Ir arduino

Điện áp cung cấp: Số mô hình:Obstacle Avoidance Sensor Module tản điện:.. is_customized:Vâng Nhiệt độ hoạt động:.. điều kiện:Mới loại:Integrated circuit module ứng dụng:Integrated circuit m

[Trillionca] 5PCS IR Infrared Obstacle Avoidance Sensor Module For Arduino Smart Car Robot************************Welcome to our Trillionca***********************Description: -When the module detects an obstacle in front of the signal , the green indicator light on the board level , while low-level continuous output signal OUT port , the module detects the distance 2 ~ 30cm, detection angle 35 °, the distance can detect potential is adjusted clockwise adjustment potentiometer to detect the distance increases ; counterclockwise to adjust the potentiometer to reduce the detection distance . 2 .active infrared sensors to detect the reflected , and thus the shape of the reflectivity of the target detection range is critical . The minimum detection distance which black , white maximum ; small objects from a small area , a large area from the Grand . 3 . the output port OUT sensor module can be directly connected to the microcontroller IO port , you can directly drive a 5V relay ; Connection : VCC-VCC; GND-GND; OUT-IO 4 .using the comparator LM393, stable ; 5 .can be used for 3-5V DC power supply modules . When the power is turned on, the red power indicator light ; -with the screw holes of 3mm , easy fixed installation ; -board size : 3.1CM * 1.5CM Interface Description (3-wire): -VCC: external 3.3V-5V voltage (can be directly connected to 5v MCU and 3.3v MCU) -GND: GND External -OUT: small board digital output interfaces (0 and 1) Package Include:5 x Infrared obstacle avoidance m

Thời gian giao hàng dự kiến cho sản phẩm này là từ 7-9 ngày Set 5 module cảm biến hồng ngoại IR tránh chướng ngại vật 3 dây phản quang cho xe hơi robot Arduino Mô tả mô-đun Mô-đun cảm biến thích ứng với ánh sáng xung quanh, có một cặp ống phát và nhận hồng ngoại, ống truyền phát ra tần số hồng ngoại nhất định, khi phát hiện hướng của vật cản (bề mặt phản xạ), tia hồng ngoại được ống tiếp nhận, Sau khi Xử lý mạch so sánh, đèn xanh lá bật, nhưng giao diện đầu ra tín hiệu tín hiệu số (tín hiệu mức thấp), bạn có thể điều chỉnh chiết áp núm khoảng cách phát hiện, phạm vi khoảng cách hiệu dụng 2 ~ 30cm, điện áp hoạt động 3.3V - 5V. Phạm vi phát hiện của cảm biến có thể thu được bằng cách điều chỉnh chiết áp, ít nhiễu, dễ lắp ráp, dễ sử dụng, có thể được sử dụng rộng rãi trong việc tránh chướng ngại vật robot, tránh xe, định vị làn đường và theo dõi đường đen trắng v.v . Thông số mô-đun 1, Khi mô-đun phát hiện chướng ngại vật phía trước tín hiệu, đèn chỉ báo màu xanh lục ở trên bảng, trong khi cổng OUT duy trì đầu ra tín hiệu thấp, mô-đun phát hiện khoảng cách 2 ~ 30cm, góc phát hiện 35 °, khoảng cách có thể phát hiện tiềm năng là điều chỉnh chiết áp theo chiều kim đồng hồ, phát hiện tăng khoảng cách; chiết áp điều chỉnh ngược chiều kim đồng hồ, giảm khoảng cách phát hiện. 2, cảm biến phát hiện phản xạ hồng ngoại chủ động, độ phản xạ mục tiêu và hình dạng, khoảng cách phát hiện. Trường hợp khoảng cách phát hiện tối thiểu sẽ hiển thị màu đen, tối đa - màu trắng; các vật thể nhỏ cách xa một khu vực nhỏ, một khu vực rộng lớn từ trên cao. 3, cổng đầu ra mô-đun cảm biến Cổng OUT có thể được kết nối trực tiếp với vi điều khiển IO cũng có thể được điều khiển trực tiếp rơle 5V; Kết nối: VCC-VCC; GND-GND; NGOÀI 4, so sánh LM393, ổn định; 5, mô-đun có thể được cung cấp điện 3-5V DC. Khi bật nguồn, đèn báo nguồn màu đỏ sẽ sáng; 6, với các lỗ vít 3 mm, lắp đặt cố định dễ dàng; 7, kích thước bảng: 3.2CM * 1.4CM 8, mỗi mô-đun đã được vận chuyển ngưỡng so sánh điện áp điều chỉnh bằng chiết áp tốt, trường hợp không đặc biệt, không điều chỉnh chiết áp. Giao diện Module Mô tả 1. Điện áp ngoài VCC 3.3V-5V (có thể được kết nối trực tiếp với MCU MCU 5v và 3.3v) 2. GND GND bên ngoài 3. Giao diện đầu ra kỹ thuật số bảng nhỏ OUT (0 và 1) Trước khi mua: 1. Tất cả sản phẩm đều có sẵn, chúng tôi sẽ sắp xếp đơn hàng ngay lập tức nếu chúng tôi nhận được đơn đặt hàng. 2. Xin vui lòng đọc mô tả sản phẩm, nếu bạn có bất kỳ câu hỏi nào, đừng ngần ngại liên hệ với chúng tôi. Sau khi mua: 1. Nếu bạn hài lòng hãy cho chúng tôi đánh giá 5 sao. #IR #Infrared #Obstacle #Avoidance #Sensor #Module #for #Arduino #Smart #Car #Robot #3-wire #Reflective #Photoelectric

