Cảm biến nhiệt máy in 3d

Cảm biến có giá trị điện trở thay đổi theo nhiệt độ môi trường, giúp bộ điều khiển xác định được nhiệt độ của đầu in. Phân loại: Có 4 loại không Jack cắm và có Jack khác nhau phù hợp với các loại Board mạch để quý khách lựa chọn. Nhấn chọn phân loại để thấy hình sản phẩm. Thông số kỹ thuật: - Điện trở tại 25°C: 100K - Hệ số Beta: B25/ 50 = 3950K - Sai số: ± 1% - Khoảng nhiệt độ đo được: -40°C ~ +300°C - Đường kính cảm biến: 1,05mm - Chiều dài (sau khi nối dây): 100cm #2004 #RAMPS1.4 #Mayin3D #3D #3DPrinter #PLA #ABS #Adruino #2560 #12864 #A4988 #MKSGen #DIY #Prusa #E3D #MK8 #cambien

(cer)HT-NTC100K Thermistor Temperature Sensor For 3D Printer 350 Degrees HotendSpecifications: Negative Temperature Coefficient (NTC) Thermistor Model: B3950 Temperature measurement head size: 3 * 15mm 1. Upgrade from the original ordinary temperature probe directly exposed temperature measurement to resistance package temperature measurement. Temperature measurement head cylinder diameter 3mm, length 15mm, can be used with the heating block that support the thermocouple.   2. The temperature measurement range is increased from -50 ℃~ +250℃ to -50 ℃ ~ +350 ℃. It helps a lot to print high-temperature filament, can replace the original K-type thermocouple temperature. If need to print high-temperature filament, the HT-NTC100K thermistors are highly recommended. 3. The new version of HT-NTC100K temperature measuring thermistor adopts 304 stainless steel, with the internal temperature package to ensure the maximum service life with precision temperature measurement.   4. HT-NTC100K thermistor adopts white high-temperature cord, can bear higher temperature. And for customers' convenience, the wires adopts line connection, the customer can tear the wires depends on their application. The high temperature line is double thicker than others in the market, not easy to break off.   5. Supports the customization of different specifications, including the temperature head cylinder size, length of the wires (MOQ is 100 sets).   6. Can be used with the new version of the heater (the new heater can heat up to 350 degrees). Package included

set2: 1 x copper heating block + 1 x Sensor ule 1.Place the IR-sensor on the top of the Extruder-body and secure it with the M2x8. 2.Tighten the M2x8 screw, the sensor shouldn't be able to move, but be careful the PCB isn't indestructible ;) 3.Connect the cable, mind the correct orientation of the connector and wires. 4.Leave a slack behind the sensor like in the picture. Don't create too big loop as it might interfere with the frame. If needed adjust the length by gently pulling/pushing the cable. Item Type: Heated Block el Number: copper heater block The new sensor is using the optical sensor which is triggered by a simple mechanical lever. This sensor doesn't care about the optical properties of the filament (it can be completely invisible) and cannot die because of mechanical wear. How to match: 1 A2 Hardened Steel V6 Nozzles,click here 2 high quality V6 titanium alloy heat break TC4,click here 3 Thermistor Cartridge 350 degrees,click here 4 Thermistor Cartridge pt1000,click here colour:copper/Black Material:copper/metal + plastic copper heating block size:22MM x 16MM x 11.5mm Package Contents: 1 x copper heating block 1 x Sensor uleOnly the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

