Oled 0.96 esp8266

Sản phẩm bao gồm 1 bo Mạch thu phát wifi wemos ESP8266 tích hợp sẵn màn hình Oled 0.96 inch. Kit thu phát Wifi ESP8266 NodeMCU Oled 0.96 inch có thể sử dụng trực tiếp trình biên dịch của Arduino để lập trình và nạp code. Các bạn mới bắt đầu làm việc với các ứng dụng IoT rất nên tham khảo module này. Thông số kĩ thuật: - Điện áp cấp cho module: 3.3 – 5VDC - Điện áp giao tiếp: 3.3VDC - Chip nạp và giao tiếp UART: CP2102. - Tích hợp Oled 0.96 inch. - GPIO tương thích hoàn toàn với firmware Node MCU. - Tích hợp Led báo trạng thái, nút Reset, Program. - Tương thích hoàn toàn với trình biên dịch Arduino. TÀI LIỆU: Để sử dụng NodeMCU ESP-12E chúng ta cần cài đặt driver CP2102, Tải tại đây: #LINK https://drive.google.com/file/d/17MgHfsFKBlHqsI8FsztHSxlvxhMx0TrZ/view #nodeMCU #wemos #oled #nodemcuoled #wifi #thuphatwifi

Hello everyone, we are Reland Tech, we are mainly engaged in electronic components, electronic tools, bakery products. Customers can contact us for more product information. If there is any dissatisfaction, you can leave us a comment. We will actively correct, of course, thank you for your sincere evalua

NODEMCU WIFI ESP8266 + NODEMCU 0.96 inch OLED 0.96" We deal in wholesale and retail Feel free to contact us #NODEMCU #WIFI #ESP8266 #OLED #0.96" #0.9

1. Onboard mature and stable ESP-12F WIFI ule, large capacity 4M BYTE FLASH; Onboard l2C communication interface 0.96 inch OLED display; 2. Provide reference codes and documents in OLED display 51, STM32 and other environments; The onboard PCF8563T clock circuit can operate normally even if the power is off; 3. Extend the ESP8266UART interface to support secondary development and burn your own firmware; Provide ESP8266 factory firmware, schematic diagram; 4. Power supply e: Mini USB5V power supply; Double-layer structure design, small size and better appearance, it is the best choice for DIYWIFI clock. 1.0.96 inch OLED screen: the driver IC is SSD1306; 2. ESP-12F WIFI ule: the flash memory capacity is 4MBYTE; 3. Mini USB 5V power interface; 4. PCF8563T clock chip; 5. CR1220 button battery: power supply for the clock circuit after power off 6. UART program download interface: short-circuit IO0 and GND when downloading, connect 3V3, TXD, RXD, and GND to 3V3, RXD, TXD, GND of the external TTL serial port ule (called FT232 ule), and insert the download I00 and GND link after completion; 7.0 LED interface: SDA, SCL, GND, 3V3; OLED self-luminous, no backlight Voltage: 3.3V-5V DC Viewing angle: 160 degrees or more Working temperature: -30 degrees Celsius to 70 degrees Celsius I2C interface: GND: Ground wire VCC: 3.3V-5V SCL: I2C serial clock (UNO: A5; MEGA: 21) SDA: I2C serial data (UNO: A4; MEGA: 20) size:29 x 29mm Material:PCB colour:Blue+black Package Contents: 1 x 0.96 Inch OLED Display uleOnly the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

1. Onboard mature and stable ESP-12F WIFI ule, large capacity 4M BYTE FLASH; Onboard l2C communication interface 0.96 inch OLED display; 2. Provide reference codes and documents in OLED display 51, STM32 and other environments; The onboard PCF8563T clock circuit can operate normally even if the power is off; 3. Extend the ESP8266UART interface to support secondary development and burn your own firmware; Provide ESP8266 factory firmware, schematic diagram; 4. Power supply e: Mini USB5V power supply; Double-layer structure design, small size and better appearance, it is the best choice for DIYWIFI clock. 1.0.96 inch OLED screen: the driver IC is SSD1306; 2. ESP-12F WIFI ule: the flash memory capacity is 4MBYTE; 3. Mini USB 5V power interface; 4. PCF8563T clock chip; 5. CR1220 button battery: power supply for the clock circuit after power off 6. UART program download interface: short-circuit IO0 and GND when downloading, connect 3V3, TXD, RXD, and GND to 3V3, RXD, TXD, GND of the external TTL serial port ule (called FT232 ule), and insert the download I00 and GND link after completion; 7.0 LED interface: SDA, SCL, GND, 3V3; OLED self-luminous, no backlight Voltage: 3.3V-5V DC Viewing angle: 160 degrees or more Working temperature: -30 degrees Celsius to 70 degrees Celsius I2C interface: GND: Ground wire VCC: 3.3V-5V SCL: I2C serial clock (UNO: A5; MEGA: 21) SDA: I2C serial data (UNO: A4; MEGA: 20) size:29 x 29mm Material:PCB colour:Blue+black Package Contents: 1 x 0.96 Inch OLED Display uleOnly the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

