to meet you! Welcome to our shop! Check out our shop daily for the latest products We are an ethical business where prices are always affordable and reasonable No worries! You are guaranteed to be satisfied with the quality of our products It is checked rigorously multiple times before it reaches you Feel free to contact us if you have any questions Have a nice day and don’t forget to give us 5 stars if you enjoy your product Thank you for visiting! Hope you have an outstanding shopping experience! Pontensio for machines and other devic

Item Type:DECODER el Name:LED Turn Signal Light Decoders Voltage:DC 12V Power:21W Resistance:10 Ohm Best Choice for Motorcycle Motorbike Scooter Quad Cruiser Harley Kawasaki Yamaha Suzuki Off Road Slows Down the Flash Rate when Switching from Bulb to LED Indicators, Eliminates the Need to Replace the OE Relay High Temperature Resistant Wire, Longer Service Life, Compatible with More els Connectors for Easy Installation, Fitted to LED Indicators/Flasher/Turn Signal A pair of resistors universal fits for many motorcycle motorbike LED indicators. Helps to soe hyper flash or no blinking of turn signal. Fix blinker flash error, reduces voltage to suitable level. In-line resistors available for bulbs up to 10 and 23 watts. colour:Black & yellow Material:Cement resistance size: 6x1.2cm Wire length: Approx.15cm Package Contents: 2 x decoder / 4 x decoder<br />Only the above package content, other products are not included.<br />Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

Description: 4 Pieces of 50W 6 Ohm Load Resistor for Auto LED lighting lamp. Solution for "bulb out signal" / "OBC error message" after installing SMD LED light bulb. Solution for Fast Turn Signal Blinking response after installing SMD LED light bulb. Each LED bulb installation requires one resistor connected in parellel. It works as warning canceller, decoder, capacitor, or blinker rapid Flash Equalizer for LED light bulb such as 1156, 1157, 3156, 3157, 7440, 7443 or etc. Specification: Item type: Load Resistors Power: 50W Resistance: 6ohm Allowable deviation: ±5％ Temperature coefficient: PTC Material: Alloy Installation: Just connect the wires with the splice taps provided and no wire cutting is necessary. Note: Load Resistors heat up like light bulbs and get really HOT when working. Mount them on metal surface, NOT plastic. Package included: 4Pcs 50W 6ohm Load Resistors 8Pcs T-Taps Please contact us first when you have any problem,we will give you the best service and solve the problem ASAP.Thank you so

{MT1VN}Features - Brand New and high quality; - Can be used with vehicle turn signal lights's LED conversion; - Solve hyper flash or no blinking of turn signal; - Each LED bulb installation requires one resistor connected in parellel(see picture below for instruction); - Solution for "bulb out signal" / "OBC error message" after installing SMD LED light bulb - Solution for fast turn signal blinking response after installing SMD LED light bulb Specifications: Item Type: One LED resistor is required for each turn signal bulb or each license plate light bulb. Color:Yellow(As pictures show) Quantity: 1Pcs Size(L*W):5cm*2cm/2in*0.8in Material:Aluminum Package Included:1Pcs 50W 6 ohm LED Load Resistors Note: 1.Please allow 0.1-0.3cm differences due to manual measurement, thanks. 2.Please understand because of the light irradiation or computer display difference, so I can't guarantee photos and real color is 100% the