Thông số: Tên sản phẩm: bộ điều khiển nhiệt độ kỹ thuật số chính xác cao Thông số kỹ thuật: XH - W1411 Phạm vi đo nhiệt độ: 55 ~ + 110 ° Độ chính xác đo nhiệt độ: cộng hoặc trừ 0,3 ° Độ phân giải: 0,1 ° Phạm vi kiểm soát nhiệt độ: - 19 ~ 99 ° Độ chính xác: 1 ° Đầu dò đo nhiệt độ: Đầu dò chống thấm nước tiêu chuẩn 1 mét NTC10K / B3950 Nguồn điện áp: DC12V AC220V Màu hiển thị: đỏ, xanh lá, xanh dương và vàng (tùy chọn) Môi trường áp dụng: - 25 đến 55 độ / 20% - 80% (RH) Loại đầu ra: Đầu ra rơle 20A Kích thước xuất hiện: 90 * 60 mm Kích thước lỗ: 70 * 50 mm Cách sử dụng: 1. tác giả sản phẩm phích cắm màn hình hiển thị nhiệt độ trên ổ cắm gia đình, minh họa nguồn điện được kết nối đúng cách 2. đặt đầu dò nhiệt độ cần kiểm soát nhiệt độ, theo nhu cầu để thiết lập nhiệt độ bắt đầu và dừng 3. phích cắm cung cấp điện của thiết bị sưởi hoặc làm mát trên bộ điều khiển nhiệt độ ổ cắm có thể được thực hiện Chú ý: Hãy nhớ đọc kỹ hướng dẫn sử dụng này trước tiên để sử dụng sản phẩm này 1. sản phẩm này là một ba phích cắm, vui lòng cắm với dây nối đất 2. máy chủ điều nhiệt không thấm nước, tránh nước, không được mang vào phòng tắm để sử dụng hoặc sử dụng ngoài trời 3. sử dụng công suất lớn hơn sản phẩm bị cấm công suất danh nghĩa hoặc gây ra thiệt hại vĩnh viễn và nguy hiểm 4. kiểm soát nhiệt độ thực tế nên chú ý quan sát xem kiểm soát nhiệt độ có được thực hiện chính xác hay không trước khi rời đi Đóng gói: 1 x XH-W1411 LCD Ba màn hình Bộ điều nhiệt kỹ thuật số Bộ điều khiển nhiệt độ đa chức năng Cảm biến -55 ~ 120 độ C AC110-220

<div><p>Resistance Temperature Coefficient-2-5%/ Max Rated Power45mW Suggested ParametersR25=100K B25/50=3950K(±1%) Temperature Range-40+300 Resistance Accuracy±1%±2%,±3% B Accuracy±1% Package Include : 5/10 pcs Thermistors cables</p><

5pcs 100K ohm NTC 3950 Thermistors Sensors with Cable 3D Printers Parts For Reprap Mend Part Temperature Accessories ●Name：5PCS 100K ohm NTC 3950 Thermistors Sensors with Cable 3D Printers Parts.（No Dupont） ● Resistance Accuracy：±1%，±2%,±3%. ● B Accuracy：±1%. ● Temperature Range：-40℃～+300℃. ● Max Rated Power：45mW. ● Resistance Temperature Coefficient：-2～-5%/℃. ● Suggested Parameters：R25℃=100K B25/50=3950K(

Cảm biến nhiệt độ cho máy in 3D với dây kết nối dài và được gắn với đầu kết nối 2.54 tiện lợi sử dụng các mạch điều khiển thế hệ

Cảm biến nhiệt độ cho máy in 3D có dây Sản phẩm được cung cấp bởi shop linh kiện điện tử Giải Pháp Chung, bạn có thể liên hệ với nhà bán hàng để có thêm thông tin chi tiết. H ì n h ả n h s ả n p h ẩ m đ ư ợ c c h ụ p t r ự c t i ế p đ ú n g n h ư h ì n h ả n h đ ă n g t ả i. G i a o h à n g n h a n h c h ó n g t r ê n t o à n q u ố c. Xem các sản phẩm khác tại đây W e b s i t e: h t t p s : / / g i a i p h a p c h u n g . V n Đ ị a c h ỉ : 18/655 Nguyễn Văn Linh, Phường Vĩnh Niệm, Quận Lê Chân, Thành phố Hải Phòng E m a i l : g i a i p h a p c h u n g 6 8 @ g m a i l . C o m H o t l i n e : 0936 824