Welcome to enjoygood2❤ Description： 1. When the module detects an obstacle in front of the signal , the green indicator light on the board level , while low-level continuous output signal OUT port , the module detects the distance 2 ~ 30cm, detection angle 35 °, the distance can detect potential is adjusted clockwise adjustment potentiometer to detect the distance increases ; counterclockwise to adjust the potentiometer to reduce the detection distance . 2 .active infrared sensors to detect the reflected , and thus the shape of the reflectivity of the target detection range is critical . The minimum detection distance which black , white maximum ; small objects from a small area , a large area from the Grand . 3 . the output port OUT sensor module can be directly connected to the microcontroller IO port , you can directly drive a 5V relay ; Connection : VCC-VCC; GND-GND; OUT-IO 4 .using the comparator LM393, stable ; 5 .can be used for 3-5V DC power supply modules . When the power is turned on, the red power indicator light ; 6. with the screw holes of 3mm , easy fixed installation ; 7. board size : 3.1CM * 1.5CM 8. each module shipments comparing the threshold voltage has been adjusted by the potentiometer is good , not exceptional circumstances, do not arbitrarily adjust the potentiometer. Interface Description (3-wire): 1. VCC: external 3.3V-5V voltage (can be directly connected to 5v MCU and 3.3v MCU) 2. GND: GND External 3. OUT: small board digital output interfaces (0 and 1) Package Include:5 x Infrared obstacle avoidance m

Description: Supply voltage: 5 v Working environment: -25 ~ + 85 ° Storage temperature: -30 ~ + 100 ° Wavelength: 940nm Module size: 22mm × 28mm Module weight: 3g Signal type: digital signal Infrared center wavelength: about 850nm-940nm Infrared emission angle: over 20 degrees Infrared emission distance: over 1.3 meters (5 v 38 khz) Double pipe direct start, through the program to carry out waveform modulation With the introduction signal to show the LED, easy to watch the debugging Applicable to infrared communication, infrared remote control Package Included: 1PC*Infrared Transmitter Module IR Infrared Sensor With LED Indicate for Arduino #Infrared #Ar

1set/lot Ir Infrared Transmitter Module Ir Digital 38khz Infrared Receiver Sensor Module For Arduino Electronic Building