Features: *50W 6 Ohm LED Light Decoder Load Resistor for Fix LED Bulb Fast Hyper Flash Turn Signal Blinker *Used in the LED car taillights, frequency converters, automobile brake equipment, large power supply, industrial control equipment etc. *Used to fix blinker flash error, hyper or error flashing of LED turn signal, parking/driving running light or license plate light *Applied to adjust the flashing speed of the LED light *Can be used as warning canceller, decoder, capacitor, or blinker rapid flash equalizer for LED light bulb such as 1156, 1157, 3156, 3157, 7440, 7443 etc. *Compact size, high power and high precision *Using professional technology to seal, stronger and more resistant to heat *Resistance to damp, anti-vibration, explosion proof *With wire at each end of the resistor and T-Taps for easy installation *Suitable for cars, trucks and SUV *100% brand new and high quality Specifications: *Color: Golden (As Pictures Show) *Power: 50W *Resistance: 6 Ohm *Dimension: 50*22*17mm/1.97*0.9*0.6 inch (Approx.) *Quantity: 4pcs Package Contents: 4pcs Load Resistors 8pcs T-Taps　 Note: The real color of the item may be slightly different from the pictures shown on website caused by many factors such as brightness of your monitor and light brightness. #LoadResistors &nbsp;#Decoder &nbsp;#4pcs &nbsp;#50W &nbsp;#6Ohm &nbsp;#LED &nbsp;#Bulb &nbsp;#Fast &nbsp;#Hyper &nbsp;#Flash &nbsp;#Blinker &nbsp;#TurnSignal &nbsp;#Lights &nbsp;#Golden &nbsp;#Cars &nbsp;#Trucks &nbsp;#equipment &nbsp;#CarAccessories &

Điện trở đốt, điện trở đun nước, điện trở sấy thanh gia nhiệt Điện trở đốt, điện trở đun nước, điện trở sấy Điện trở đốt, điện trở đun nước, điện trở sấy, điện trở nhiệt, điện trở cho lò nướng, điện trở ra một đầu, điện trở 3 pha, 1 pha, điện trở xả biến tần. Điện trở đốt được làm từ các dây hợp kim có điện trở suất cao và chịu được oxy hóa ở nhiệt độ c

_______♤Welcome to【caoyuan】Store♤___________ ✔Ready Stock !! Buy Now !！ ✔Quality Checked ✔Best price ✔Support COD ✔Brand new 100% ✈Shipping in 24 Hours ✔Actual items are the same as pictures shown on the page. ★Surprises for you★ ☛Free Gifts: Follow Us+❤ ✌(Tip:We will be based on your guests in your country to send the corresponding adapter plug) __________________❀Product Information❀__________________ Features: 2pcs high quality LED Decoder Wirewound Load Resistors. Clear OBC and CAN bus warning errors on the instrument panel while installing LED bulbs. Solve the hyper flash/blink problem of installing LED bulbs and LED indicators. Premium plastic and metal material, large resistance, long service life. Easy to install, plug and play without making wiring modification. Perfectly suitable for car LED bulbs of headlights, fog lights, or daytime running lights. Specifications: Condition: Brand New Material: Metal + plastic Color: Shown as picture Power: 25W Resistance: 25Ω Package Weight: Approx.45g/1.6oz Package List: 2 * LED Decoders 1 * Acceesory Set Note: The load resistor will become very hot in use. Please carefully install. Don't put them near anything that might melt, such as wires, plastics, etc. Than

#One #Pair #Cement #Load #Resistors #For #Motorcycle #LED #Turn #Signal #Indicator #Light 100% brand new and high quality Features: A pair of resistors for most of motorcycle motorbike LED turn signal indicators. Helps to solve LED related turn signal problems such as hyper flashing, no flashing or burnt out bulb indications. Fix blinker flash error, reduces voltage to suitable level. Each LED turn signal required one resistor, but some motorcycles might require more than one per indicator depending on the original wattage and other aftermarket LED indicators/ resistors fitted. Made of high quality materials, these in-line resistors are durable and can be used for a long time. Specification: Voltage: DC 12V Power: 10W Resistance: 10 Ohm Material: Cement resistance Dimensions: 5x1cm/1.97x0.39inch Color: Black & red Quantity: 2 Pcs Note: 1.Please allow 0-1cm error due to manual measurement. pls make sure you do not mind before you bid. 2.Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you! Package includes: 2 x Resi