Creality 3D NTC 3950 100K Ohm Thermistor Sensor with 0.7 Meter Wiring Cale and Female Pin Head for Ender-3 3D Printer Heatbed Hot End Replacement Part Features: This NTC 3950 100K Ohm Thermistor for Ender-3 or other compatible 3D printers heat bed & extruder. 100K ohm temperature sensor. With female pin head for connecting easily. Comes with 0.7m high temperature insulated wire. Made of high-quality material, not easy to break and long durability. Specifications: Resistance: at 25°C=100K ohm Cable Length: Approx. 0.7m Package Size: 13 * 9 * 1cm / 5.1 * 3.5 * 0.4in Package Weight: 8.6g / 0.3oz Package List: 1 * Thermistor #thermistorsensor #thermistortemperaturesensor #100kntcthermistor #ntc3950thermistorsensor #3905100k #3dprinterthermistorsensor #thermistor3dprinter #thermistor #100k3950thermistor #100kohmthermistors

By using progressively designed solenoid and hall sensor,It can integrate high precision in such a simple structure. pushing hard on the push-pin can damage Press sensorand make it less accurate. Fix push-pin with locking paint after reassembling or adjusting core. Do not remove or deform elastic material attached on the push-pin. No matter how bad your 3D printer is. The sensor is still working Voltage : 5V Current : 15mA Maximum(Peak) Current : 300mA Case Material : Polycarbonat(PC) Case Color : Semitransparent White Cable Length : 150mm Colour:Photo Color Material:Plastic + aluminum Package Contents: 1* set Press Auto Bed Leveling sensorOnly the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

For 3D-Touch V3.2 is the new generation hotbed automatic leveling accessory of FDM 3D printer. Built by the latest technology, it can accurately measure the inclination of the hotbed. It can be used for hotbeds made of glass, wood, metal, etc. Users no longer need to manually level the hotbed, bringing users a simpler and faster hot bed leveling experience, and improving the printing success rate and printing accuracy. Equipped with new structural design for higher precision, for 3D-Touch V3.2 can be widely used in various FDM 3D printers, it is a necessary accessory for 3D printers. New structural design, higher precision High precision, accuracy deviation is 0.01mm Suitable for various materials hotbeds Automatic detection after power on Abnormal alarm More stable and reliable Intelligent measurement Voltage: 4.8~5.1V Current: 15mA~300mA Colour: white Material: ABS+metal Package Contents: 1 * Automatic leveling sensor 4 * M3 screws 2 * M3 nuts 1 * 18cm cable 1 * 100cm cable 1 * Metal bracketOnly the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