Hello everyone, our company is in Shenzhen。we specialize in selling electronic components. When we receive your order, we will process your order within 24 hours. If you order many items, we may need more time to process, it will not be more than 5 days, please be patient. Genaral it need 1-2weeks arrive your hand.if you chat with us , we donot reply you, donot worry , we are try to handle your order.so pls donot cancel o

Description: IR is widely used in remote control. With this IR receiver, the Arduino project is able to receive command from any IR remoter controller if you have the right decoder. Well, it will be also easy to make your own IR controller using IR transmitter. 38KHz IR Receiver Sensor pin definitions : (1) Output (2) Vcc (3) GND Features : 1、Based on the 38KHz IR Receiver Sensor 2、Can be used for remoter control 3、Power Supply : 5V 4、Interface : Digital 5、Modulate Frequency : 38Khz 6、Pin Definitions : (1) Output (2) Vcc (3) GND 7、Can be compatible with Wrobot Digital 38KHz IR Transmitter Sensor Package Include: 1PCS Digital 38KHz IR Receiver For Arduino Compa

Description: -When the module detects an obstacle in front of the signal , the green indicator light on the board level , while low-level continuous output signal OUT port , the module detects the distance 2 ~ 30cm, detection angle 35 °, the distance can detect potential is adjusted clockwise adjustment potentiometer to detect the distance increases ; counterclockwise to adjust the potentiometer to reduce the detection distance . 2 .active infrared sensors to detect the reflected , and thus the shape of the reflectivity of the target detection range is critical . The minimum detection distance which black , white maximum ; small objects from a small area , a large area from the Grand . 3 . the output port OUT sensor module can be directly connected to the microcontroller IO port , you can directly drive a 5V relay ; Connection : VCC-VCC; GND-GND; OUT-IO 4 .using the comparator LM393, stable ; 5 .can be used for 3-5V DC power supply modules . When the power is turned on, the red power indicator light ; -with the screw holes of 3mm , easy fixed installation ; -board size : 3.1CM * 1.5CM Interface Description (3-wire): -VCC: external 3.3V-5V voltage (can be directly connected to 5v MCU and 3.3v MCU) -GND: GND External -OUT: small board digital output interfaces (0 and 1) Package Include:5 x Infrared obstacle avoidance m

Description： 1. When the module detects an obstacle in front of the signal , the green indicator light on the board level , while low-level continuous output signal OUT port , the module detects the distance 2 ~ 30cm, detection angle 35 °, the distance can detect potential is adjusted clockwise adjustment potentiometer to detect the distance increases ; counterclockwise to adjust the potentiometer to reduce the detection distance . 2 .active infrared sensors to detect the reflected , and thus the shape of the reflectivity of the target detection range is critical . The minimum detection distance which black , white maximum ; small objects from a small area , a large area from the Grand . 3 . the output port OUT sensor module can be directly connected to the microcontroller IO port , you can directly drive a 5V relay ; Connection : VCC-VCC; GND-GND; OUT-IO 4 .using the comparator LM393, stable ; 5 .can be used for 3-5V DC power supply modules . When the power is turned on, the red power indicator light ; 6. with the screw holes of 3mm , easy fixed installation ; 7. board size : 3.1CM * 1.5CM 8. each module shipments comparing the threshold voltage has been adjusted by the potentiometer is good , not exceptional circumstances, do not arbitrarily adjust the potentiometer. Interface Description (3-wire): 1. VCC: external 3.3V-5V voltage (can be directly connected to 5v MCU and 3.3v MCU) 2. GND: GND External 3. OUT: small board digital output interfaces (0 and 1) Package Include:5 x Infrared obstacle avoidance m