Product Properties Brand Name : JIUWAN Item Type : DECODER Socket Type : H1 Model Name : 25W Color Temperature : 8000K Specifications: Condition: 100% brand new,high quality Product Name: Load Resistors for LED Turn Signals Condition: 100% brand new,high quality Easy to Install.Plug & Play. Fix too fast flashing.Fix No flashing. 2 pcs Load Resistors with 8 pcs wire Clip Features: This is 2 pcs 6 Ohm 25W LED Load Resistors for LED Turn Signal Light Fix or LED License Plate Lights Error Fix. These 6 Ohm, 50 Watt LED load resistors will work on any vehicle and can be connected across the turn signal bulbs or License Plate Lights to simulate the load of a regular filament bulb (2 Amp load). This will solve LED related turn signal lights or license plate light problems such as hyper flashing, no flashing or burnt out bulb indications. One LED resistor is required for each turn signal bulb or each license plate light bulb. Applications: - Can be connected to turn signal light, to fix light problems such as hyper flashing, no flashing or burnt out bulb indications. Package included: 2 X 25W Load Resistors 8 X Quick wire Clip If you have any difficulties in shopping, you can contact us at any time. We will answer for you and provide more perfect service. Let every buyer have pleasant shop

Description: 4 pieces LED turn signal resistors Use at wrong flashing frequency. 27 Ohms, 21 Watts Suitable for many LED mini indicators, including for Kellermann etc. Applicable: motorcycle Item type: LED Resistors Cable Material: Plastic Color: As pictures. Size: 15 cm  Package includes: 4x LED Resistors Cables Notes:  1. Due to the different monitor and light effect, the actual color of the item might be slightly different from the color showed on the pictures. Thank you!  2. Please allow 1-3cm measuring deviation due to manual measurement. #LED #Resistors #Cable #4pcs #Motorcycle #Accessories #Decoder #For #Indicators #Repair #Lightweight #Durable #Portable #Turn #S

Features: Can be used with LED turn light of cars, bikes Excellent heat dissipation Stop bulbs blowing Correct too-fast flashing Power: 25w Resistance: 6.8 Ohm Voltage: 12v Dimension: approx. 1.7 x 1.5cm / 0.67 x 0.59 inch Cable Length: approx. 35cm / 13.78 inch Note: Please be the LED load resistor will be very hot and work in high temperature; Do Not mount on plastic or material with low heat resistance  Package Includes: 1 x Resis

TẤT CẢ SẢN PHẨM CỦA SHOP ĐỀU LÀ HÌNH THẬT VÀ HÀNG THẬT, LUÔN LUÔN CÓ SẴN TRONG KHO, TẤT CẢ CÁC MẶT HÀNG ĐỀU ĐƯỢC BẢO HÀNH VÀ ĐỔI TRẢ TÙY THEO ĐIỀU

___________________❀HAAPEURY❀___________________ Welcome to our store, we insist on to sell the best quality items. ✔Ready Stock ✔ ✔Quality Checked ★Surprises for you★ ☞Shop Voucher: Get More Discount ☞Follow Shop: Free Gifts ★★Attention Please★★ ✌We will be based on your guests in your country to send the corresponding adapter plug. _______________❀Product Information❀______________ Feature: -Made of high-quality materials, antirsut and corrosion resistant, durable and practical. -With screw holes that can be used to fix the resistor on the chassis or heat sink for greater heat dissipation. -Widely used in power supply, sensor, elevator, stage audio and high demand equipment industry. -Advanced manufacturing technology, high reliability and high performance. -Built to meet standard specification, strictly follow factory quality control. Specification: Condition: 100% Brand New Item Type: Resistor Color: As picture shown External Material: Aluminum Resistance Value: 10Ohm 10R Rated Power: 200W Endurance: ± 5% (J) Mounting Hole Diameter: Approx. 4.2mm/0.2in Hole to Hole Distance: Approx. 41.5mm(1.6in) / 37.5mm(1.5in) Board Size (Length x Width x Height): Approx. 100 x 52 x 29mm/3.9 x 2 x 1.1in Body Size (L x D): Approx. 100x32mm/3.9 x 1.3in Package List: 1 x 200W 10R Res