ESP8266 Weather Station Kit with DHT11 Temperature Humidity/BMP180 Atmospheric Pressure/BH1750FVI Light Sensor 0.96 Inches OLED Display Module Replacement for Arduino for IDE IoT Starter,The weather station uses the ESP8266-12E to obtain data from the Internet: time of a city, weather and forecast information of next 3 days, makes these data scroll on the SSD1306 OLED display. You can switch to display data from any city in the world. Also the device uses sensors of DHT11, BMP180, BH1750FVI to collect data, like temperature, humidity, atmospheric pressure, etc. These data will be read by the weather station via sensor every 5 seconds and uploaded to the Internet per 60 seconds, which enables you to grasp real-time data charts by your phone or computer. And it is available to modify the code to achieve different functions. Features: ESP8266: ESP8266-12E module Features with built-in CP2102 chip, micro USB, 4MB flash memory, complete I/O port and wireless 802.11 supported IOT platform, module replacement for Arduino. DHT11: This sensor is a calibrated temperature and humidity sensor with digital signal output. Simple communication protocol simplifies programming job, greatly reduces the programming effort required. BMP180: It is a high-precision, small-sized, super-low power sensor that has excellent performance, power consumption as low as 3μA, minimum absolute accuracy reaching 0.03 hPa, and pressure range of 300~1100hPa. BH1750FVI: BH1750FVI digital light intensity sensor adopts direct digital output, requires no complex calculation, omits calibration. LCD Display: 0.96-in SSD1306 yellow and blue OLED LCD display with I2C IIC SPI serial, has high resolution (128*64), provides clear viewing. Specifications: Material: Electronic Components Package Weight: 170g / 5.99oz Package Size: 14.5*8.8*4cm / 5.70*3.46*1.57in Note: Weather station kit only, other accessories in the picture are not included. Due to manual measurement, there may be deviation. Due to lighting, the picture and material object may slightly differ in color, please in kind prevail. Packing List: 1 * ESP8266-12E 1 * DHT11 1 * BMP180 1 * BH1750FVI 1 * OLED Display 1 * USB Cable 2 * Breadboard 20 * Dupont

NODEMCU WIFI and ESP8266 NODEMCU 0.96 inch OLED Note: Due to manual measurement, please allow 1-3mm different. Due to different displays and different lighting, the image may not reflect the actual colors of the project. Thank you for your understanding. When purchasing electronic components, please have certain electronic basic knowledge of the module. Most modules only provide descriptions or send materials. There is no technical consulting support. Please be careful to shoot for begin

new NODEMCU wifi ESP8266 ESP-12F wemos for ESP12F 0.96 INCH OLED Description: This is a low cost ESP8266 WIFI development board for Arduino. 0.96" OLED display on the board, easy for beginners, can be programmed for Arduino, project support the ESP8266 chip for Arduino environment, for Arduino core ESP8266 WiFi chip, another famous project is NodeMCU. The NodeMCU can be used to control ESP8266. Feature: All ESP8266 pin decomposition 12 digital pin write/read/interrupt/pwm / I2C / single line support (except D0) 1 analog input 0.96" OLED Micro USB Interface Compatible for Arduino, NodeMCU, WeMos Input power supply 4.75V~12V Size: 6.2x2.7cm / 2.44x1.06inch Note: Due to manual measurement, please allow an error of 1-2cm. Please make sure you don't mind before bidding. Due to the differences between the different displays, the image may not reflect the actual color of the project. Thank

Màn hình android oled c1 cho ô tô xe hơi Bảo hành chính hãng oled 12 tháng lỗi đổi mới Giá trên đã bao gồm mặt dưỡng và camera lùi ahd cho tất cả các xe ô tô Màn hình ô tô thông minh là một trong những thiết bị ô tô hiện đại, được áp dụng công nghệ tiến tiến giúp cho chiếc xe của bạn thêm tiện nghi, sang trọng, nâng cao độ an toàn khi lái xe nhờ những tiện ích rảnh tay và khả năng bao quát cũng như hệ thống cảnh báo mà chiếc màn hình xe hơi này đem lại. Mô tả chi tiết sản phẩm Màn hình android oled c1 cho ô tô xe hơi Bộ nhớ: Ram 2GB + 32GB Rom CPu 4 Core Độ phân giải: Full Hd (1024 x 600 pixels) Màn hình rộng: 9 inch hoặc 10 inch Hệ điều hành android (Pie) Chip set: A7 core 1.3 Ghz x 4 Công nghệ màn hình: Oled ips Kính cường lực: 2,5D Hỗ trợ : 4G LTE Cổng kết nối: USB x 2 Tích hợp Oled Ai - Ra Lệnh Giọng Nói thông minh nhất hiện tại có bản đồ dẫn đường navitel trọn đời giới hạn tốc độ khi đi trên đường sử dụng vệ tinh không cần 4G Đầy đủ chức năng : Youtube, Navitel, Google Maps, Mp3, Mp4, Video ... Bảo hành chính hãng Oled 12 Tháng Lỗi đổi mới Đóng gói sản phẩm bao gồm: 1 x Màn hình android oled c1 cho ô tô xe hơi 9 inch hoặc 10 inch theo mặt dưỡng zin của xe 1 x Mặt dưỡng kèm dây nguồn zin theo xe ô tô kèm dây jack zin 1 x canbus nếu có 1 x Bộ dây jack đầy đủ theo Màn hình 1 x Camera lùi ahd Shop có hỗ trợ lắp đặt tại: Cổng chung cư 789 Xuân Đỉnh - Ngoại Giao Đoàn ( Cuối đường Nguyễn Văn Huyên kéo dài) hotline 0915191869/ 0354865869 Giá trên chưa bao gồm công lắp đặt Với Quý khách ở xa được hỗ trợ kỹ thuật qua video call hỗ trợ lắp đặt tại nhà #man #hinh #android #oled #c1 #c2 #9inch #10inch #o #to #xe #hoi