Với thiết kế nhỏ gọn, dễ dàng sử dụng với Arduino, giúp các bạn có thể phát triển các dự án điều khiển từ xa thông qua tia hồng ngoại được tích hợp sẵn trong một chiếc Remote 17 phím gồm 12 phím số và 5 phím chức năng (Left, Right, Up, Down, OK), dễ dàng kết nối chỉ với 3 đường dây (Nguồn dương, nguồn âm và dây Output tín hiệu) Thông số kỹ thuật: + Mạch thu: IR1838 với tần số 38MHz + Điện áp hoạt động: 3.3 - 5VDC. + Dạng ngõ ra: Digital. + Remote: 17 phím ShopTN.net cam kết với quý khách hàng: + Sản phẩm đúng mô tả (Lưu ý mỗi sản phẩm của ShopTN.net đều có hình ảnh chụp thật) + Giao hàng tận tay + Hoàn tiền 100% nếu sản phẩm lỗi hoặc giao không đúng sản phẩm + Trong quá trình sử dụng nếu có bất kỳ thắc mắc về sản phẩm đội ngũ nhân viên bên ShopTN.net sẽ luôn sẵn sàng hổ trợ quý khách *Hotline: 0353833179 💓 Cảm ơn quý khách đã tin tưởng. Chúc quý khách có một sự trải nghiệm tuyệt vời nhất khi mua sắm tại ShopTN

Module description -working voltage: 3.3-5.5v -the inlet groove coupler sensor is used with a groove width of 5 mm. -sensor slots are stuck, output high level and indicator lights are extinguished without shelter, output is low and light is light. -output form: digital switch volume output (0 and 1) -use lm 393 comparator output, clean input type, good waveform, drive capacity exceeding 15 ma. -fixed bolt hole, easy to installl. Module interface specification (3 line) 1 vcc 3.3v-5v external 2 gnd external gnd 3 do small board digital output interface switch to microcontroller io port 4.Ao: in

Mô đun Cảm biến Hồng Ngoại 3Pin Ir chống Chướng Ngại Vật Dành Cho Xe Hơi Đặc điểm giao diện hai mô-đun Khi module phát hiện chướng ngại vật trước, đèn báo màu xanh từ bảng mạch tiếp tục xuất ra tín hiệu thấp, mô-đun phát hiện khoảng cách 2 ~ 60cm, góc phát 35 °, khoảng cách có thể phát hiện ra tiềm năng điều khiển để điều chỉnh, theo chiều kim đồng hồ, khoảng cách phát triển; Chiết khấu đồng hồ kim đồng hồ ngược chiều, giảm bớt cách phát. 2, Tia phản xạ hồng ngoại chủ động cảm biến, làm đó phản xạ mục tiêu và tạo hình của vật cản. Tối đa đen trắng tối thiểu phát hiện khoảng cách; small area thì object is small, the large area is the object to. 3, đầu cổng ra modul cảm biến có thể được kết nối trực tiếp với IO cổng của bộ điều khiển, cũng có thể điều khiển trực tiếp được đấu nối 5V; Kết nối: VCC-VCC; GND-GND; 4, so sánh sử dụng LM393, ổn định; 5, can be source 3-5V DC for module. Khi bật nguồn, đèn báo nguồn màu đỏ; 6, with lỗ hổng 3 mm để dễ dàng lắp đặt, lắp lại; 7, mạch bảng kích thước: 3.1CM * 1.5CM 8, each module so sánh điện áp có thể điều chỉnh thông qua chiết áp tốt, trường hợp thông thường, không tự động điều chỉnh chiết áp. Đặc điểm giao diện ba mô-đun (3 dây) 1 bên ngoài VCC điện áp 3,3V-5V (vi điều khiển 5v và có thể được kết nối trực tiếp với MCU 3,3v) GND ngoài 2 GND 3 giao diện đầu ra kỹ thuật số nhỏ bảng (0 và 1) Một mô-đun cảm biến phát hiện ngăn cản 2 20 DuPont line 3 Dễ dàng kết