Features: Used against fast flashing and onboard error lights. It can be used with LED conversion of vehicle turn signal light. Resolve hyper flash or no blinking of turn signal. Each LED bulb installation requires a resistor in parallel. Solution for bulb blackout signal/OBC error message after installing SMD LED bulbs. Solutions for fast turn signal blinking response after installing SMD LED bulbs. These resistors will get hot, so install it properly on metal. If the error lights still exist, some cars will need two on each side under strange circumstances. Specification: 100% brand new with high quality Color: As pictures show To Fit: Lights error Free Package Included: 2 pcs 25w resistors + 4 pcs scotch locks Note: -The colors may be a little difference for the different monitor display. Please check as much as possible to make sure the item is the one that you need. -Please allow 0.5-1 inch difference due to manual measurement.(1inch=2.

Item Details: *BA15S P21W 1156 LED Bulb OBC Warning Canceller Decoder Load Canbus Resistors *Ideal for solving bulb warning messages on vehicles with a canbus system *Can take the leftover voltage after fitting an LED and bridge the resistance gap between an LED and a traditional Halogen bulb, thus, no errors *Suitable for DRLs, Foglights, Rear Lights etc. *Easy to use, plug and play *100% brand new and high quality *Color: As Pictures Show *Power: 50W Warm Tips: 50W load resistors do get hot so please be ensure that they are mounted safely Package Contents: 2pcs 50W Load ResistorDecoders Note:The real color of the item may be slightly different from the pictures shown on website caused by many factors such as brightness of your monitor and light bright

12V 2 Pin Speed Adjustable LED Indicator Flasher Turn Signal Light Relay Resistor Fix Hyper Control Flash for Motorcycle Orange Color This Flasher Relay will solve LED related turn signal indicator problems such as hyper flashing, not flashing, or bulb out warning message on dashboard indicator or just replace a failed relay.  Features:  Eliminate the need for tapping wires to install the load resistors. 2-pin Electronic LED Flasher is also speed adjustable, allow LED bulbs to blink at the normal rate. Can use a flat head screw driver to adjust the knob on the bottom to set its flashing speeds from 50c/m to 200c/m.  Easy Plug & Play installation on most motorcycles. Efficient unit with no excess heat issue. Specifications: Color: orange  Quantity: 1 pcs Voltage: 12V Max power: 45.4W Switch load: 0.1W-45.4W (0.02A ~ 10A) Flashing frequency: 50 to 200 times per min Operating temperature: -40°C to + 80°C Adjustable flashing speed: clockwise (slower); counter clockwise (faster) Item size: 35 * 35 * 25mm / 1.38 * 1.38 * 0.98in Package size: 35 * 28 * 50mm / 1.38 * 1.10 * 1.97in Package weight: 17g / 0.60oz Note: This LED flasher relay works plug & play on most motorcycles with standard 2-Pin flasher relays. Package List:  1 * 2-Pin Flasher