Trong quá trình lưu thông trên đường phố không ai mong muốn xảy ra các sự cố đối với chiếc xe thân yêu của mình. Steelmatevietnam chúng tôi ở đây để cung cấp các giải pháp cho bạn tránh khỏi các rủi ro đó cũng như khắc phục sự cố đã xảy ra một cách an toàn, tiện lợi, nhanh chóng nhất bằng các sản phẩm chính hãng STEELMATE cao cấp, thông minh! Các vấn đề về lốp xe luôn để lại những hậu quả to lớn và cũng thường hay xảy ra. Chính vì vậy, theo dõi áp suất lốp xe thường xuyên sẽ giúp bạn ngăn ngừa những sự cố liên quan đến lốp. Bạn sẽ hoàn toàn yên tâm khi đã có Cảm biến áp suất lốp van trong TPMS không dây chính hãng STEELMATE có màn hình màu hiển thị thông số của STEELMATE OFFICIAL STORE chúng tôi -------------------------------------------------------------------- ***ĐẶC ĐIỂM NỔI BẬT*** - Thương hiệu STEEL MATE phân phối chính hãng duy nhất tại Shopee STEELMATE OFFICIAL STORE - Bảo hành 12 tháng chính hãng - Một đổi một trong 30 ngày - Phiên bản quốc tế tiếng Anh kèm giấy hướng dẫn sử dụng và lắp đặt bằng tiếng Anh và tiếng Việt - Chip xử lý cao cấp sử dụng công nghệ tiên tiến từ Cộng hòa Liên bang Đức, cho tốc độ xử lý nhanh và ổn định, cập nhật dữ liệu theo thời gian thực - Màn hình LCD màu được lắp đặt trên taplo xe, hiển thị sắc nét thông số về nhiệt độ và áp suất của từng lốp xe - Kết nối hoàn toàn không dây giữa màn hình hiển thị và cảm biến áp suất lốp - Tích hợp pin sạc năng lượng mặt trời và nguồn bổ sung từ dây USB nối nguồn oto 12V hoặc 5V - Cảnh báo khi nhiệt độ lốp - áp suất lốp quá cao hoặc quá thấp - Đặt chứng chỉ CE (châu Âu) và chứng chỉ FCC (Hoa Kỳ) - Tuổi thọ pin lên tới 5 năm - Cảnh báo âm thanh hình ảnh nhấp nháy khi van áp suất gặp sự cố --------------------------------------------------------------------- ***THÔNG SỐ KỸ THUẬT*** - Kích thước: 95mm*62mm*30mm - Nhiệt độ làm việc: -40°C+80°C . - HUD cảnh báo chạy bằng pin sạc (qua cổng USB) và năng lượng mặt trời (nguồn sạc bổ sung) - Tuổi thọ pin của bộ phận cảm biến lên đến 2 năm - Độ chính xác: ±1.5PSI (±0.1bar) - Độ chính xác nhiệt độ: ±3°C. - Phạm vi kiểm tra áp suất: 0-116psi (0-8bar). - Tuổi thọ pin cao~ 5 năm ----------------------------------------------------------------------- BẢO HÀNH CHÍNH HÃNG 12 THÁNG TOÀN QUỐC Sản phẩm chỉ có tại: STEELMATE OFFICIAL STORE Thương hiệu : STEELMATE Sản xuất tại: Đài Loan STEELMATE OFFICIAL STORE CAM KẾT: Sản phẩm 100% chính hãng, 100% giống như mô tả cũng như hình ảnh. Mọi thắc mắc liên quan đến sản phẩm, quy trình mua hàng, vận chuyển, bảo hành... Quý khách vui lòng CHAT với shop để được tư vấn tận tình và nhanh chóng nhất! STEELMATE OFFICIAL STORE rất hân hạnh được phục vụ! -------------------------------------------------------------------------- #cambienapsuatlop #cambientpms #cambienloptpms #cam_bien #cambienapsuat #cam_bien_ap_suat #cambienapsuatlop #cam_bien_ap_suat_lop #TPMS #phukienxehoi #steelmate #steel

<div><p>Resistance Accuracy±1%±2%,±3% B Accuracy±1% Suggested ParametersR25=100K B25/50=3950K(±1%) Temperature Range-40+300 Package Include : 5/10 pcs Thermistors cables Max Rated Power45mW Resistance Temperature Coefficient-2-5%/</p><

Upgrade HT-NTC100K thermistor: The temperature measuring head cylinder has a diameter of 3mm and a length of 15mm. It can be used with a heating block that supports thermocouples. Temperature measurement: -50°C~+350°C, which can replace the original K-type thermocouple temperature, very suitable for printing high temperature filaments. Use stainless steel with internal temperature kit to ensure the longest service life through accurate temperature measurement. For the convenience of customers, the wires are connected by lines, and customers can tear the wires according to their own applications. Material:stainless steel colour:white Package Contents: 5 * HT-NTC100K thermistorOnly the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

<div><p>Suggested ParametersR25=100K B25/50=3950K(±1%) Resistance Accuracy±1%±2%,±3% Temperature Range-40+300 B Accuracy±1% Max Rated Power45mW Package Include : 5/10 pcs Thermistors cables Resistance Temperature Coefficient-2-5%/</p><

✍H✔Y Creality 3D NTC 3950 100K Ohm Thermistor Sensor with 0.7 Meter Wiring Cale and Female Pin Head for Ender-3 3D Printer Heatbed Hot End Replacement Part Features: This NTC 3950 100K Ohm Thermistor for Ender-3 or other compatible 3D printers heat bed & extruder. 100K ohm temperature sensor. With female pin head for connecting easily. Comes with 0.7m high temperature insulated wire. Made of high-quality material, not easy to break and long durability. Specifications: Resistance: at 25°C=100K ohm Cable Length: Approx. 0.7m Package Size: 13 * 9 * 1cm / 5.1 * 3.5 * 0.4in Package Weight: 8.6g / 0.3oz Package List: 1 * Therm