Welcome:) Please read it carefully! "All things ready stock" Specs and dimensions look at the picture For the size and color it can be written down. Buy = agree (no comp

E/placement maleen martyrs with 0.96 oled expanded temperature and humidity development board. Designing male and female stakes in open source items, a discharge system of 18650 was set up on the development panel， self charged discharge protection， meanwhile, a oled and five-way key is set up to facilitate development. This is the same as the mishap and the madness.， added a programmable berry, you can use gp16 to control it， displays the functionality of 8266. Collected oled and five way keys， development easier Press the five way button from the merry one, return, d5, d6, d7 Control The maddened s got the d1 feet and the d2 feet, respectively The 5 digital pins can be equipped separately with mishap/ice makers/merry mileage/pwm/xygen/iconic icebergs ice cream. 1 ad input Put together the Pleasant Charge Discharge System 18650 Micro sterile import Grazing mishap Pleasant and compatible Wide voltage input range 5v~12v 1 male sterile can control the availability of electricity 1 programmable (D0) Protection Discharge protection Please don't burn the millet in the process， when you burn the martyrs, please pull down the masters and confirm where they are on. Notes： This product does not contain any males， you can't reverse the panicle when installing， otherwise, the burn will destroy the chip It is recommended to use a 5v500 mishap for the male star.， there will be fever above 5v1a， does not affect normal work， but do not touch the chips or gobble up the millet in the process， when measured, the madam chip and diode will rise to about 60 degrees， don't get hot when you work normally， rest ass

Housespace ESP8266 Weather Station Kit with DHT11 Temperature Humidity/BMP180 Atmospheric Pressure/BH1750FVI Light Sensor 0.96 Inches OLED Display Module Replacement for Arduino for IDE IoT Starter The weather station uses the ESP8266-12E to obtain data from the Internet: time of a city, weather and forecast information of next 3 days, makes these data scroll on the SSD1306 OLED display. You can switch to display data from any city in the world. Also the device uses sensors of DHT11, BMP180, BH1750FVI to collect data, like temperature, humidity, atmospheric pressure, etc. These data will be read by the weather station via sensor every 5 seconds and uploaded to the Internet per 60 seconds, which enables you to grasp real-time data charts by your phone or computer. And it is available to modify the code to achieve different functions. Features: ESP8266: ESP8266-12E module Features with built-in CP2102 chip, micro USB, 4MB flash memory, complete I/O port and wireless 802.11 supported IOT platform, module replacement for Arduino. DHT11: This sensor is a calibrated temperature and humidity sensor with digital signal output. Simple communication protocol simplifies programming job, greatly reduces the programming effort required. BMP180: It is a high-precision, small-sized, super-low power sensor that has excellent performance, power consumption as low as 3μA, minimum absolute accuracy reaching 0.03 hPa, and pressure range of 300~1100hPa. BH1750FVI: BH1750FVI digital light intensity sensor adopts direct digital output, requires no complex calculation, omits calibration. LCD Display: 0.96-in SSD1306 yellow and blue OLED LCD display with I2C IIC SPI serial, has high resolution (128*64), provides clear viewing. Specifications: Material: Electronic Components Package Weight: 170g / 5.99oz Package Size: 14.5*8.8*4cm / 5.70*3.46*1.57in Note: Weather station kit only, other accessories in the picture are not included. Due to manual measurement, there may be deviation. Due to lighting, the picture and material object may slightly differ in color, please in kind prevail. Packing List: 1 * ESP8266-12E 1 * DHT11 1 * BMP180 1 * BH1750FVI 1 * OLED Display 1 * USB Cable 2 * Breadboard 20 * Dupont

Hello everyone, our company is in Shenzhen。we specialize in selling module. When we receive your order, we will process your order within 24 hours. If you order many items, we may need more time to process, it will not be more than 5 days, please be patient. Genaral it need 1-2weeks arrive your hand.if you chat with us , we donot reply you, donot worry , we are try to handle your order.so pls donot cancel o

ESP8266 NODEMCU with 0.96 OLED extended temperature and humidity development board meteorological station wIFI The design concept is derived from the open source project NodeMCU. The development board integrates an 18650 charge and discharge system with its own charge and discharge protection. It also integrates an OLED and five-way button for easy development.         The operation of this treasure is the same as that of NodeMCU, adding a programmable LED, which can be controlled by GPIO16, displaying the running status of 8266 and other functions. Integrated OLED and five-way button, more convenient for development Five-way keys are controlled by FLATH, RSET, D5, D6, D7 SDA and SCL of OLED are connected to D1 and D2 respectively 5 digital pins can be configured with write / read / interrupt / pwm / I2C / one-wire supported 1 AD input Integrated 18650 battery charging and discharging system Micro USB input Arduino compatible NodeMCU compatible Wide voltage input range 5V ~ 12V 1 switch can control whether 18650 power supply 1 programmable LED (D0) Charge protection Discharge protection  Please do not burn the program during the charging process. When you burn the program, please remove the battery and confirm that the switch is in the ON position Note: This product does not contain 18650 battery, you can not reverse the connection when installing the battery, otherwise it will burn the charging chip!  It is recommended to use a 5V500MA charger for charging. There will be heat generation above 5V1A, which will not affect the normal work. It does not get hot when you carry it. Note: Due to manual measurement, please allow 1-3mm different. Due to different displays and different lighting, the image may not reflect the actual colors of the project. Thank you for your understanding. When purchasing electronic components, please have certain electronic basic knowledge of the module. Most modules only provide descriptions or send materials. There is no technical consulting support. Please be careful to shoot for begin