Máy thử tải điện tử có tuổi thọ cao cấp công nghiệp sử dụng quạt bóng có tuổi thọ cao, tốc độ quay nhanh và gió mạnh. Nó hỗ trợ xả liên tục cho công việc không ngừng và thích hợp cho xả trong thời gian dài hoặc nhà máy thực hiện kiểm tra lão hóa cho sản phẩm. Nó phù hợp để kiểm tra khả năng hiện tại của bộ sạc, kiểm tra độ già của bộ sạc, đo dung lượng tải của pin, v.v. Nó có thể được sử dụng như tải điện tử thông thường, cũng có thể sử dụng tải điện tử USB, sử dụng màn hình tinh thể lỏng, giao diện máy tính thân thiện và các chỉ số hiệu suất tuyệt vời, Đáp ứng nhiều nhu cầu thử nghiệm. Đặc trưng: Hỗ trợ tản nhiệt Độ chính xác cao Màn hình LCD HD Hỗ trợ bảo vệ kết nối ngược Hỗ trợ bảo vệ quá áp Hỗ trợ bảo vệ quá dòng Hỗ trợ bảo vệ dưới điện áp Hỗ trợ bảo vệ quá nhiệt Hỗ trợ bảo vệ quyền lực Nhiều tham số được hiển thị đồng thời Hỗ trợ chức năng bộ nhớ giảm điện Hỗ trợ chức năng báo thức Tự động đếm giờ làm việc Hiển thị điện áp đầu vào / hiện tại / nguồn Thời gian xả / Công suất xả / Nhiệt độ Thông số: Tên sản phẩm: FX25 FX35 Thiết bị kiểm tra tải điện tử Mẫu: FX25 FX35 Điện áp làm việc: DC 5V Tải điện áp: DC 1.5V-25V Điện áp làm việc: dưới 200mA Tải hiện tại: 4A / 5A Công suất: 25W / 35W Độ chính xác hiện tại: 1% Độ chính xác điện áp: 1% Phương pháp tản nhiệt: Quạt + Nhôm tản nhiệt Bảo vệ quá điện áp: Mặc định 25,5V (Có thể điều chỉnh) Bảo vệ quá mức: Mặc định 4.10A (Có thể điều chỉnh) Bảo vệ quá mức: Mặc định 25,5W (Có thể điều chỉnh) Dưới bảo vệ điện áp: Mặc định 1.5V (Có thể điều chỉnh) Bảo vệ quá nhiệt: Mặc định 80 ° (Có thể điều chỉnh) Tốc độ quạt: 6000RPM +/- 10% Nhiệt độ làm việc: -40 ° ~ 85 ° Độ ẩm làm việc: 0% ~ 95% rh Kích thước: 114 * 43 * 27mm Chức năng: Hiển thị dòng điện A, điện áp V, công suất W, công suất Ah và thời gian phóng điện Cơ chế bảo vệ hoàn hảo Tự động đếm công suất xả và thời gian xả Hỗ trợ cài đặt công suất phóng tối đa (OAH) và thời gian xả tối đa (OHP). (Đạt được kiểm tra lão hóa công suất) Quạt điều khiển nhiệt độ thông minh. Quạt tự động khởi động khi công suất lớn hơn 10W hoặc nhiệt độ lớn hơn 40 ° Chiết áp xoay để điều chỉnh dòng chính xác đến 0,01A Bộ rung bắt đầu báo động và đèn LED sẽ nhấp nháy khi vào chế độ bảo vệ. Chế độ bảo vệ: Mô-đun vào chế độ bảo vệ khi tham số tải vượt quá giá trị đặt. Nút bấm ngắn ‘BẬT / TẮT 'có thể thoát khỏi chế độ bảo vệ. Sử dụng các bước: Kết nối tải và điện áp làm việc. Đặt tham số đúng như thiết lập thủ công. Kiểm tra và sử dụng. Ứng dụng: 1. Tải thử nghiệm 2. Kiểm tra vòng tròn 3. Kiểm tra xả thải 4. Kiểm tra thiết bị 5. Tải trọng thông thường 6. Kiểm tra lão hóa cung cấp năng lượng 7. Đo lường chất lượng của cáp sạc Micro USB 8. Đo lường chất lượng của các dòng sạc loại c 9. Bộ sạc đo lường bổ sung Khả năng hiện tại 10.Charger Factory Batch Aging sử dụng thử n

Specifications: Cable length: about 10cm Color: Black If 5w lamps were installed as standard, you only need 1 x resistor per side of the vehicle For 10W lamps installed as standard or before the conversion, you need 1 x resistor per turn signal, Package Included: 2x Signal Indicator Decoding Resistance Wire Notes: The colors may be a little difference for the different monitor display. Please allow minor deviation due to manual measure

Description: Wattage: 10W Resistance: 10 ohm Input voltage: 12V Application: LED Turn Signal indicator Light Fitment: universal for most motorcycles,such as for Yamaha, for Honda, for Suzuki,for Kawasaki, -Davidson for Ducati, for Buell, For Aprilia, for Triumph etc. Package include: LED Turn Signal Decoder Note: ONLY fit for motorcycle LED Turn Signal Indicator Light, NOT fit for other