Specifications: Negative Temperature Coefficient (NTC) Thermistor Model: B3950 Temperature measurement head size: 3 * 15mm 1. Upgrade from the original ordinary temperature probe directly exposed temperature measurement to resistance package temperature measurement. Temperature measurement head cylinder diameter 3mm, length 15mm, can be used with the heating block that support the thermocouple. &nbsp; 2. The temperature measurement range is increased from -50 ℃~ +250℃ to -50 ℃ ~ +350 ℃. It helps a lot to print high-temperature filament, can replace the original K-type thermocouple temperature. If need to print high-temperature filament, the HT-NTC100K thermistors are highly recommended. 3. The new version of HT-NTC100K temperature measuring thermistor adopts 304 stainless steel, with the internal temperature package to ensure the maximum service life with precision temperature measurement. &nbsp; 4. HT-NTC100K thermistor adopts white high-temperature cord, can bear higher temperature. And for customers' convenience, the wires adopts line connection, the customer can tear the wires depends on their application. The high temperature line is double thicker than others in the market, not easy to break off. &nbsp; 5. Supports the customization of different specifications, including the temperature head cylinder size, length of the wires (MOQ is 100 sets). &nbsp; 6. Can be used with the new version of the heater (the new heater can heat up to 350 degrees). Package included

Specifications: Negative Temperature Coefficient (NTC) Thermistor Model: B3950 Temperature measurement head size: 3 * 15mm -Upgrade from the original ordinary temperature probe directly exposed temperature measurement to resistance package temperature measurement. Temperature measurement head cylinder diameter 3mm, length 15mm, can be used with the heating block that support the thermocouple. &nbsp; -The temperature measurement range is increased from -50 °C~ +250°C to -50 °C ~ +350 °C. It helps a lot to print high-temperature filament, can replace the original K-type thermocouple temperature. If need to print high-temperature filament, the HT-NTC100K thermistors are highly recommended. -The new version of HT-NTC100K temperature measuring thermistor adopts 304 stainless steel, with the internal temperature package to ensure the maximum service life with precision temperature measurement. &nbsp; -HT-NTC100K thermistor adopts white high-temperature cord, can bear higher temperature. And for customers' convenience, the wires adopts line connection, the customer can tear the wires depends on their application. The high temperature line is double thicker than others in the market, not easy to break off. &nbsp; -Supports the customization of different specifications, including the temperature head cylinder size, length of the wires (MOQ is 100 sets). &nbsp; -Can be used with the new version of the heater (the new heater can heat up to 350 degrees). Package included

1. The Ender 3 ABL set is only applicable to the complete automatic bed leveling set of the Ender 3 Ender 3 PRO 3D printer. 2. Suitable for all printing surfaces, glass, aluminum substrates and removable architectural surfaces. 3. Complete and easy to write firmware and installation instructions, with all required software and compiled binary .hex files. 4. Capacitive sensor can be used on any printing surface 5. The custom shell can place pre-wired electronic devices Our sensor is optically isolated, so in case of failure, you will not have the risk of burning the printer motherboard, which is different from the diode or resistor setting. The sensor has been connected to the optical isolation ule, you only need to connect 2 wires and replace the Z-min connector. Including an icsp programmer for burning firmware. U disk content: firmware, burning software, installation and use instructions, drivers, etc. Our sensor is photoelectrically isolated. Therefore, unlike the diode or resistor setting, you don't have to risk burning the printer motherboard when a failure occurs. specification: Product name: Hot bed automatic leveling sensor kit Function: automatic leveling Applicable els: for Ender-3 Ender-3 PRO Colour: as shown Material: ABS+metal Package Contents: 1 set x hot bed automatic leveling sensor kitOnly the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

