Lỗi driver máy cnc

External wide voltage input,12-24V,and anti-reverse function. Support various versions of MACH3 software and support the latest version. Support windows XP,WIN7,WIN8,WIN10,support for 64-bit systems,support laptops,support for tablet computers. All input signals are separated by light,and emergency stop,knife setting,limit,and zero return can be connected to ensure computer security.The input can be connected to a mechanical switch or a proximity switch (normally open with NPN). All the way through the optocoupler isolated 0-10V analog voltage output,you can control the 0-10V analog voltage input inverter,control the spindle speed. Provide PWM output (5V level),can be connected to the spindle speed controller controlled by PWM. Provide 4 output ports (5V level),can be connected with the optocoupler relay module,control water cooling, spray and so on. Maximum 100KHZ output per axis,can be connected to common anode or common cathode,input level is 5V,stepper or servo motor driver with optocoupler input (pulse + direction). At the same time provide 5-axis interface cable socket (XH2.54),easy to connect. Size:9x6cm/3.54x2.36inch Note: Please allow 1-3mm error due to manual measurement. pls make sure you do not mind before you bid Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you! Package Includes: 1x CNC USB MACH3 100Khz Breakout

Uses removable A4988 or DRV8825 compatible stepper drivers. The extension board can be used for carving machine, 3D printer driver expansion board. GRBL 0.8 compatible. (Open source firmware that runs on an for arduino UNO that turns G-code commands into stepper signals) PWM Spindle and direction pins,4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13) Compact design. Stepper Motors can be connected with 4 pin molex connectors or soldered in place. It is a total of four slots, can drive four A4988 stepper motor. Each road stepper motors only need two IO ports. In other words, six IO ports can be well managed three stepper motors. Very convenient to use. Parameters : dir direction control , dirPin corresponding stepper motor DIR pin , stepperPin corresponding stepper motor " step " pin , Step number of step of no return value. void step (boolean dir, byte dirPin, byte stepperPin, int steps); digitalWrite (dirPin, dir); delay (50); for (int i = 0; i Less Than steps; i + +); digitalWrite (stepperPin, HIGH); delayMicroseconds (800); digitalWrite (stepperPin, LOW); delayMicroseconds (800); UNO for Arduino module IO port correspondence introduction. UNO for Arduino---------------------- expansion board 8 ------------------------ EN ( stepper motor driver enable , active low ) 7 ----------------------- Z.DIR (Z -axis direction control ) 6 ----------------------- Y.DIR (Y -axis direction control ) 5 ----------------------- X.DIR (X -axis direction control ) 4 ---------------------- Z.STEP (Z -axis stepper control ) 3 ---------------------- Y.STEP (Y -axis stepper control ) 2 ---------------------- X.STEP (X -axis stepper control ) / / The following is a simple stepper motor control procedures, # define EN 8 / / stepper motor enable , active low # define X_DIR 5 / / X -axis stepper motor direction control # define Y_DIR 6 / / y -axis stepper motor direction control # define Z_DIR 7 / / z axis stepper motor direction control # define X_STP 2 / / x -axis stepper control # define Y_STP 3 / / y -axis stepper control # define Z_STP 4 / / z -axis stepper control Function : step . function: to control the direction of the stepper motor , the number of steps . Item Type:Motherboard colour:Picture color Material:PC Package Contents: 1 x CNC Shield Expansion Board Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

THÔNG SỐ KĨ THUẬT - Tương thích GRBL (mã nguồn mở chạy trên Arduino UNO R3 để điều khiển CNC mini) - Hỗ trợ lên tới 4 trục (trục X, Y, Z và một trục thứ tư tùy chọn) - Hỗ trợ tới 2 Endstop (cảm biến đầu cuối) cho mỗi trục - Tính năng điều khiển spindle - Tính năng điều khiển dung dịch làm mát khi máy hoạt động - Sử dụng các mô đun điều khiển động cơ bước, giúp tiết kiệm chi phí khi thay thế, nâng cấp - Thiết lập độ phân giải bước động cơ bằng jump đơn giản - Thiết kế nhỏ gọn, các đầu nối tiêu chuẩn thông dụng - Điện áp nguồn cấp đa dạng từ 12V tới 36V. - Kích thước 6.8x5.4cm. ************ CÔNG DỤNG SẢN PHẨM - CNC shield V3 là board mở rộng của Arduino UNO R3 dùng để điều khiển các máy CNC mini. - Board có 4 khay dùng để cắm các mô đun điều khiển động cơ bước A4988, khi đó board có thể điều khiển3 trục X, Y, Z và thêm một trục thứ 4 tùy chọn trên các máy CNC mini. ********** ♡ Linh Kiện Điện Tử TuHu ♡ ✦ Điện thoại: 0962425005 ✦Tư vấn kĩ thuật miễn phí.02466514142. ✦ Website: Mualinhkien.VN ✦ Zalo chủ shop: 0941344233. ✦Email: [email protected] ✦ Facebook Chủ Shop:https://www.facebook.com/TuHuGroup ✦Bán Hàng Cơ Sở: 0982725005. Nhận Làm Đồ Án Dự Án Điện Tử ✦Liên Hệ: 0962025005 Zalo: 0962025005 ✦Email: [email protected] ✦Fanpage TuHu : https://www.facebook.com/linhkiendientutuhu/?ref=bookmarks ✦Nhóm Facebook hỗ trợ khách hàng : https://www.facebook.com/groups/tuhusupport/?ref=bookmarks ✦Kênh youtube tuhu: https://www.youtube.com/channel/UCTnJ8z_qIDQ4gSDlSRoRXug ✦Facebook Chủ TuHu : https://www.facebook.com/mualinhkien ********** BHU http://mualinhkien.vn #tuhu #linhkiendientu #mualinhki