Features: Durable Material: The shell is made of ABS material, which is not easy to deform, durable. Quick Installation: Pre-wired for plug-and-play. No need to modify the stock wires at all.Just need simply several steps for its complete installation. Main Function: Helps to solve LED related braking signal light problems such as hyper flashing, no flashing or burnt out bulb indications to ensure the led bulbs light up without malfunction issue or flickering issue. Use Range: This can be installed on 3157B LED brake lights with no annoying rapid flashing nor error message code on your car dashboard. Replacement Parts: It can replace the old or damaged one perfectly. Specifications: Item type: LED load resistor Material: ABS shell Color: Black Socket type: 3157B Voltage: DC12V Working power: 8W Cable length: About 27cm Package includes: 1Pc x LED load resistor Notes: Transition: 1cm=10mm=0.39inch -Due to the different monitor and light effect, the actual color of the item might be slightly different from the color showed on the pictures. Thank you! -Please allow 1-3cm measuring deviation due to manual measure

Features: *50W 6 Ohm LED Light Decoder Load Resistor for Fix LED Bulb Fast Hyper Flash Turn Signal Blinker *Used in the LED car taillights, frequency converters, automobile brake equipment, large power supply, industrial control equipment etc. *Used to fix blinker flash error, hyper or error flashing of LED turn signal, parking/driving running light or license plate light *Applied to adjust the flashing speed of the LED light *Can be used as warning canceller, decoder, capacitor, or blinker rapid flash equalizer for LED light bulb such as 1156, 1157, 3156, 3157, 7440, 7443 etc. *Compact size, high power and high precision *Using professional technology to seal, stronger and more resistant to heat *Resistance to damp, anti-vibration, explosion proof *With wire at each end of the resistor and T-Taps for easy installation *Suitable for cars, trucks and SUV *100% brand new and high quality Specifications: *Color: Golden (As Pictures Show) *Power: 50W *Resistance: 6 Ohm *Dimension: 50*22*17mm/1.97*0.9*0.6 inch (Approx.) *Quantity: 4pcs Package Contents: 4pcs Load Resistors 8pcs T-Taps Note: The real color of the item may be slightly different from the pictures shown on website caused by many factors such as brightness of your monitor and light brightness. Note: Các sản phẩm có chất liệu vàng, kim cương, đá quý trong shop đều là xi mạ/ nhân

Features: This is 1 pair (2 pieces) of 50W 6-ohm load resistors for 1157 led bulbs with wire adapters. This load resistor fix Switchback LED error code or fast blinking issues related to the low current draw For turn signal light with no annoying rapid flashing nor error message/code on your car dashboard. Specification: Material: ABS+metal Color: black gold (the color of the line is random) Voltage: 12V Power: 50W Resistance: 6Ω Color temperature: 6000K Size: total length 70cm+/-5cm Weight: 163g Product list: 2PCS *BAY15D 1157 led decoder Note: 1.Due to the manual measurement and different measurement methods, the actual size could be slightly different. 2.Please be reminded that due to lighting effects and monitor's brightness/contrast settings etc, the color tone of the website's photo and the actual item could be slightly different. #LEDlightdecoder #FlashErrorCancellers #errorcanceller #LightDecoder #led #decoder #CarLightDecoder #HyperFlashCanceller #FlashCanceller #lights #LEDlightdecoder #FlashErrorCancellers #gadget #LightDecoder #led #decoder #CarLightDecoder #HyperFlashCanceller #FlashCanceller #li