Specifications: Negative Temperature Coefficient (NTC) Thermistor Model: B3950 Temperature measurement head size: 3 * 15mm 1. Upgrade from the original ordinary temperature probe directly exposed temperature measurement to resistance package temperature measurement. Temperature measurement head cylinder diameter 3mm, length 15mm, can be used with the heating block that support the thermocouple. &nbsp; 2. The temperature measurement range is increased from -50 ℃~ +250℃ to -50 ℃ ~ +350 ℃. It helps a lot to print high-temperature filament, can replace the original K-type thermocouple temperature. If need to print high-temperature filament, the HT-NTC100K thermistors are highly recommended. 3. The new version of HT-NTC100K temperature measuring thermistor adopts 304 stainless steel, with the internal temperature package to ensure the maximum service life with precision temperature measurement. &nbsp; 4. HT-NTC100K thermistor adopts white high-temperature cord, can bear higher temperature. And for customers' convenience, the wires adopts line connection, the customer can tear the wires depends on their application. The high temperature line is double thicker than others in the market, not easy to break off. &nbsp; 5. Supports the customization of different specifications, including the temperature head cylinder size, length of the wires (MOQ is 100 sets). &nbsp; 6. Can be used with the new version of the heater (the new heater can heat up to 350 degrees). Package included

Specifications: Negative Temperature Coefficient (NTC) Thermistor Model: B3950 Temperature measurement head size: 3 * 15mm 1. Upgrade from the original ordinary temperature probe directly exposed temperature measurement to resistance package temperature measurement. Temperature measurement head cylinder diameter 3mm, length 15mm, can be used with the heating block that support the thermocouple. &nbsp; 2. The temperature measurement range is increased from -50 ℃~ +250℃ to -50 ℃ ~ +350 ℃. It helps a lot to print high-temperature filament, can replace the original K-type thermocouple temperature. If need to print high-temperature filament, the HT-NTC100K thermistors are highly recommended. 3. The new version of HT-NTC100K temperature measuring thermistor adopts 304 stainless steel, with the internal temperature package to ensure the maximum service life with precision temperature measurement. &nbsp; 4. HT-NTC100K thermistor adopts white high-temperature cord, can bear higher temperature. And for customers' convenience, the wires adopts line connection, the customer can tear the wires depends on their application. The high temperature line is double thicker than others in the market, not easy to break off. &nbsp; 5. Supports the customization of different specifications, including the temperature head cylinder size, length of the wires (MOQ is 100 sets). &nbsp; 6. Can be used with the new version of the heater (the new heater can heat up to 350 degrees). Package included

Descriptions: PT1000 sensors are able to measure higher temperatures than thermistors, and are more accurate then both thermistors and thermocouples in general. PT1000 sensors can direct replace the thermistors in your 3D printer  without adding an amplifier board like PT100's sensors. The PT1000 sensor is made of nylon material, durable, high temperature resistance, and its length is about 1m. But whith the default 4.7K pullup resister on board you will get lower resolution than other sensors. PT1000 sensors are compatible with most firmwares in the field. If you want release potential abilities of the PT1000 sensors, you need to replace the 4.7Kpullup resister of the thermistor pins with a 1K 0.1% resister. Specifications: Material: nylon Color: black Length: about 100cm End thickness: about 0.3cm Temperature: 500 Package included: 1pc x PT1000 thermistor sensor Note: 1. Due to the light difference, the item's color may be slightly different from the pictures. 2. Please allow 0.5-2 cm differences due to manual measurement. #Thermistor #Sensor #PT1000 #High #Temperature #3D #Printer #Part #Nylon #Waterproof #Accessories #Replacement #Cable #Por

set2: 1 x copper heating block + 1 x Sensor ule 1.Place the IR-sensor on the top of the Extruder-body and secure it with the M2x8. 2.Tighten the M2x8 screw, the sensor shouldn't be able to move, but be careful the PCB isn't indestructible ;) 3.Connect the cable, mind the correct orientation of the connector and wires. 4.Leave a slack behind the sensor like in the picture. Don't create too big loop as it might interfere with the frame. If needed adjust the length by gently pulling/pushing the cable. Item Type: Heated Block el Number: copper heater block The new sensor is using the optical sensor which is triggered by a simple mechanical lever. This sensor doesn't care about the optical properties of the filament (it can be completely invisible) and cannot die because of mechanical wear. How to match: 1 A2 Hardened Steel V6 Nozzles,click here 2 high quality V6 titanium alloy heat break TC4,click here 3 Thermistor Cartridge 350 degrees,click here 4 Thermistor Cartridge pt1000,click here colour:copper/Black Material:copper/metal + plastic copper heating block size:22MM x 16MM x 11.5mm Package Contents: 1 x copper heating block 1 x Sensor uleOnly the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