welcome to openwaterd.vn ★GIÁ RẺ★TMC2208 V1.2 Stepper Motor Driver Module For 3D Printer CNC Engraving Features: The Silent-Step-Stick is a Stepper Motor Driver Board for 2-Phase Motors based on a Trinamic TMC 2100, Trinamic TMC 2130or Trinamic TMC 2208. Hardware compatible with StepStick and Pololu A4988 Components on bottom PCB side for better heat emission, further infos here Trinamic stepper motor driver (chopper drive / constant current drive) Automatic standby current reduction MicroPlyer - microstep interpolator for increased smoothness of microstepping StealthChop - for quiet operation and smooth motion SpreadCycle - highly dynamic motor control chopper Extra features of TMC2130: SPI configuration interface (up to 4MHz) Up to 256 native microsteps (without interpolation) CoolStep - current control for energy savings StallGuard2 - sensorless motor load detection DcStep - load dependent speed control Automatic stealthChop and spreadCycle switchover depending on velocity Extra features of TMC2208: UART configuration interface (9600...500k Baud) Up to 256 native microsteps (without interpolation) StealthChop2 - faster motor acceleration/deceleration than stealthChop Automatic stealthChop and spreadCycle switchover depending on velocity Package Includes: 1 x TMC2208 Driver 1 x Heat Sink 1 x Screwdriver #Engraving #V1.2 #Motor #★GIÁ #For #Module #Stepper #Driver #Printer #CNC #RẺ★TMC2208 #3D #Module-For #★GIÁ-RẺ★TMC2208 #CNC-Engraving #Printer-CNC #RẺ★TMC2208-V1.2 #Motor-Dr

CNC Shield Board: Latest Arduino CNC Shield Version 3.0 GRBL 0.9 compatible 4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13) 2 x End stops for each axis (6 in total) Coolant enable Compatible with A4988 or DRV8825 stepper driver Operating voltage: 5V Digital I/O pins: 14 (including 6 with PWM capability) I-I/O pin output current: 40mA max 3.3V output current: 150mA max Flash memory: 32 kB (0.5kB used by bootloader - included) Static RAM (SRAM): 2 kB EEPROM: 1 kB Clock speed: 16MHz A4988 Stepper Motor Driver Board is a breakout board for Allegro's A4988 DMOS Micro-stepping Driver with Translator and Overcurrent Protection; Low RDS (On) Output Automatic current decay mode detection / selection Mix with slow current decay modes Synchronous rectification for low power dissipation Internal UVLO Crossover-current protection 3.3 and 5 V compatible logic supply Thermal shutdown circuitry Ground fault protection Load short-circuit protection Five selectable step modes: full, 1/2, 1/4, 1/8 and 1/16 Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. (More generally, rewiring anything while it is powered is asking for trouble). Color: blue + red Material: metal + PC Package Contents: 1 x CNC Shield Board 1 x UNO R3 Board for Arduino 4 x A4988 Stepper Motor Driver 4 x Heat Sink Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

CNC Shield Board: Latest CNC Shield Version 3.0 for Arduino.GRBL 0.9 compatible. (Open source firmware that runs on an UNO for Arduino that turns G-code commands into stepper signals).PWM Spindle and direction pins.4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13).2 x End stops for each axis (6 in total) Coolant enable,Uses removable A4988 or DRV8825 compatible stepper drivers Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping ).Compact design.Stepper Motors can be connected with 4 pin molex connectors or soldered in place. Runs on 12-36V DC. (At the moment only the DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.),Please note that this is an unassembled kit and Basic soldering skills are needed.A4988 Stepper Motor Driver Board is a breakout board for Allegro's A4988 DMOS Micro-stepping Driver with Translator and Overcurrent Protection; please read the A4988 datasheet carefully before using this product. Low RDS (On) Output,Automatic current decay mode detection / selection,Mix with slow current decay modes.Synchronous rectification for low power dissipation,Internal UVLO.Crossover-current protection,3.3 and 5 V compatible logic supply,Thermal shutdown circuitry,Ground fault protection,Load short-circuit protection,Five selectable step modes: full, 1/2, 1/4, 1/8 and 1/16. Colour: Photo Color Material: PC+ metal Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. (More generally, rewiring anything while it is powered is asking for trouble). Note: Green or Red PCB Package Includes: 1 x CNC Shield Board 4 x A4988 Stepper Motor Driver 4 x Heat Sink Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from thereal thing. The measurement allowed error is +/- 1