Decription: Feature: The sensor module light is adaptable to the environment, it has a pair of infrared transmitting and receiving tube, tube infrared emit a certain frequency, when detecting direction meet with obstacles (reflecting surface), reflected infrared receiving tube, after the comparator circuit processing, green indicator will light up, at the same time signal output interface to output digital signal (a low level signal), can be through the potentiometer knob adjust the detection distance, effective distance range 2 ~ 30cm, working voltage is 3.3V to 5V. The sensor detection range can be through the potentiometer to adjust and have small interference, easy to assemble, easy to use, etc, can be widely used in robot obstacle avoidance, obstacle avoidance car, line count, and black and white line tracking and so on many occasions. Module parameters: 1. when the module detects obstacles in front of the signal, the green indicator on the circuit board light level and at the same time the OUT port output low level signal, the detection module from 2 ~ 30cm, 35°detection Angle, test distance can be adjusted through the potentiometer, adjustable potentiometer clockwise, the detection distance increases; Counter-clockwise tuning potentiometer, detection distance is reduced. 2. sensors, active infrared reflection detection, therefore the reflectivity and shape of the target is the key of the detection range. White one black detection range, minimum maximum; Small area of the object distance, large distance. 3. the sensor module output port OUT can be directly connected to the microcontroller IO port can, also can drive a 5v relay directly; Connection mode: the VCC - VCC; GND - GND; The OUT - the IO 4. the comparator USES the LM393, working stability; 5. can be used for 3 to 5v dc power to power supply module. When power on, the red power indicator light lit; 6. 3 mm screw holes, easy fixed, installation; 7. circuit board size: 3.2CM*1.4CM 8. each module is shipped already compare threshold voltage through the potentiometer to adjust good, not special circumstances, please do not arbitrarily adjust the potentiometer. Module interface specification 1. VCC voltage is 3.3V to 5V converter (which can be directly connected to 5V single-chip microcontroller and 3.3V) 2. GND external GND 3. OUT of small plate digital output interface (0 and 1) Included: 10 x Sensor M

Battery:CR2025 Button batteries Transmission Distance: up to 8m (depending on the surrounding environment, sensitivity of receiver etc) Effective Angle: 60° Static Current: 3~5uA, Dynamic Current: 3~5mA Remote size: 8.5 x 4 x 0.65cm/3.3 x 1.6 x 0.25inch (L x W x H) Package Included: 1 x HX1838 VS1838 Infrared IR Wireless Remote Control Sensor Module Kit Wish you have a nice shopping

IR Infrared Transmitter Module IR Digital 38khz Infrared Receiver Sensor Module IR transmitter module: Supply voltage: 5V Working environment: -25 ~ + 85 ° Storage temperature: -30 ~ + 100 ° Wavelength: 940nm Module size: 13.7mm × 27.8mm Module weight: 1g Signal type: digital signal Infrared center wavelength: about 850nm-940nm Infrared emission angle: about 20 degrees Infrared emission distance: about 1.3 meters (5V 38Khz) IR receivr modules: 1. Adopt 1838 remote control receiver with high sensitivity 2. Working voltage 5V 3. output type: digital outputs 4. There are 2 fixing holes for easy installation. Aperture 3.1mm 5. with date indicator 6. PCB size: 23.5*21.5mm Wiring instructions: 1.DAT digital output interface 2.VCC 5V DC power supply positive 3.GND 5V DC power supply negative Before purchase: 1.All the goods are ready stock, we will arrange the shipment at once if we receive the order. 2.Please read the item description, if you have any question, do not hesitate to contact us. 3.Use the vouchers for more saving. Shipment： 1.1-2 days to ship(except for the pro-order item) 2.If you have not received the item after 15 days shipment,Please contact us. After purchase: 1.If you are satisfied，please give us 5 stars praise. 2.Please contact us before you are going to give us bad review. We are helpful and will solve the problems. #1set #IR #Infrared #Transmitter #Module #IR #Digital #38khz #Infrared #Receiver #Sensor #M

Flame sensor module / fire sensor module ky-026 red Feature High sensitivity ir receiver Extremely sensitive to wave between 760-1100nm Lamp indicator power supply Lamp indicator output comparator Ao, real-time thermometer voltage signal output Do, high / low electric level signal output Analog quantity output Threshold rollover electric output level Threshold adjustable by potentiometer Detection angle range: About 60 degrees Power supply: 0-15 v dc Hole inner diameter: Approx. 3mm Size (l x w): Approx. 36