As we are dealing with a wide variety of electronic components, we cannot upload them all. if you can't find the models you need in our store, please contact us. we will quote you first time and contact the store for a large number of diskounts. Module esp8266 12f wifi & 1.3 inch 0.96 inch oled+bottom extension board m

1. Thông tin về sản phẩm : Module NODEMCU WIFI ESP8266 OLED NODEMCU 0.96 inch Module NODEMCU WIFI ESP8266 OLED NODEMCU 0.96 inch là sự kết hợp giữa Module RF thu phát Wifi ESP8266 NodeMCU và Oled 0.96 inch, có thiết kế nhỏ gọn, màn hình Oled hiển thị chuyên nghiệp và thiết kế tối ưu cho độ bền, độ ổn định cao. Với module NODEMCU WIFI ESP8266, bạn có thể sử dụng trực tiếp trình biên dochj của Arduino để lập trình và nạp code. Các bạn mới bắt đầu làm việc với các ứng dụng IoT nên tham khảo module này. NodeMCU ESP8266 Oled 0.96inch WeMos có thể dùng như một trạm thu thập duex liệu từ xa và gửi lên máy chủ, sau đó người sử dụng có thể lấy và xử lí dữ liệu đó. Thông Số Kĩ Thuật: Điện áp cấp cho module: 3.3 – 5VDC Điện áp giao tiếp: 3.3VDC Chip nạp và giao tiếp UART: CP2102. Tích hợp Oled 0.96inch Driver SSD1306 giao tiếp I2C. GPIO tương thích hoàn toàn với firmware Node MCU. Tích hợp Led báo trạng thái, nút Reset, Program. Tương thích hoàn toàn với trình biên dịch Arduino. Kích thước Module Nodemcu Wifi ESP8266: 6x2.7 cm Trọng lượng: 20g 2. Vì sao khách hàng yên tâm khi mua hàng tại Linh Kiện Điện Tử 3M - Giá sản phẩm luôn tốt hơn so với thị trường. - Cam kết sản phẩm giống y hình. - Tư vấn miễn phí 24/7 trước và sau khi đặt hàng. ------------------------------------------------------------------ LH Hotline: 024 2021

✨Thank you for visiting our shop! 👉China's most professional electric equipment wholesale manufacturer, follow us to get more s and information! Give us ⭐⭐⭐⭐⭐ good reviews and get exclusive s! The weather station uses the ESP8266-12E to obtain data from the Internet: time of a city, weather and forecast information of next 3 days, makes these data scroll on the SSD1306 OLED display. You can switch to display data from any city in the world. Also the device uses sensors of DHT11, BMP180, BH1750FVI to collect data, like temperature, humidity, atmospheric pressure, etc. These data will be read by the weather station via sensor every 5 seconds and uploaded to the Internet per 60 seconds, which enables you to grasp real-time data charts by your phone or computer. And it is available to modify the code to achieve different functions. Features: ESP8266: ESP8266-12E module Features with built-in CP2102 chip, micro USB, 4MB flash memory, complete I/O port and wireless 802.11 supported IOT platform, module replacement for Arduino. DHT11: This sensor is a calibrated temperature and humidity sensor with digital signal output. Simple communication protocol simplifies programming job, greatly reduces the programming effort required. BMP180: It is a high-precision, small-sized, super-low power sensor that has excellent performance, power consumption as low as 3μA, minimum absolute accuracy reaching 0.03 hPa, and pressure range of 300~1100hPa. BH1750FVI: BH1750FVI digital light intensity sensor adopts direct digital output, requires no complex calculation, omits calibration. LCD Display: 0.96-in SSD1306 yellow and blue OLED LCD display with I2C IIC SPI serial, has high resolution (128*64), provides clear viewing. Specifications: Material: Electronic Components Package Weight: 170g / 5.99oz Package Size: 14.5*8.8*4cm / 5.70*3.46*1.57in Note: Weather station kit only, other accessories in the picture are not included. Due to manual measurement, there may be deviation. Due to lighting, the picture and material object may slightly differ in color, please in kind prevail. Packing List: 1 * ESP8266-12E 1 * DHT11 1 * BMP180 1 * BH1750FVI 1 * OLED Display 1 * USB Cable 2 * Breadboard 20 * Dupont