Do you want to enjoy high-quality experience? Then get into our store and pick it up.！ Decription: Features: Use removable A4988 or DRV8825 compatible stepping driver. The extension board can be used for engraving machine or 3D printer driver. Compatible with GRBL 0.8. Open-source firmware operated on Arduino UNO, converting G code command into stepping signal. PWM spindle and direction pin, 4 shaft support (X, Y, Z, A - you can copy X, Y, Z or use pin D12 and D13 customize firmware perform complete shaft 4). Compact design, stepping motor can connect 4 pin connectors or be soldered. This is a set of disassembled part, and you need basic soldering skills to solder them together. CNC Expansion Board: Version: V3.0 Green 68 x 53 x 18mm / 2.67 x 2.08 x 0.7" Voltage: DC 12V to 36V (only DRV8825 driver can handle up to 36V, so please consider voltage for power supply) 4pcs A4988 Driver: 20 x 15mm / 0.78 x 0.59" Thermal Shutdown Circuit: Yes Cross Current Protection: Yes Ground Fault Protection: Yes Short Circuit Protection: Yes Compatible Logic Voltage: 3.3V and 5V Five Step Modes: Full, 1/2, 1/4, 1/8 and 1/16 Mix with slow current attenuation model. Internal UVLO and low RDS (on) output. Automatic current attenuation mode Detection/Select. Phase-in rectifier, low power consumption. Warning: Connecting or disconnecting stepping motor while driver is powered on might damage driver. 4pcs Heat Sinks: 8 x 8mm / 0.31 x 0.31" Included: 1 x cnc shield v3 4 x A4988 4 x Hea

Features: 1. Low noise 2. Low calorie 3. Smooth operation 4. Good acceleration performance el: 23HS5628 Current/phase: 2.8A Holding torque: 12600g.cm Stage 2 el: Stepping motor Colour: black + sier Material: plastic + metal Size: 6.35mm/8mm Package Contents: 1 * 23HS5628 motor 1 * DM542 4.2A Stepper motor driver 1 * 30CM line<br />Only the above package content, other products are not included.<br />Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

THÔNG SỐ KĨ THUẬT - Tương thích GRBL (mã nguồn mở chạy trên Arduino UNO R3 để điều khiển CNC mini) - Hỗ trợ lên tới 4 trục (trục X, Y, Z và một trục thứ tư tùy chọn) - Hỗ trợ tới 2 Endstop (cảm biến đầu cuối) cho mỗi trục - Tính năng điều khiển spindle - Tính năng điều khiển dung dịch làm mát khi máy hoạt động - Sử dụng các mô đun điều khiển động cơ bước, giúp tiết kiệm chi phí khi thay thế, nâng cấp - Thiết lập độ phân giải bước động cơ bằng jump đơn giản - Thiết kế nhỏ gọn, các đầu nối tiêu chuẩn thông dụng - Điện áp nguồn cấp đa dạng từ 12V tới 36V. - Kích thước 6.8x5.4cm. ************ CÔNG DỤNG SẢN PHẨM - CNC shield V3 là board mở rộng của Arduino UNO R3 dùng để điều khiển các máy CNC mini. - Board có 4 khay dùng để cắm các mô đun điều khiển động cơ bước A4988, khi đó board có thể điều khiển3 trục X, Y, Z và thêm một trục thứ 4 tùy chọn trên các máy CNC mini. ********** ♡ Linh Kiện Điện Tử TuHu ♡ ✦ Điện thoại: 0962425005 ✦Tư vấn kĩ thuật miễn phí.02466514142. ✦ Website: Mualinhkien.VN ✦ Zalo chủ shop: 0941344233. ✦Email: [email protected] ✦ Facebook Chủ Shop:https://www.facebook.com/TuHuGroup ✦Bán Hàng Cơ Sở: 0982725005. Nhận Làm Đồ Án Dự Án Điện Tử ✦Liên Hệ: 0962025005 Zalo: 0962025005 ✦Email: [email protected] ✦Fanpage TuHu : https://www.facebook.com/linhkiendientutuhu/?ref=bookmarks ✦Nhóm Facebook hỗ trợ khách hàng : https://www.facebook.com/groups/tuhusupport/?ref=bookmarks ✦Kênh youtube tuhu: https://www.youtube.com/channel/UCTnJ8z_qIDQ4gSDlSRoRXug ✦Facebook Chủ TuHu : https://www.facebook.com/mualinhkien ********** BHU http://mualinhkien.vn #tuhu #linhkiendientu #mualinhki

Feature： Brand new and high quality. Product Features: Material: Electrical components Color: See pictures 42/57/86 TB6600 Stepper Motor 32-segment driver updated version 4.0A 40VDC for CNC milling machine Specifications: This unit is an upgraded version of TB6600, the breakdown of increase to 32 segments, for high targeting purposes. Applicable stepper motor: 42.57, 86 Phase type phase (4 wire 6 wire 8 wire line) 1. 9 V-42V DC power supply; 2. H-bridge Bipolar constant-phase flow-driven; 3. the maximum output current of 4.0A eight optional; 4. up to 32 segments of six types of sub-modes available; 5. the input signal is high-speed optical insulation; 6. standard common anode single pulse interface; 7. HOLD function offline; 8. semi-closed chassis can accommodate the most demanding environment; 9. provide semi-automatic current locking function; 10. built-in thermal protection and overcurrent protection. 11.Size: 9.6*5.5*2.7cm Package included: 1x TB6600 Single Axis 4A Stepper Motor Driver Controller 9~40V Micro-Step CNC Note: Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank

Aibecy 3D Printer Accessories CNC Shield UNO-R3 Board A4988 Driver Kit With Heat Sink For Arduino Engraver 3D Printer Features: CNC shield uses removable A4988 or DRV8825 compatible stepper drivers; the CNC shield extension board can be used for carving machine, 3D printer driver expansion board. GRBL 0.8 compatible. (Open source firmware that runs on an Arduino-UNO that turns G-code commands into stepper signals); PWM Spindle and direction pins,4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13). Small size and compact design, Stepper Motors can be connected with 4 pin molex connectors or soldered in place. A4988 Stepper Motor Driver mixes with slow current decay modes; internal UVLO and low RDS (on) output. Automatic current decay mode detection/selection; synchronous rectification for low power dissipation. Specifications: CNC Shield Board -- Version: 3.0 Color: red Size: 6.8 * 5.3 * 1.8cm / 2.68 * 2.09 * 0.71in VoltageL DC 12-36V (at the moment only the DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.) A4988 Stepper Motor Driver -- Color: red Size: 2 * 1.5 * 1cm / 0.79 * 0.59 * 0.39in Thermal Shutdown Circuitry: yes Crossover Fault Protection: yes Load Short-Circuit Protection: yes Compatible Logic Suppluy: 3.3V and 5V Five Selection Step Modes:full, 1/2, 1/4, 1/8, 1/16 UNO R3 -- Color: blue Size: 6.8 * 5.3cm / 2.68 * 2.09in Package Size: 15 * 11 * 4cm / 5.9 * 4.33 * 1.57in Package Weight: 90g / 3.17oz Note: This is an unassembled kit and Basic soldering skills are needed. Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. Package List: 1 * UNO-R3 Board 1 * CNC Shield Board 4 * A4988 Stepper Motor Driver 4 * Heat Sink 1 * USB Cable 1 * 40-Pin Row Needles #cncshieldboard #3dprinteraccessorie #ConsumerElectronics #3dprinterkitreprap #a4988drv8825 #controller #Printers #unor3board #steppermotordriver #3dpr

Uses removable A4988 or DRV8825 compatible stepper drivers. The extension board can be used for carving machine, 3 d printer driver expansion board GRBL 0.8 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals) PWM Spindle and direction pins,4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13) Compact design. Stepper Motors can be connected with 4 pin molex connectors or soldered in place. Voltage: DC 12~36 V Please note that this is an unassembled kit and Basic soldering skills are needed. DRV8825 Stepper Motor Driver The module has an interface pinout is almost the same with A4988 stepper motor drive carrier, so that it can be used as a higher performance in a pull-down menu the plates replaced in many applications. Features: Simple step and direction control interface The interface can connect directly with 3.3V and 5V systems Support over-temperature thermal shutdown, over-current shutdown and under-voltage lockout Support short-to-ground and shorted-load protection Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step 4-layer, 2 oz copper PCB for improved heat dissipation Adjustable current control support you to set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor's rated voltage to achieve higher step rates Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay) 45V maximum supply voltage Built-in regulator (needed external logic voltage supply) Colour:Color as shown Material:PCB board Package Contents: 1x CNC shielding plates 4x DRV8825 stepper motor driverOnly the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

Welcome to the [aurorawell] store Follow the store and enjoy the discount. Every week, creative new products are on the shelves. Selling is not the end, but the beginning of the promise! [Before ordering] Please read the dimensions and other related content carefully before purchasing. [shipment precautions] ✎The actual product is the same as the image displayed on the page. Shipped within 24 hours after delivery ✎ Normally, transportation takes 15-20 working days. ✎ Shipping costs are automatically displayed by the shopee system. Please contact the owner if you have any questions. I wish you a happy shopping! _______________❀Product Details❀_______ Features: CNC V3 Board: Detachable A4988 compatible stepper drive. The expansion board can be used for the engraving machine and the 3 d printer driver expansion board. GRBL 0.8 compatible. Open source firmware running for Arduino UNO, converting G code commands to step signals. PWM spindle and direction pins, 4-axis support (X, Y, Z, A- can copy X, Y, Z or make a complete 4th axis, using custom firmware, using pins D12 and D13). Compact design. The stepper motor can be connected or soldered into place with a 4-pin molex connector. Please note that this is an unassembled kit that requires basic welding skills. A4988 Stepper Motor Driver: A mixer with a slow current decay mode. Internal UVLO and low RDS (on) output. Automatic current decay mode detection/selection. Synchronous rectification, low power consumption. Warning: Connecting or disconnecting the stepper motor while the drive is powered may damage the drive. Specifications: CNC V3 Board: Color: Red Voltage: DC 12~36 V (At this time, only the DRV8825 driver can handle voltages up to 36V, so please consider the operating voltage when powering the board.) A4988 Stepper Motor Driver: Color: Red Thermal shutdown circuit: yes Cross current protection: yes Ground fault protection: yes Load short circuit protection: yes Compatible logic supplies: 3.3V and 5 V UNO R3 Board: Single chip microcomputer: ATmega328 Clock speed: 16 MHz USB interface: ATmega16U2 Operating voltage: 5 V I-I / O pin output current: up to 40 mA 3.3 V output current: up to 150 mA Digital I/O pins: 14 (including 6 PWM-capable pins) Analog input pin: 6 EEPROM: 1 kB Static RAM (SRAM): 2 kB Flash: 32 kB Package List: 1 * UNO R3 Board 1 * CNC Shield V3 Expansion Board 4 * A4988 Stepper Motor Driver 1 * 40-way Pin 1 * USB Ca