Description: -When the module detects an obstacle in front of the signal , the green indicator light on the board level , while low-level continuous output signal OUT port , the module detects the distance 2 ~ 30cm, detection angle 35 °, the distance can detect potential is adjusted clockwise adjustment potentiometer to detect the distance increases ; counterclockwise to adjust the potentiometer to reduce the detection distance . 2 .active infrared sensors to detect the reflected , and thus the shape of the reflectivity of the target detection range is critical . The minimum detection distance which black , white maximum ; small objects from a small area , a large area from the Grand . 3 . the output port OUT sensor module can be directly connected to the microcontroller IO port , you can directly drive a 5V relay ; Connection : VCC-VCC; GND-GND; OUT-IO 4 .using the comparator LM393, stable ; 5 .can be used for 3-5V DC power supply modules . When the power is turned on, the red power indicator light ; -with the screw holes of 3mm , easy fixed installation ; -board size : 3.1CM * 1.5CM Interface Description (3-wire): -VCC: external 3.3V-5V voltage (can be directly connected to 5v MCU and 3.3v MCU) -GND: GND External -OUT: small board digital output interfaces (0 and 1) Package Include:5 x Infrared obstacle avoidance m

🎉🎉🎉 Welcome to my shop, wish you have a happy day!!! ✔️ We will ship the products within two days. ✔️ If you have any questions, please leave a message, we will reply within 24 hours. ✔️ If you have any questions after receiving the product, please contact us in time. ✔️ If you are satisfied with the product, please give a 5 star rating. Thank you!!! <UAMDear> 5PCS IR Infrared Obstacle Avoidance Sensor Module For Arduino Smart Car Robot Description: -When the module detects an obstacle in front of the signal , the green indicator light on the board level , while low-level continuous output signal OUT port , the module detects the distance 2 ~ 30cm, detection angle 35 °, the distance can detect potential is adjusted clockwise adjustment potentiometer to detect the distance increases ; counterclockwise to adjust the potentiometer to reduce the detection distance . 2 .active infrared sensors to detect the reflected , and thus the shape of the reflectivity of the target detection range is critical . The minimum detection distance which black , white maximum ; small objects from a small area , a large area from the Grand . 3 . the output port OUT sensor module can be directly connected to the microcontroller IO port , you can directly drive a 5V relay ; Connection : VCC-VCC; GND-GND; OUT-IO 4 .using the comparator LM393, stable ; 5 .can be used for 3-5V DC power supply modules . When the power is turned on, the red power indicator light ; -with the screw holes of 3mm , easy fixed installation ; -board size : 3.1CM * 1.5CM Interface Description (3-wire): -VCC: external 3.3V-5V voltage (can be directly connected to 5v MCU and 3.3v MCU) -GND: GND External -OUT: small board digital output interfaces (0 and 1) Package Include: 5 x Infrared obstacle avoidance m

-the sensor module output port OUT can be directly connected to the microcontroller IO port can, also can drive a 5v relay directly; Connection mode: the VCC - VCC; GND - GND; The OUT - the IO -the comparator USES the LM393, working stability -can be used for 3 to 5v dc power to power supply module. When power on, the red power indicator light lit 4. 3 mm screw holes, easy fixed, installation -circuit board size: 3.2CM*1.4CM Module interface specification -VCC voltage is 3.3V to 5V converter (which can be directly connected to 5V single-chip microcontroller and 3.3V) -GND external GND -OUT of small plate digital output interface (0 and 1) Package Included 1 PC IR Infrared Obstacle Avoidance Sensor NOTE:The color difference is hard to avoid in your phone. If you can not accept this little difference, be cautious before you making the orders. thanks for understan