WIFI Kit series is the new development of the cost-effective networking program, the main chip using Lexin ESP32, Tensilica LX6 dual-core processor, clocked at 240MHz, computing power up to 600DMIPS, chip built-in 520 KB SRAM, 802.11 b / g / N HT40 Wi-Fi transceiver, baseband, protocol stack and LWIP, integrated dual-mode Bluetooth (traditional Bluetooth and BLE low power Bluetooth). This product is based on the WIFI Kit 32 added SX1278 chip, that is,for LoRa remote modem, 433MHz frequency, about -148dBm high sensitivity, +20 dBm power output, high reliability, transmission distance (measured open area communication distance 2.6Km). Onboard 32MByte Flash, Wi-Fi antenna, 0.96-inch blue OLED display, lithium battery charging circuit and interface, CP2102 USB to serial chip, the perfect support for Arduino development environment, can be very simple and fast for program verification and product development. Note: This item come unassembled, soldering is required, not equipped with lithium battery. Here is the link with English documentation: https://hackaday.io/project/26991-esp32-board-wifi-lora-32 https://robotzero.one/heltec-wifi-kit-32/; Operating voltage: 3.3V to 7V Operating temperature range: -40 ° C to + 90 ° C Supports Sniffer, Station, softAP and Wi-Fi Direct modes Data rate: 150 Mbps @ 11n HT40,72 Mbps @ 11n HT20,54 Mbps @ 11g, 11 Mbps @ 11b Transmit power: 19.5 dBm @ 11b, 16.5 dBm @ 11g, 15.5 dBm @ 11n Receiver sensitivity up to - 98 dBm UDP continues to throughput by 135 Mbps Package included: 1* ESP32 0.96" OLED WiFi Bluetooth Development

Description: The weather station uses the ESP8266-12E to obtain data from the Internet: time of a city, weather data and forecast information for the next 3 days, scrolling on the SSD1306 OLED Display; The device can switch to display data from any city in the world - maybe your relatives or friends live there. The device uses sensors DHT11, BMP180, BH1750FVI to collect temperature, humidity, Atmosphetic Pressure and light data. The weather station reads data indoor via sensor every 5 seconds and uploads it to the Internet every 60 seconds. You can see real-time data charts from your phone or computer.Of course you can modify the code to implement different functions. Features: ESP8266: CP2102 chip inside, Micro USB, 4MB flash, full I/O port and wireless 802.11 supported IOT platform for Arduino compatible. DHT11 Sensor: A digital signal output with a calibrated temperature and humidity combined sensor. The simple communication protocol greatly reduces the programming effort required. BMP180: high-precision, small size, ultra-low power 3μA pressure sensor. Its performance excellence, the absolute accuracy of the lowest can reach 0.03hPa. Can directly through the I2C bus connected with a variety of microprocessors. Pressure range: 300 ~ 1100hPa. BH1750FVI: Digital Light intensity Sensor. Direct digital output, complex calculation is omitted, omitting calibration. OLED Yellow Blue Display: 0.96" SSD1306 128X64 Yellow&Blue OLED LCD Display with I2C IIC SPI Serial only Windows OS. Result: -Get weather data from OpenWeathermap at regular intervals, showing the weather of today and weather forecast for next 3 days in any city in the world. -Read the current temperature, humidity data indoor at regular intervals. -Regular reading of atmospheric pressure, light intensity data. Guidance Manual Catalog: Overview: This manual describes how to make a miniature weather station by Arduino IDE Step 1: Install USB-To-Serial Step 2: Install for Arduino IDE for ESP8266 Step 3: Burning Firmware to ESP8266 Step 4: Connecting Components Step 5: Register OpenWeathermap, thingspeak new account Step 6: Import WeatherStation code in the for Arduino IDE Step 7: Add Library Step 8: Modify File WeatherStation.ino Step 9: Set the Board and Port again Step 10: Burn code to ESP8266 Step 11: Result AT-Firmware in Guidance Document: Ai-Thinker_ESP8266_DOUT_8Mbit_v1.5.4.1-a_20171130.bin Library attachment in Guidance Document: esp8266-weather-station-master.zip esp8266-oled-ssd1306-master.zip json-streaming-parser-master.zip Tools in Guidance Document: ESP8266Flasher.exe usb-to-serial.rar Package includes: 1* ESP8266-12E 1* DHT11 1* BMP180 1* BH1750FVI 1* OLED Display 1* USB cable 2* Breadboard 20* For Dupont

Can be the lowest price of the supplier, the spot is hot.~~~ We are shipping overseas The price in the store is the lowest price. Since we are an overseas direct sales store, the goods will arrive longer. Point, usually 8 to 12 days after the order is delivered, such as urgent users, please be careful! ! ! Those who cancel the order and do not pick up the goods will be held accountable for their personal responsibility! ! ! Important Tips→If you are charged [tariff] [tariff] [tariff], contact our customer service to let us compensate some of the tax, remember to remember Shopping Tips: So the style and size are available, but due to inventory changes It is best to consult us or talk about it, or you can note the color size of the style you need when you subscript. We are easy to arrange shipping within 3-5 working days! Please be sure to subscript, thank you! ! ! The store will only be replaced, except for major defects, the exchange will be paid as a shipping subsidy to the manufacturer, thank you