CNC shield V3 là board mở rộng của Arduino UNO R3 dùng để điều khiển các máy CNC mini. Board có 4 khay dùng để cắm các mô đun điều khiển động cơ bước A4988, khi đó board có thể điều khiển3 trục X, Y, Z và thêm một trục thứ 4 tùy chọn trên các máy CNC mini. Đặc điểm nổi bật: - Tương thích GRBL (mã nguồn mở chạy trên Arduino UNO R3 để điều khiển CNC mini) - Hỗ trợ lên tới 4 trục (trục X, Y, Z và một trục thứ tư tùy chọn) - Hỗ trợ tới 2 Endstop (cảm biến đầu cuối) cho mỗi trục - Tính năng điều khiển spindle - Tính năng điều khiển dung dịch làm mát khi máy hoạt động - Sử dụng các mô đun điều khiển động cơ bước, giúp tiết kiệm chi phí khi thay thế, nâng cấp - Thiết lập độ phân giải bước động cơ bằng jump đơn giản - Thiết kế nhỏ gọn, các đầu nối tiêu chuẩn thông dụng - Điện áp nguồn cấp đa dạng từ 12V tới 36V. Tương thích với module A4988 và DRV8825 Tương thích với module U

THÔNG SỐ KĨ THUẬT - Tương thích GRBL (mã nguồn mở chạy trên Arduino UNO R3 để điều khiển CNC mini) - Hỗ trợ lên tới 4 trục (trục X, Y, Z và một trục thứ tư tùy chọn) - Hỗ trợ tới 2 Endstop (cảm biến đầu cuối) cho mỗi trục - Tính năng điều khiển spindle - Tính năng điều khiển dung dịch làm mát khi máy hoạt động - Sử dụng các mô đun điều khiển động cơ bước, giúp tiết kiệm chi phí khi thay thế, nâng cấp - Thiết lập độ phân giải bước động cơ bằng jump đơn giản - Thiết kế nhỏ gọn, các đầu nối tiêu chuẩn thông dụng - Điện áp nguồn cấp đa dạng từ 12V tới 36V. - Kích thước 6.8x5.4cm. ************ CÔNG DỤNG SẢN PHẨM - CNC shield V3 là board mở rộng của Arduino UNO R3 dùng để điều khiển các máy CNC mini. - Board có 4 khay dùng để cắm các mô đun điều khiển động cơ bước A4988, khi đó board có thể điều khiển3 trục X, Y, Z và thêm một trục thứ 4 tùy chọn trên các máy CNC mini. ********** ♡ Linh Kiện Điện Tử TuHu ♡ ✦ Điện thoại: 0962425005 ✦Tư vấn kĩ thuật miễn phí.02466514142. ✦ Website: Mualinhkien.VN ✦ Zalo chủ shop: 0941344233. ✦Email: [email protected] ✦ Facebook Chủ Shop:https://www.facebook.com/TuHuGroup ✦Bán Hàng Cơ Sở: 0982725005. Nhận Làm Đồ Án Dự Án Điện Tử ✦Liên Hệ: 0962025005 Zalo: 0962025005 ✦Email: [email protected] ✦Fanpage TuHu : https://www.facebook.com/linhkiendientutuhu/?ref=bookmarks ✦Nhóm Facebook hỗ trợ khách hàng : https://www.facebook.com/groups/tuhusupport/?ref=bookmarks ✦Kênh youtube tuhu: https://www.youtube.com/channel/UCTnJ8z_qIDQ4gSDlSRoRXug ✦Facebook Chủ TuHu : https://www.facebook.com/mualinhkien ********** BHU http://mualinhkien.vn #tuhu #linhkiendientu #mualinhki

We have many products in our warehouse, our warehouse is in Shenzhen . Genaral it need 1-2weeks arrive your hand. if you subimit order , we will handle in 1-3days.if you chat with us , we donot reply you, donot worry , we are try to handle your order.so pls donot cancel o

We have many products in our warehouse, our warehouse is in Shenzhen . Genaral it need 1-2weeks arrive your hand. if you subimit order , we will handle in 1-3days.if you chat with us , we donot reply you, donot worry , we are try to handle your order.so pls donot cancel o

Aibecy 3D Printer Accessories CNC Shield R3 Board A4988 Driver Kit With Heat Sink For Engraver 3D Printer Features: CNC shield uses removable A4988 or DRV8825 compatible stepper drivers; the CNC shield extension board can be used for carving machine, 3D printer driver expansion board. GRBL 0.8 compatible. (Open source firmware that runs on an board that turns G-code commands into stepper signals); PWM Spindle and direction pins,4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13). Small size and compact design, Stepper Motors can be connected with 4 pin molex connectors or soldered in place. A4988 Stepper Motor Driver mixes with slow current decay modes; internal UVLO and low RDS (on) output. Automatic current decay mode detection/selection; synchronous rectification for low power dissipation. Specifications: CNC Shield Board -- Version: 3.0 Color: red Size: 6.8 * 5.3 * 1.8cm / 2.68 * 2.09 * 0.71in VoltageL DC 12-36V (at the moment only the DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.) A4988 Stepper Motor Driver -- Color: red Size: 2 * 1.5 * 1cm / 0.79 * 0.59 * 0.39in Thermal Shutdown Circuitry: yes Crossover Fault Protection: yes Load Short-Circuit Protection: yes Compatible Logic Suppluy: 3.3V and 5V Five Selection Step Modes:full, 1/2, 1/4, 1/8, 1/16 UNO R3 -- Color: blue Size: 6.8 * 5.3cm / 2.68 * 2.09in Package Size: 15 * 11 * 4cm / 5.9 * 4.33 * 1.57in Package Weight: 90g / 3.17oz Note: This is an unassembled kit and Basic soldering skills are needed. Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. Package List: 1 * R3 Board 1 * CNC Shield Board 4 * A4988 Stepper Motor Driver 4 * Heat Sink 1 * USB Cable 1 * 40-Pin Row Ne