Specifications: Negative Temperature Coefficient (NTC) Thermistor Model: B3950 Temperature measurement head size: 3 * 15mm 1. Upgrade from the original ordinary temperature probe directly exposed temperature measurement to resistance package temperature measurement. Temperature measurement head cylinder diameter 3mm, length 15mm, can be used with the heating block that support the thermocouple. &nbsp; 2. The temperature measurement range is increased from -50 ℃~ +250℃ to -50 ℃ ~ +350 ℃. It helps a lot to print high-temperature filament, can replace the original K-type thermocouple temperature. If need to print high-temperature filament, the HT-NTC100K thermistors are highly recommended. 3. The new version of HT-NTC100K temperature measuring thermistor adopts 304 stainless steel, with the internal temperature package to ensure the maximum service life with precision temperature measurement. &nbsp; 4. HT-NTC100K thermistor adopts white high-temperature cord, can bear higher temperature. And for customers' convenience, the wires adopts line connection, the customer can tear the wires depends on their application. The high temperature line is double thicker than others in the market, not easy to break off. &nbsp; 5. Supports the customization of different specifications, including the temperature head cylinder size, length of the wires (MOQ is 100 sets). &nbsp; 6. Can be used with the new version of the heater (the new heater can heat up to 350 degrees). Package included

Detachable design, easy to install. XH2.54 and DuPont connectors are convenient for heating bed or hot extruder. Temperature sensor 100K ohm accuracy +/- 1%, total length: 1 meter Suitable for Creality CR-10S Pro, CR-X, Ender 3, Ender 3X, Ender-3 Pro, Prusa I3, Anet E10, etc. Colour: black + white Material: plastic Package Contents: 5 x NTC100K thermistor 5 x XH2.54 connector 5 x DuPont connectorOnly the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

Specifications: Negative Temperature Coefficient (NTC) Thermistor Model: B3950 Temperature measurement head size: 3 * 15mm 1. Upgrade from the original ordinary temperature probe directly exposed temperature measurement to resistance package temperature measurement. Temperature measurement head cylinder diameter 3mm, length 15mm, can be used with the heating block that support the thermocouple. &nbsp; 2. The temperature measurement range is increased from -50 ℃~ +250℃ to -50 ℃ ~ +350 ℃. It helps a lot to print high-temperature filament, can replace the original K-type thermocouple temperature. If need to print high-temperature filament, the HT-NTC100K thermistors are highly recommended. 3. The new version of HT-NTC100K temperature measuring thermistor adopts 304 stainless steel, with the internal temperature package to ensure the maximum service life with precision temperature measurement. &nbsp; 4. HT-NTC100K thermistor adopts white high-temperature cord, can bear higher temperature. And for customers' convenience, the wires adopts line connection, the customer can tear the wires depends on their application. The high temperature line is double thicker than others in the market, not easy to break off. &nbsp; 5. Supports the customization of different specifications, including the temperature head cylinder size, length of the wires (MOQ is 100 sets). &nbsp; 6. Can be used with the new version of the heater (the new heater can heat up to 350 degrees). Package included

set2: 1 x copper heating block + 1 x Sensor ule 1.Place the IR-sensor on the top of the Extruder-body and secure it with the M2x8. 2.Tighten the M2x8 screw, the sensor shouldn't be able to move, but be careful the PCB isn't indestructible ;) 3.Connect the cable, mind the correct orientation of the connector and wires. 4.Leave a slack behind the sensor like in the picture. Don't create too big loop as it might interfere with the frame. If needed adjust the length by gently pulling/pushing the cable. Item Type: Heated Block el Number: copper heater block The new sensor is using the optical sensor which is triggered by a simple mechanical lever. This sensor doesn't care about the optical properties of the filament (it can be completely invisible) and cannot die because of mechanical wear. How to match: 1 A2 Hardened Steel V6 Nozzles,click here 2 high quality V6 titanium alloy heat break TC4,click here 3 Thermistor Cartridge 350 degrees,click here 4 Thermistor Cartridge pt1000,click here colour:copper/Black Material:copper/metal + plastic copper heating block size:22MM x 16MM x 11.5mm Package Contents: 1 x copper heating block 1 x Sensor uleOnly the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