Features: One AD inputs. Micro USB inputs. One programmable LED (D0). Integrated 18650 battery charging and discharging system. One switch controls whether the 18650 battery is powered or not. OLED's SDA and SCL connect to the D1 pin and the D2 pin respectively. The five buttons are controlled by FLATH, RSET, D5, D6, and D7 respectively. The 5 Digital pins can configure the write/read/interrupt/pwm/I2C/one-wire supported separately. Operation and NodeMCU consistent, adding a programmable LED, you can use GPIO16 to control, display 8266 running status and other functions. Integrated OLED and five button, more convenient for development. The design concept originates from the open source project NodeMCU, and the development board integrates 18650 charging and discharging systems with charging and discharging protection. At the same time, a OLED and five directional buttons are integrated to facilitate the development. Specifications: Model: ESP-8266 Color: Black Charging Protection: Yes Discharge Protection: Yes Compatible With Arduino Compatible With NodeMCU Wide Voltage Input Range: 5V~12V Charge Current: 500 mA Size:10.3x3cm/4.06x1.18" Display Size: 0.96 Inch Quantity: 1 Pc Note: Please allow 1-3mm error due to manual measurement. pls make sure you do not mind before you bid Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you! No Retail Package Package Includes: 1 x ESP8266 Mini-WiFi NodeMCU Module With 10

Our products only provide product information or details, without technical support, buyers need to understand, thank you for your cooperation The design concept is derived from open source project nodemcu, which integrates 18650 charging and diskharging system, self-charging and diskharging protection, and an oled and five-directional keystroke for easy development. This baby operation is consistent with nodemcu, adding a programmable led that can be controlled by gpio 16, displaying the 8266 running state and so on.Integrated oled and five-way keys to make it easier to develop The five-way keys are controlled by flath, rset, d5, d6, d7, respectively Oled's s sda and scl received d1 and d2 feet, respectively 5 digit pins can be configured with write/read/interim/pwm/i2c/one-wire supported 1 ad input Integrated 18650 battery charging and diskharge system Micro usb input Arduino compatible Nodemcu compatible Wide voltage input range 5v~12v 1 switch to control 18650 power supply 1 programmable led (d0) Charging protection Diskharge protection Please don't record the program while charging. when you record the program, unplug the battery and make sure the switch is on Note: this product does not contain 18650 batteries. the battery can not be installled back-to-back, otherwise the charging chip will burn down Charging recommendation 5v500ma charger for charging,Fever at or above 5v1a,Not affecting normal work,But don't touch the charging chip or carry it with you during charging,Charging chips and diodes rise to about 60 degrees when measured,No fever at normal work,Don't worry about carryin

Module NODEMCU WIFI ESP8266 OLED NODEMCU 0.96 inch Module NODEMCU WIFI ESP8266 OLED NODEMCU 0.96 inch là sự kết hợp giữa Module RF thu phát Wifi ESP8266 NodeMCU và Oled 0.96 inch, có thiết kế nhỏ gọn, màn hình Oled hiển thị chuyên nghiệp và thiết kế tối ưu cho độ bền, độ ổn định cao. Với module NODEMCU WIFI ESP8266, bạn có thể sử dụng trực tiếp trình biên dochj của Arduino để lập trình và nạp code. Các bạn mới bắt đầu làm việc với các ứng dụng IoT nên tham khảo module này. NodeMCU ESP8266 Oled 0.96inch WeMos có thể dùng như một trạm thu thập duex liệu từ xa và gửi lên máy chủ, sau đó người sử dụng có thể lấy và xử lí dữ liệu đó. Thông Số Kĩ Thuật: Điện áp cấp cho module: 3.3 – 5VDC Điện áp giao tiếp: 3.3VDC Chip nạp và giao tiếp UART: CP2102. Tích hợp Oled 0.96inch Driver SSD1306 giao tiếp I2C. GPIO tương thích hoàn toàn với firmware Node MCU. Tích hợp Led báo trạng thái, nút Reset, Program. Tương thích hoàn toàn với trình biên dịch Arduino. Kích thước Module Nodemcu Wifi ESP8266: 6x2.7 cm Trọng lượng: 20g ============ THỜI GIAN VẬN CHUYỂN ✯ Sau khi đặt hàng 12 – 24h, Shop sẽ giao cho bên vận chuyển. ✯ Hà Nội, Các Thành Phố Lớn vận chuyển thêm khoảng 1 – 2 Ngày. ✯ Các Tỉnh Thành, Huyện, Xã, Ấp vận chuyển thêm khoảng 2 – 4 Ngày. ✯ Trong thời gian này các bạn giữ máy điện thoại để bưu tá liên lạc giao hàng nhé. Nếu có số gọi nhỡ các bạn gọi lại cho họ nhé ============ THÔNG TIN THÊM VỀ SHOP 🔸 Shop cung cấp bán buôn bán lẻ toàn quốc 🔸 Giá bán cạnh tranh. 🔸 Các Bạn Có Nhu Cầu Nhập Sỉ Số Lượng Lớn Hãy Chat Với Gian Hàng Nhé 🔸 Ngoài các sản phẩm shop có, các bạn có thể tư vấn sản phẩm để đợt nhập mới shop nhập về bán bổ sung sản phẩm. #Module-NODEMCU #WIFI #ESP8266 #OLED #NODEMCU #0.96 inch #linhkiendientu #linhkien #linhkien024 #linhkienlammach #lammachthucong Hotline: 09786