We have many products in our warehouse, our warehouse is in Shenzhen . Genaral it need 1-2weeks arrive your hand. if you subimit order , we will handle in 1-3days.if you chat with us , we donot reply you, donot worry , we are try to handle your order.so pls donot cancel o

Welcome:❥Feature： Brand new and high quality. Product Features: Material: Electrical components Color: See pictures 42/57/86 TB6600 Stepper Motor 32-segment driver updated version 4.0A 40VDC for CNC milling machine Specifications: This unit is an upgraded version of TB6600, the breakdown of increase to 32 segments, for high targeting purposes. Applicable stepper motor: 42.57, 86 Phase type phase (4 wire 6 wire 8 wire line) 1. 9 V-42V DC power supply; 2. H-bridge Bipolar constant-phase flow-driven; 3. the maximum output current of 4.0A eight optional; 4. up to 32 segments of six types of sub-modes available; 5. the input signal is high-speed optical insulation; 6. standard common anode single pulse interface; 7. HOLD function offline; 8. semi-closed chassis can accommodate the most demanding environment; 9. provide semi-automatic current locking function; 10. built-in thermal protection and overcurrent protection. 11.Size: 9.6*5.5*2.7cm Package included: 1x TB6600 Single Axis 4A Stepper Motor Driver Controller 9~40V Micro-Step CNC Note: Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank

Uses removable A4988 or DRV8825 compatible stepper drivers. The extension board can be used for carving machine, 3 d printer driver expansion board GRBL 0.8 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals) PWM Spindle and direction pins,4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13) Compact design. Stepper Motors can be connected with 4 pin molex connectors or soldered in place. Voltage: DC 12~36 V Please note that this is an unassembled kit and Basic soldering skills are needed. DRV8825 Stepper Motor Driver The module has an interface pinout is almost the same with A4988 stepper motor drive carrier, so that it can be used as a higher performance in a pull-down menu the plates replaced in many applications. Features: Simple step and direction control interface The interface can connect directly with 3.3V and 5V systems Support over-temperature thermal shutdown, over-current shutdown and under-voltage lockout Support short-to-ground and shorted-load protection Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step 4-layer, 2 oz copper PCB for improved heat dissipation Adjustable current control support you to set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor's rated voltage to achieve higher step rates Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay) 45V maximum supply voltage Built-in regulator (needed external logic voltage supply) Colour:Color as shown Material:PCB board Package Contents: 1x CNC shielding plates 4x DRV8825 stepper motor driverOnly the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

Welcome to Homeliving shop, enjoy your shopping moment! Please consult our customer service if you have any problems in the process of shopping, thank you!Feature： Brand new and high quality. Product Features: Material: Electrical components Color: See pictures 42/57/86 TB6600 Stepper Motor 32-segment driver updated version 4.0A 40VDC for CNC milling machine Specifications: This unit is an upgraded version of TB6600, the breakdown of increase to 32 segments, for high targeting purposes. Applicable stepper motor: 42.57, 86 Phase type phase (4 wire 6 wire 8 wire line) 1. 9 V-42V DC power supply; 2. H-bridge Bipolar constant-phase flow-driven; 3. the maximum output current of 4.0A eight optional; 4. up to 32 segments of six types of sub-modes available; 5. the input signal is high-speed optical insulation; 6. standard common anode single pulse interface; 7. HOLD function offline; 8. semi-closed chassis can accommodate the most demanding environment; 9. provide semi-automatic current locking function; 10. built-in thermal protection and overcurrent protection. 11.Size: 9.6*5.5*2.7cm Package included: 1x TB6600 Single Axis 4A Stepper Motor Driver Controller 9~40V Micro-Step CNC Note: Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank

We have many products in our warehouse, our warehouse is in Shenzhen . Genaral it need 1-2weeks arrive your hand. if you subimit order , we will handle in 1-3days.if you chat with us , we donot reply you, donot worry , we are try to handle your order.so pls donot cancel o