Specifications: Negative Temperature Coefficient (NTC) Thermistor Model: B3950 Temperature measurement head size: 3 * 15mm 1. Upgrade from the original ordinary temperature probe directly exposed temperature measurement to resistance package temperature measurement. Temperature measurement head cylinder diameter 3mm, length 15mm, can be used with the heating block that support the thermocouple. &nbsp; 2. The temperature measurement range is increased from -50 ℃~ +250℃ to -50 ℃ ~ +350 ℃. It helps a lot to print high-temperature filament, can replace the original K-type thermocouple temperature. If need to print high-temperature filament, the HT-NTC100K thermistors are highly recommended. 3. The new version of HT-NTC100K temperature measuring thermistor adopts 304 stainless steel, with the internal temperature package to ensure the maximum service life with precision temperature measurement. &nbsp; 4. HT-NTC100K thermistor adopts white high-temperature cord, can bear higher temperature. And for customers' convenience, the wires adopts line connection, the customer can tear the wires depends on their application. The high temperature line is double thicker than others in the market, not easy to break off. &nbsp; 5. Supports the customization of different specifications, including the temperature head cylinder size, length of the wires (MOQ is 100 sets). &nbsp; 6. Can be used with the new version of the heater (the new heater can heat up to 350 degrees). Package included

Specifications: Negative Temperature Coefficient (NTC) Thermistor Model: B3950 Temperature measurement head size: 3 * 15mm 1. Upgrade from the original ordinary temperature probe directly exposed temperature measurement to resistance package temperature measurement. Temperature measurement head cylinder diameter 3mm, length 15mm, can be used with the heating block that support the thermocouple. &nbsp; 2. The temperature measurement range is increased from -50 ℃~ +250℃ to -50 ℃ ~ +350 ℃. It helps a lot to print high-temperature filament, can replace the original K-type thermocouple temperature. If need to print high-temperature filament, the HT-NTC100K thermistors are highly recommended. 3. The new version of HT-NTC100K temperature measuring thermistor adopts 304 stainless steel, with the internal temperature package to ensure the maximum service life with precision temperature measurement. &nbsp; 4. HT-NTC100K thermistor adopts white high-temperature cord, can bear higher temperature. And for customers' convenience, the wires adopts line connection, the customer can tear the wires depends on their application. The high temperature line is double thicker than others in the market, not easy to break off. &nbsp; 5. Supports the customization of different specifications, including the temperature head cylinder size, length of the wires (MOQ is 100 sets). &nbsp; 6. Can be used with the new version of the heater (the new heater can heat up to 350 degrees). Package included

Specifications: Negative Temperature Coefficient (NTC) Thermistor Model: B3950 Temperature measurement head size: 3 * 15mm 1. Upgrade from the original ordinary temperature probe directly exposed temperature measurement to resistance package temperature measurement. Temperature measurement head cylinder diameter 3mm, length 15mm, can be used with the heating block that support the thermocouple. &nbsp; 2. The temperature measurement range is increased from -50 ℃~ +250℃ to -50 ℃ ~ +350 ℃. It helps a lot to print high-temperature filament, can replace the original K-type thermocouple temperature. If need to print high-temperature filament, the HT-NTC100K thermistors are highly recommended. 3. The new version of HT-NTC100K temperature measuring thermistor adopts 304 stainless steel, with the internal temperature package to ensure the maximum service life with precision temperature measurement. &nbsp; 4. HT-NTC100K thermistor adopts white high-temperature cord, can bear higher temperature. And for customers' convenience, the wires adopts line connection, the customer can tear the wires depends on their application. The high temperature line is double thicker than others in the market, not easy to break off. &nbsp; 5. Supports the customization of different specifications, including the temperature head cylinder size, length of the wires (MOQ is 100 sets). &nbsp; 6. Can be used with the new version of the heater (the new heater can heat up to 350 degrees). Package included