ESP8266 Weather Station Kit with DHT11 Temperature Humidity/BMP180 Atmospheric Pressure/BH1750FVI Light Sensor 0.96 Inches OLED Display Module Replacement for Arduino for IDE IoT Starter,The weather station uses the ESP8266-12E to obtain data from the Internet: time of a city, weather and forecast information of next 3 days, makes these data scroll on the SSD1306 OLED display. You can switch to display data from any city in the world. Also the device uses sensors of DHT11, BMP180, BH1750FVI to collect data, like temperature, humidity, atmospheric pressure, etc. These data will be read by the weather station via sensor every 5 seconds and uploaded to the Internet per 60 seconds, which enables you to grasp real-time data charts by your phone or computer. And it is available to modify the code to achieve different functions. Features: ESP8266: ESP8266-12E module Features with built-in CP2102 chip, micro USB, 4MB flash memory, complete I/O port and wireless 802.11 supported IOT platform, module replacement for Arduino. DHT11: This sensor is a calibrated temperature and humidity sensor with digital signal output. Simple communication protocol simplifies programming job, greatly reduces the programming effort required. BMP180: It is a high-precision, small-sized, super-low power sensor that has excellent performance, power consumption as low as 3μA, minimum absolute accuracy reaching 0.03 hPa, and pressure range of 300~1100hPa. BH1750FVI: BH1750FVI digital light intensity sensor adopts direct digital output, requires no complex calculation, omits calibration. LCD Display: 0.96-in SSD1306 yellow and blue OLED LCD display with I2C IIC SPI serial, has high resolution (128*64), provides clear viewing. Specifications: Material: Electronic Components Package Weight: 170g / 5.99oz Package Size: 14.5*8.8*4cm / 5.70*3.46*1.57in Note: Weather station kit only, other accessories in the picture are not included. Due to manual measurement, there may be deviation. Due to lighting, the picture and material object may slightly differ in color, please in kind prevail. Packing List: 1 * ESP8266-12E 1 * DHT11 1 * BMP180 1 * BH1750FVI 1 * OLED Display 1 * USB Cable 2 * Breadboard 20 * Dupont

1. Onboard mature and stable ESP-12F WIFI ule, large capacity 4M BYTE FLASH; Onboard l2C communication interface 0.96 inch OLED display; 2. Provide reference codes and documents in OLED display 51, STM32 and other environments; The onboard PCF8563T clock circuit can operate normally even if the power is off; 3. Extend the ESP8266UART interface to support secondary development and burn your own firmware; Provide ESP8266 factory firmware, schematic diagram; 4. Power supply e: Mini USB5V power supply; Double-layer structure design, small size and better appearance, it is the best choice for DIYWIFI clock. 1.0.96 inch OLED screen: the driver IC is SSD1306; 2. ESP-12F WIFI ule: the flash memory capacity is 4MBYTE; 3. Mini USB 5V power interface; 4. PCF8563T clock chip; 5. CR1220 button battery: power supply for the clock circuit after power off 6. UART program download interface: short-circuit IO0 and GND when downloading, connect 3V3, TXD, RXD, and GND to 3V3, RXD, TXD, GND of the external TTL serial port ule (called FT232 ule), and insert the download I00 and GND link after completion; 7.0 LED interface: SDA, SCL, GND, 3V3; OLED self-luminous, no backlight Voltage: 3.3V-5V DC Viewing angle: 160 degrees or more Working temperature: -30 degrees Celsius to 70 degrees Celsius I2C interface: GND: Ground wire VCC: 3.3V-5V SCL: I2C serial clock (UNO: A5; MEGA: 21) SDA: I2C serial data (UNO: A4; MEGA: 20) size:29 x 29mm Material:PCB colour:Blue+black Package Contents: 1 x 0.96 Inch OLED Display uleOnly the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

The weather station uses the ESP8266-12E to obtain data from the Internet: time of a city, weather and forecast information of next 3 days, makes these data scroll on the SSD1306 OLED display. You can switch to display data from any city in the world. Also the device uses sensors of DHT11, BMP180, BH1750FVI to collect data, like temperature, humidity, atmospheric pressure, etc. These data will be read by the weather station via sensor every 5 seconds and uploaded to the Internet per 60 seconds, which enables you to grasp real-time data charts by your phone or computer. And it is available to modify the code to achieve different functions. Features: ESP8266: ESP8266-12E module Features with built-in CP2102 chip, micro USB, 4MB flash memory, complete I/O port and wireless 802.11 supported IOT platform, module replacement for Arduino. DHT11: This sensor is a calibrated temperature and humidity sensor with digital signal output. Simple communication protocol simplifies programming job, greatly reduces the programming effort required. BMP180: It is a high-precision, small-sized, super-low power sensor that has excellent performance, power consumption as low as 3μA, minimum absolute accuracy reaching 0.03 hPa, and pressure range of 300~1100hPa. BH1750FVI: BH1750FVI digital light intensity sensor adopts direct digital output, requires no complex calculation, omits calibration. LCD Display: 0.96-in SSD1306 yellow and blue OLED LCD display with I2C IIC SPI serial, has high resolution (128*64), provides clear viewing. Specifications: Material: Electronic Components Package Weight: 170g / 5.99oz Package Size: 14.5*8.8*4cm / 5.70*3.46*1.57in Note: Weather station kit only, other accessories in the picture are not included. Due to manual measurement, there may be deviation. Due to lighting, the picture and material object may slightly differ in color, please in kind prevail. Packing List: 1 * ESP8266-12E 1 * DHT11 1 * BMP180 1 * BH1750FVI 1 * OLED Display 1 * USB Cable 2 * Breadboard 20 * Dupont