THÔNG SỐ KĨ THUẬT - Điện áp nuôi Main từ 3.3V đến 5V. - Điện áp điều khiển Motor từ 8V đến 35V. - Kích thước nhỏ gọn:15mm x 20mm x 2 mm. - Điều khiển 5 chế độ: full step, 1/2step, 1/4step, 1/8step, 1/16step. - Công suất tải motor từ 0.5A đến 1.5. - Điều chỉnh dòng ra bằng triết áp, nằm bên trên Current Limit = VREF x 2.5. - Tự động ngắt khi bị quá tải nhiệt. ************ CÔNG DỤNG SẢN PHẨM - Module A4988 là driver điều khiển động cơ bước cực kì nhỏ. - Hỗ trợ nhiều chế độ làm việc. - Điều chỉnh được dòng ra cho động cơ. - Tự động ngắt điện khí quá nóng. - Dùng cho mạch điều khiển động cơ bước.... - Dùng cho cách mạch như CNC, máy in, robot... - Dùng làm mạch nghiên cứu thực hành điện tử. ********** ♡ Linh Kiện Điện Tử TuHu ♡ ✦ Điện thoại: 0962425005 ✦Tư vấn kĩ thuật miễn phí.02466514142. ✦ Website: Mualinhkien.VN ✦ Zalo chủ shop: 0941344233. ✦Email: [email protected] ✦ Facebook Chủ Shop:https://www.facebook.com/TuHuGroup ✦Bán Hàng Cơ Sở: 0982725005. Nhận Làm Đồ Án Dự Án Điện Tử ✦Liên Hệ: 0962025005 Zalo: 0962025005 ✦Email: [email protected] ✦Fanpage TuHu : https://www.facebook.com/linhkiendientutuhu/?ref=bookmarks ✦Nhóm Facebook hỗ trợ khách hàng : https://www.facebook.com/groups/tuhusupport/?ref=bookmarks ✦Kênh youtube tuhu: https://www.youtube.com/channel/UCTnJ8z_qIDQ4gSDlSRoRXug ✦Facebook Chủ TuHu : https://www.facebook.com/mualinhkien ********** BHU http://mualinhkien.vn #tuhu #linhkiendientu #mualinhki

___________________❀Alwaysonline❀___________________ Welcome to our store, we insist on the lowest price to sell the best quality items. ✔Ready Stock ✔Wholesale Price ✔Quality Checked ★Surprises for you★ ☞Shop Voucher: Get More Discount ☞Follow Shop: Free Gifts ☞“Like” Items: Priority Shipping ( Sent us follow shop screenshot and remark on your order "Free Gift", if not will miss) ★★Attention Please★★ ✌We will be based on your guests in your country to send the corresponding adapter plug. _______________❀Product Information❀______________ Features: CNC V3 Board: Detachable A4988 compatible stepper drive. The expansion board can be used for the engraving machine and the 3 d printer driver expansion board. GRBL 0.8 compatible. Open source firmware running for Arduino UNO, converting G code commands to step signals. PWM spindle and direction pins, 4-axis support (X, Y, Z, A- can copy X, Y, Z or make a complete 4th axis, using custom firmware, using pins D12 and D13). Compact design. The stepper motor can be connected or soldered into place with a 4-pin molex connector. Please note that this is an unassembled kit that requires basic welding skills. A4988 Stepper Motor Driver: A mixer with a slow current decay mode. Internal UVLO and low RDS (on) output. Automatic current decay mode detection/selection. Synchronous rectification, low power consumption. Warning: Connecting or disconnecting the stepper motor while the drive is powered may damage the drive. Specifications: CNC V3 Board: Color: Red Voltage: DC 12~36 V (At this time, only the DRV8825 driver can handle voltages up to 36V, so please consider the operating voltage when powering the board.) A4988 Stepper Motor Driver: Color: Red Thermal shutdown circuit: yes Cross current protection: yes Ground fault protection: yes Load short circuit protection: yes Compatible logic supplies: 3.3V and 5 V UNO R3 Board: Single chip microcomputer: ATmega328 Clock speed: 16 MHz USB interface: ATmega16U2 Operating voltage: 5 V I-I / O pin output current: up to 40 mA 3.3 V output current: up to 150 mA Digital I/O pins: 14 (including 6 PWM-capable pins) Analog input pin: 6 EEPROM: 1 kB Static RAM (SRAM): 2 kB Flash: 32 kB Package List: 1 * UNO R3 Board 1 * CNC Shield V3 Expansion Board 4 * A4988 Stepper Motor Driver 1 * 40-way Pin 1 * USB Ca

THÔNG SỐ KĨ THUẬT - Tương thích GRBL (mã nguồn mở chạy trên Arduino UNO R3 để điều khiển CNC mini) - Hỗ trợ lên tới 4 trục (trục X, Y, Z và một trục thứ tư tùy chọn) - Hỗ trợ tới 2 Endstop (cảm biến đầu cuối) cho mỗi trục - Tính năng điều khiển spindle - Tính năng điều khiển dung dịch làm mát khi máy hoạt động - Sử dụng các mô đun điều khiển động cơ bước, giúp tiết kiệm chi phí khi thay thế, nâng cấp - Thiết lập độ phân giải bước động cơ bằng jump đơn giản - Thiết kế nhỏ gọn, các đầu nối tiêu chuẩn thông dụng - Điện áp nguồn cấp đa dạng từ 12V tới 36V. - Kích thước 6.8x5.4cm. ************ CÔNG DỤNG SẢN PHẨM - CNC shield V3 là board mở rộng của Arduino UNO R3 dùng để điều khiển các máy CNC mini. - Board có 4 khay dùng để cắm các mô đun điều khiển động cơ bước A4988, khi đó board có thể điều khiển3 trục X, Y, Z và thêm một trục thứ 4 tùy chọn trên các máy CNC mini. ********** ************ ♡ Linh Kiện Điện Tử H2 ♡ ✦ Điện thoại: 0582004297 ✦ Tư vấn kĩ thuật miễn phí.0582004297 ✦ Zalo chủ shop: 0582004297 ✦ Email:[email protected] ✦ Facebook Chủ Shop:https://www.facebook.com/profile.php?id=100064714623364 ✦ Bán Hàng Cơ Sở: 0393271