VL53L3CX Time-of-Flight ToF Ranging Sensor ule Breakout 3M 940nm IR Infrared Distance I2C IIC For Arduino functions. The miniature reflowable package integrates a single photon avalanche diode (SPAD) array and physical infrared filter to achieve the best ranging performance under various ambient lighting conditions, and is equipped with various cover glass windows. The VL53L3CX combines the advantages of a high-performance proximity sensor, excellent short-distance linearity, and distance measurement capabilities up to 3 m. VL53L3CX can also detect different objects in the field of view (FoV) through deep understanding. Allows the crosstalk immunity of the cover glass to exceed 80 cm, and has a dynamic smudge compensation function. size:25 x 10.5 x 16mm Material:ABS colour:Black+blue Package Contents: 1 x Ranging Sensor uleOnly the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

The sensor module is perfectly adaptable to the environment light, it has a pair of infrared transmitting and receiving tubes; transmitting tube emits infrared in a certain frequency, when detecting direction meets with obstacles(reflecting surface), reflected infrared will be received by the receiving tube; after the comparator circuit processing, green indicator will light up, at the same time signal output interface to output digital signal(1 low level signal). Users can adjust the detection distance through the potentiometer knob, effective distance range 2~30cm and working voltage is 3.3V to 5V. The module can be widely used in robot obstacle avoidance, obstacle avoidance car, line count, black and white line tracking and so on many occasions. Features: Detection distance is 2~30cm (can be adjusted through the potentiometer); 35° detection angle. Adjust potentiometer clockwise, the detection distance increases; counter-clockwise tuning potentiometer, detection distance is reduced. The output port OUT can be directly connected to the microcontroller IO port, you can directly drive a 5V relay. Connect type: VCC-VCC; GND-GND; OUT-IO. Adopt the comparator LM393 for stable working performance. The working voltage is DC 3.3V to 5V, red power indicator lights up when power on. With the screw holes of 3mm, easy fixed installation. Specifications: Quantity: 5pcs / 20pcs(Optional) Detection Distance: 2~30cm Detection Angle: 35 ° Working Voltage: 3.3V~5V VCC: External 3.3V-5V voltage(can be directly connected to 5V and 3.3V single-chip microcontroller) GND: GND External OUT: Small board digital output interfaces(0 and 1) Connection: VCC-VCC; GND-GND; OUT-IO Board Size: 31 * 14mm / 1.22 * 0.55in Board Weight(1pc): 3g Package Weight: 18-65g Note: Package List: 5 * Infrared Obstacle Avoidance M

The sensor has a pair of infrared / infrared transmitters and receivers. Infrared frequency emitted against the surface of obstacles (Object detected) It will be reflected back and received by the infrared receiver. After being processed by a series of comparisons (Comparator), the green light will light up and emit digital signals (Digital output) Low. The detection distance can be regulated by potentiometers, with effective distances of 2 30cm, working voltage of 3.3v 5v. Easy installled, Easy to use, Many are used in obstacle avoidance robots, Car avoidance, Black and white line trackers and many other uses. How it works: 1. When this module detects impediments in front of the infrared signal, The green indicator lights will be on and the output port releases a low signal continuously. The module can detect a distance of 2 30cm with a detection angle of 35 degrees. Distance Detect Got it Raised With Playback Potentio In the direction Needle Hours And To Reduce Distance Detect Played Opposite Direction Needle The clock. 2. The active infrared sensor detects reflections, hence the reflection form of the object is essential. The black surface has the smallest reflected surface and the white surface has the largest reflection. 3. The output port can be directly connected to io port on the microcontroller. It can also be directly connected to the 5v relay. Connection: Vcc- > vcc, gnd- > gnd, out- > io 4. It uses a stable lm393 comparator comparison. 5. It can be used at 3-5v dc voltage. When turned on, the red indicator lights up. 6. It has a 3mm screw hole for installlation. 7. 3.1cm x 1.5cm module size Interface: 1. Vcc external voltage 3.3v - 5v (connected to 5v and 3.3v mcu) 2. Gnd ground 3. Out digital output interface (0 a