Before order asks stock first via diskussion or stock check on the official jogjarobotika web (open jogjarobotika com search product name) Our store has experienced since 2011 in online / offline retail sales. Shipment of your components is secure with packing dus and bubble pack. +==================================================================+ Detail: Check the picture The price is for 1pcs +==================================================================+ Wemos nodemcu wifi for arduino and nodemcu esp8266 + 0.96 inch oled board All esp8266 pins broken out. 12 digital pins 1 analog input Integrated 0.96 ''" oled Micro usb connection Compatible with arduino Compatible with nodemcu (lua for esp8266) Input power 5v Compatible for arduino Compatible with nodemcu (lua for esp8266) Click the link for more details: https://github.com/squix78/esp8266-oled-ss

Module NODEMCU WIFI ESP8266 OLED NODEMCU 0.96 inch Module NODEMCU WIFI ESP8266 OLED NODEMCU 0.96 inch là sự kết hợp giữa Module RF thu phát Wifi ESP8266 NodeMCU và Oled 0.96 inch, có thiết kế nhỏ gọn, màn hình Oled hiển thị chuyên nghiệp và thiết kế tối ưu cho độ bền, độ ổn định cao. Với module NODEMCU WIFI ESP8266, bạn có thể sử dụng trực tiếp trình biên dochj của Arduino để lập trình và nạp code. Các bạn mới bắt đầu làm việc với các ứng dụng IoT nên tham khảo module này. NodeMCU ESP8266 Oled 0.96inch WeMos có thể dùng như một trạm thu thập duex liệu từ xa và gửi lên máy chủ, sau đó người sử dụng có thể lấy và xử lí dữ liệu đó. Thông Số Kĩ Thuật: Điện áp cấp cho module: 3.3 – 5VDC Điện áp giao tiếp: 3.3VDC Chip nạp và giao tiếp UART: CP2102. Tích hợp Oled 0.96inch Driver SSD1306 giao tiếp I2C. GPIO tương thích hoàn toàn với firmware Node MCU. Tích hợp Led báo trạng thái, nút Reset, Program. Tương thích hoàn toàn với trình biên dịch Arduino. Kích thước Module Nodemcu Wifi ESP8266: 6x2.7 cm Trọng lượng: 20g ----------------------- HOTLINE: 024.2021.4848 ZALO : 0987.988.041 Địa chỉ mua hàng tại Hà Nội: 28- Ngõ 106- Lê Thanh Nghị- Hai Bà Trưng- Hà Nội ----------------------- Linh Kiện Điện Tử 3M cam kết: Bán giá luôn cạnh tranh và dịch vụ sau mua giá tốt hơn so với thị trường. Cam kết hoàn tiền 100% khi sản phẩm sai quảng cáo,hoặc lỗi do nhà sản xuất. Cam kết Sản Phẩm giống ảnh Bảo hành đổi trả sản phẩm trong vòng 7 ngày Bảo hành sản phẩm trong vòng 7 tháng bằng hoá đơn mua hàng đi

ESP8266 Weather Station Kit with DHT11 Temperature Humidity/BMP180 Atmospheric Pressure/BH1750FVI Light Sensor 0.96 Inches OLED Display Module Replacement for Arduino for IDE IoT Starter,The weather station uses the ESP8266-12E to obtain data from the Internet: time of a city, weather and forecast information of next 3 days, makes these data scroll on the SSD1306 OLED display. You can switch to display data from any city in the world. Also the device uses sensors of DHT11, BMP180, BH1750FVI to collect data, like temperature, humidity, atmospheric pressure, etc. These data will be read by the weather station via sensor every 5 seconds and uploaded to the Internet per 60 seconds, which enables you to grasp real-time data charts by your phone or computer. And it is available to modify the code to achieve different functions. Features: ESP8266: ESP8266-12E module Features with built-in CP2102 chip, micro USB, 4MB flash memory, complete I/O port and wireless 802.11 supported IOT platform, module replacement for Arduino. DHT11: This sensor is a calibrated temperature and humidity sensor with digital signal output. Simple communication protocol simplifies programming job, greatly reduces the programming effort required. BMP180: It is a high-precision, small-sized, super-low power sensor that has excellent performance, power consumption as low as 3μA, minimum absolute accuracy reaching 0.03 hPa, and pressure range of 300~1100hPa. BH1750FVI: BH1750FVI digital light intensity sensor adopts direct digital output, requires no complex calculation, omits calibration. LCD Display: 0.96-in SSD1306 yellow and blue OLED LCD display with I2C IIC SPI serial, has high resolution (128*64), provides clear viewing. Specifications: Material: Electronic Components Package Weight: 170g / 5.99oz Package Size: 14.5*8.8*4cm / 5.70*3.46*1.57in Note: Weather station kit only, other accessories in the picture are not included. Due to manual measurement, there may be deviation. Due to lighting, the picture and material object may slightly differ in color, please in kind prevail. Packing List: 1 * ESP8266-12E 1 * DHT11 1 * BMP180 1 * BH1750FVI 1 * OLED Display 1 * USB Cable 2 * Breadboard 20 * Dupont

0.96 inch 80x160 oled spi st7735 tft lcd description module for arduino esp8266 Specs and dimensions look at the pi