Đặc điểm: Mới 100% chất lượng cao. Nó có thể được sử dụng với sự chuyển đổi LED của xi nhan xe Giải quyết vấn đề đèn xi nhan siêu nhấp nháy hoặc không nhấp nháy Mỗi lần lắp đặt bóng đèn LED yêu cầu một điện trở được kết nối song song Đã sửa lỗi nhấp nháy đèn flash, đèn xi nhan LED, đèn đỗ xe/đèn lái xe hoặc đèn biển số xe chạy quá tốc độ hoặc nhấp nháy sai Nó phù hợp với bộ hủy cảnh báo, bộ giải mã, tụ điện, bộ cân bằng nhanh flash, v.v. của bóng đèn LED 1156, 1157, 7440, 7443, v.v. Thông số kỹ thuật: Chất liệu: Hợp kim Màu sắc: vàng và đỏ Số lượng: 2 chiếc Gói thầu bao gồm: 2 kháng tải 4 vòi hình chữ

Package:2pcs led bulbs Just For Turn Signal Lights No Resistor No Hyper Flash, Canbus Product Description: Suitable for most kinds of cars . Compatible with:Turn Signal Lights Feature: -Brand Name:VENDY -Non polarity -LED Chip Type:54/72 SMD 3030 Chip -LED colour: Amber -Socket type: PY21W/P21W/BAU15S/BA15S/7507/7506/T20/WY21W/W21W/7440 -Voltage:DC12V -Power:18W -Luminous flux:3600LM -Material: Aluminum -Lifespan: 50000 hours Low temperature, low power consumption Add style and brighten your vehicle. Super bright LEDs are much brighter than original incandescent bulbs. Installs easily in just minutes - no tools ne

Features: Durable The shell is made of high temperature resistant material, highly efficient and flame retardant, durable; the design is upscale and generous Easy to install The structure design is more reasonable and the installation is more convenient; Safe The resistor has positive and negative function protection Practical It is mainly used for retrofitting LEDs. The halogen lamp of the original car has high power. However, due to the low LED power, the computer driving system of the original car has a fault display, which can be eliminated after installation. Scope of application It is mainly used for the modification of small lights such as fog lights, turn signals, indicator lights and so on. Specification: Type: led decoder Quantity: 4pcs Material: high temperature resistant material Color: as show Input start current: 6A Power: 50w Light source: led Net weight: 140g/ 4.94oz Package: 4* led de

Features: Durable Material: The shell is made of ABS material, which is not easy to deform, durable. Quick Installation: Pre-wired for plug-and-play. No need to modify the stock wires at all.Just need simply several steps for its complete installation. Main Function: Helps to solve LED related braking signal light problems such as hyper flashing, no flashing or burnt out bulb indications to ensure the led bulbs light up without malfunction issue or flickering issue. Use Range: This can be installed on 3157B LED brake lights with no annoying rapid flashing nor error message code on your car dashboard. Replacement Parts: It can replace the old or damaged one perfectly. Specifications: Item type: LED load resistor Material: ABS shell Color: Black Socket type: 3157B Voltage: DC12V Working power: 8W Cable length: About 27cm(with LED decoder) Package includes:  1Pc x LED load resistor Notes:  Transition: 1cm=10mm=0.39inch  1. Due to the different monitor and light effect, the actual color of the item might be slightly different from the color showed on the pictures. Thank you!  2. Please allow 1-3cm measuring deviation due to manual measurement. #LED #Load #Resistor #Anti #Hyper #Blinking #Error #Canceller #Car #Brake #Light #Adapter #Turn #Signal #Flashing #Truck #Taillight #Replac

Package:2pcs led bulbs Just For Turn Signal Lights No Resistor No Hyper Flash, Canbus Product Description: Suitable for most kinds of cars . Compatible with:Turn Signal Lights Feature: -Brand Name:VENDY -Non polarity -LED Chip Type:54/72 SMD 3030 Chip -LED colour: Amber -Socket type: PY21W/P21W/BAU15S/BA15S/7507/7506/T20/WY21W/W21W/7440 -Voltage:DC12V -Power:18W -Luminous flux:3600LM -Material: Aluminum -Lifespan: 50000 hours Low temperature, low power consumption Add style and brighten your vehicle. Super bright LEDs are much brighter than original incandescent bulbs. Installs easily in just minutes - no tools ne