【AIR】5PCS IR Infrared Obstacle Avoidance Sensor Module For Arduino Smart Car RobotDescription: -When the module detects an obstacle in front of the signal , the green indicator light on the board level , while low-level continuous output signal OUT port , the module detects the distance 2 ~ 30cm, detection angle 35 °, the distance can detect potential is adjusted clockwise adjustment potentiometer to detect the distance increases ; counterclockwise to adjust the potentiometer to reduce the detection distance . 2 .active infrared sensors to detect the reflected , and thus the shape of the reflectivity of the target detection range is critical . The minimum detection distance which black , white maximum ; small objects from a small area , a large area from the Grand . 3 . the output port OUT sensor module can be directly connected to the microcontroller IO port , you can directly drive a 5V relay ; Connection : VCC-VCC; GND-GND; OUT-IO 4 .using the comparator LM393, stable ; 5 .can be used for 3-5V DC power supply modules . When the power is turned on, the red power indicator light ; -with the screw holes of 3mm , easy fixed installation ; -board size : 3.1CM * 1.5CM Interface Description (3-wire): -VCC: external 3.3V-5V voltage (can be directly connected to 5v MCU and 3.3v MCU) -GND: GND External -OUT: small board digital output interfaces (0 and 1) Package Include:5 x Infrared obstacle avoidance m

Visit tokoduino dot com Specs: Vcc-vcc; gnd-gnd; out-io - using the comparator lm393, stable - can be used for 3v - 5v dc power supply modules. - detection distance: 2 to 30cm - detection angle: 35 degrees. With the screw holes of 3mm easy fixed installlation - board size: 3.1cm x 1.5cm - adjustable sensitivity using trimpot. - description interface (3-wire): - vcc: External 3.3v-5v voltage (can be directly connected to 5v mcu and 3.3v mcu) - external gnd: - out: Digital output interfaces (0 and 1) - usage: Sample data pulse meter Fax paper shredders detection Obstacle detection. Completeness: 1pcs ir obstacle avoidance sensor module Please wrap gan / sist! There is also a jumper cable to connect this module to arduino / minsys you are only on tokodui

Specs: Output: Low open colctor active. Obstacle led indicator. Power led indicator. Work voltage: 3~5v. Dimension: 32mm x

Specs: - ctrt5000 sensor is highly sensitive and stable. - line sensor for robotics applications - using infrared light. - voltage: 5v. - black line low output, white line high output - distance detection: 10mm - 4.22x0.90x1.25cm Completeness: 1x module sensor follower track

Ultra-thin infrared remote control parameters : 1.CR2025 green button batteries, capacity 160mah 2. Transmission Distance : 8m or more ( specific and the surrounding environment , the receiver sensitivity and other factors ) 3. Effective angle: 60 degrees 4. Sticking material : 0.125mmPET, the useful life of 20,000 times. 5. stable quality, cost-effective 6. quiescent current 3-5uA, dynamic current 3-5mA. Package include

Product Usage: 1. the meter pulse data sampling 2. fax machine shredder paper detection 3. obstacle detection 4. black and white line detection Product description: 1. using TCRT5000 infrared reflection sensor 2. Detection reflection distance: 1mm~25mm 3. working voltage: 5V 4. the output form: digital signal (0 and 1) 5. with fixed bolt holes for easy installation 6. small board PCB size: 3.5cm x 1cm 7. single weight: 4.5g 8. Build-in TCRT5000 Sensor NSOR 9. Applicable to a variety of platforms including for Arduino / AVR / ARM /PIC Features: The infrared emitting diode of the TCRT5000 sensor continuously emits infrared rays. When the emitted infrared rays are not reflected back or reflected back but the intensity is not large enough, the infrared receiving tube is always in the off state, and the output end of the module is low level, indicating The diode is always off; when the detected object appears in the detection range, the infrared light is reflected back and the intensity is large enough, and the infrared receiving tube is saturated. At this time, the output end of the module is high, indicating that the diode is illuminated. Wiring: 1. VCC: Connect the positive pole of the power supply (5V) 2. GND: connected to the negative power supply 3. OUT: high / low level switching signal (digital signal 0 and 1 Package Included: 10PCS*IR Infrared Line Track Follower Sensor TCRT5000 Obstacle Avoidanc For Ar