THÔNG SỐ KĨ THUẬT - Điện áp nuôi Main từ 3.3V đến 5V. - Điện áp điều khiển Motor từ 8V đến 35V. - Kích thước nhỏ gọn:15mm x 20mm x 2 mm. - Điều khiển 5 chế độ: full step, 1/2step, 1/4step, 1/8step, 1/16step. - Công suất tải motor từ 0.5A đến 1.5. - Điều chỉnh dòng ra bằng triết áp, nằm bên trên Current Limit = VREF x 2.5. - Tự động ngắt khi bị quá tải nhiệt. ************ CÔNG DỤNG SẢN PHẨM - Module A4988 là driver điều khiển động cơ bước cực kì nhỏ. - Hỗ trợ nhiều chế độ làm việc. - Điều chỉnh được dòng ra cho động cơ. - Tự động ngắt điện khí quá nóng. - Dùng cho mạch điều khiển động cơ bước.... - Dùng cho cách mạch như CNC, máy in, robot... - Dùng làm mạch nghiên cứu thực hành điện tử. ********** ♡ Linh Kiện Điện Tử TuHu ♡ ✦ Điện thoại: 0962425005 ✦Tư vấn kĩ thuật miễn phí.02466514142. ✦ Website: Mualinhkien.VN ✦ Zalo chủ shop: 0941344233. ✦Email: [email protected] ✦ Facebook Chủ Shop:https://www.facebook.com/TuHuGroup ✦Bán Hàng Cơ Sở: 0982725005. Nhận Làm Đồ Án Dự Án Điện Tử ✦Liên Hệ: 0962025005 Zalo: 0962025005 ✦Email: [email protected] ✦Fanpage TuHu : https://www.facebook.com/linhkiendientutuhu/?ref=bookmarks ✦Nhóm Facebook hỗ trợ khách hàng : https://www.facebook.com/groups/tuhusupport/?ref=bookmarks ✦Kênh youtube tuhu: https://www.youtube.com/channel/UCTnJ8z_qIDQ4gSDlSRoRXug ✦Facebook Chủ TuHu : https://www.facebook.com/mualinhkien ********** BHU http://mualinhkien.vn #tuhu #linhkiendientu #mualinhki

Latest For CNC Shield Version 3.0 for Arduino GRBL 0.9 compatible (Open source firmware that runs on an UNO for Arduino that turns G-code commands into stepper signals) 4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13) Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping ) A4988 Stepper Motor Driver Board is a breakout board for Allegro's A4988 DMOS Micro-stepping Driver with Translator and Overcurrent Protection; please read the A4988 datasheet carefully before using this product Specifications: CNC Shield Board: 1. PWM Spindle and direction pins 2. 2 x End stops for each axis (6 in total) 3. Coolant enable 4. Uses removable A4988 or DRV8825 compatible stepper drivers 5. Compact design 6. Stepper Motors can be connected with 4 pin molex connectors or soldered in place 7. Runs on 12-36V DC. (At the moment only the DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.) 8. Please note that this is an unassembled kit and Basic soldering skills are needed A4988 Stepper Motor Driver: 1. Low RDS (On) Output 2. Automatic current decay e detection / selection 3. Mix with slow current decay es 4. Synchronous rectification for low power dissipation 5. Internal UVLO 6. Crossover-current protection 7. 3.3 and 5 V compatible logic supply 8. Thermal shutdown circuitry 9. Ground fault protection 10. Load short-circuit protection 11. Five selectable step es: full, 1/2, 1/4, 1/8 and 1/16 12. Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. (More generally, rewiring anything while it is powered is asking for trouble) colour: as shown Material: PCB size: 11x6x2cm Package Contents: 1 x Shield Board For CNC 4 x A4988 Stepper Motor Driver (Green) 4 x Mini Heat Sink / 1 x Shield Board For CNC 4 x A4988 Stepper Motor Driver (Red) 4 x Mini HeatSink<br />Only the above package content, other products are not included.<br />Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

Description Item type: tool Input voltage:DC20-50V Maximum frequency:200KHz Output current:7 selections of 0.50-5.60A via DIP switches;or any value of 0.1-11. 5.60A via software configuration Size: 11.7*8.5cm/4.61*3.35inch Package includes: 1 x DM556 stepper motor driver Note: Please allow 1-3mm error due to manual measurement. pls make sure you do not mind before you bid:; Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank

Description: External wide voltage input,12-24V,and anti-reverse function. Support various versions of MACH3 software and support the latest version. Support windows XP,WIN7,WIN8,WIN10,support for 64-bit systems,support laptops,support for tablet computers. All input signals are separated by light,and emergency stop, setting,limit,and zero return can be connected to ensure computer security.The input can be connected to a mechanical switch or a proximity switch (normally open with NPN). All the way through the optocoupler isolated 0-10V analog voltage output,you can control the 0-10V analog voltage input inverter,control the spindle speed. Provide PWM output (5V level),can be connected to the spindle speed controller controlled by PWM. Provide 4 output ports (5V level),can be connected with the optocoupler relay ule,control water cooling, spray and so on. Maximum 100KHZ output per axis,can be connected to common anode or common cathode,input level is 5V,stepper or servo motor driver with optocoupler input (pulse + direction). At the same time provide 5-axis interface cable socket (XH2.54),easy to connect. Size: 9x6cm/3.54x2.36inch Motor Type: Other Color: green Material: PC + Metal Package Contents: 1 * CNC USB MACH3 100Khz Breakout Board 1 * USB CableOnly the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1