Board raspberry

A power module specially designed for Raspberry Pi, which allows the use of Raspberry Pi in a mobile form · Battery capacity: 3800 mAH (maximum); Current Rating: 1.8A · Output voltage (without load): 5.1 V ± 0.1 V · Dual USB outputs, one for the Raspberry Pi, the other for the built-in LCD screen · Comes with mounting brackets, screws and nut, so you can stack the Raspberry Pi board in the module Technical details introduction The power module is designed for the Raspberry Pi 3 Model B especially, allowing the master board to work offline for up to 9 hours. It is not just the supply for Raspberry Pi; This board has 2 Type-One USB ports-one power supplies for the Raspberry Pi and the other for the LCD in-built display. The module integrates a Li-ion Battery charger IC, a power management chip chip. And it is developed in strict accordance with the size of the HAT Raspberry Pi international expansion board, using only simple copper brackets to install Raspberry Pi multi-layer boards. specifications: The capacity of the battery: 3800 mAH Maximum discharge current: 1.8A No-load output voltage: 5.1 V ± 0.1 V Standard load current / voltage: 1.0A / 5.0V Cut-off voltage to fully charge Li-ion battery: 4.18V-4.2V Size: 8.5*4.5/3.35"*1.77" Package 1 * Lithium Battery Expansion Board (with lithium battery) 4 * impasse of Copper 4 * Screw 4

Raspberry Pi 3 model B Box case shell generation B+ acrylic shell latest box + 3 heat sinks Description Use An entire housing is made of six (3mm thick) transparent acrylic panels, each with a different wiring opening and buckle bit. 2 Case relatively light weight, in order to save freight and transportation security, the use of removable pack, six into bubble bag. 3 side connection port can be left breathable vent cover there, you can open up, good heat dissipation. 4 Each plate comes with double-sided protective film before installation to

Hello everyone, we are Reland Tech, we are mainly engaged in electronic components, electronic tools, bakery products. Customers can contact us for more product information. If there is any dissatisfaction, you can leave us a comment. We will actively correct, of course, thank you for your sincere evalua

Raspberry Pi là một máy tính đơn board được thiết kế bởi hãng Raspberry Pi (UK), có nhiều phiên bản kể từ khi ra đời. Phiên bản mới nhất là Raspberry Pi 4 được hãng giới thiệu và chính thức cung cấp trên thị trường vào tháng 6/2019. Thông số kỹ thuật của Raspberry Pi 4 Model B: Broadcom BCM2711, Quad core Cortex-A72 (ARM v8) 64-bit SoC @ 1.5GHz Có 3 lựa chọn RAM: 1GB, 2GB hoặc 4GB LPDDR4-2400 SDRAM Wifi chuẩn 2.4 GHz và 5.0 GHz IEEE 802.11ac. Bluetooth 5.0, BLE Cổng mạng Gigabit Ethernet 2 cổng USB 3.0 và 2 cổng USB 2.0 Chuẩn 40 chân GPIO, tương thích với các phiên bản trước Hỗ trợ 2 cổng ra màn hình chuẩn Micro HDMI với độ phân giải lên tới 4K Cổng MIPI DSI Cổng MIPI CSI Cổng AV 4 chân H.265 (4kp60 decode), H264 (1080p60 decode, 1080p30 encode) OpenGL ES 3.0 graphics Khe cắm Micro-SD cho hệ điều hành và lưu trữ Nguồn điện DC 5V – 3A DC chuẩn USB-C 5V DC via GPIO header (minimum 3A*) Hỗ trợ Power over Ethernet (PoE) (yêu cầu có PoE HAT) Raspberry Pi 4 có hình dáng bên ngoài vẫn nhỏ bé như các phiên bản trước, tuy nhiên cấu trúc bo mạch thì đã thay đổi hoàn toàn. Vì vậy bạn không thể sử dụng vỏ case của các phiên bản trước đó cho phiên bản 4 này. Bên cạnh đó, hãng cũng có thông báo về việc phải sử dụng nguồn 5V – 3A trở lên cho bo mạch Raspberry Pi 4. Một số điểm nâng cấp của Raspberry Pi 4 Model B CPU mạnh hơn Hỗ trợ chuẩn USB 3.0. RAM DDR4 thay vì DDR2 như cũ. Cổng mạng Ethernet Gigabit Có 2 cổng ra màn hình với độ phân giải 4K. Nguồn điện yêu cầu 5V – 3A thay vì 5V 2.5A như cũ Bluetooth nâng cấp từ phiên bản 4.0 lên 5.0 #proe #RaspberryPi4 #pi4 www.pr

Description: Features: 100% brand new and high quality. Each order comes with a 40-pin ribbon cable and assembled T-Type GPIO expansion board. Specifically designed for Raspberry pi 3 B, for Raspberry pi 2 B, for Raspberry pi 1 B+, etc. Can break out all those tasty power, GPIO, I2C and SPI pins from the 40-pin header onto a solderless breadboard You can plug the 40-pin GPIO cable between the Pi computer and the T Type GPIO expansion board. This GPIO expansion board is in a fancy T-shape, which is not as compact, but is a little easier to read the labels. Specifications: Material: Plastic + Metal Color: shown as pictures GPIO Cable Size: Length: 21cm (8.27in) (Approx.) Width: 5cm (1.97in) (Approx.) Compatibility: for Raspberry Pi 2 / 3 B+ Quantity: 1 Set (other accessories demo in the picture is not included) Note: 1.Transition: 1cm=10mm=0.39inch 2.Please allow 0-1cm error due to manual measurement. pls make sure you do not mind before you bid. 3.Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you! Package includes: (No retail package) 1 X GPIO 40-Pin Rainbow Ribbon Cable 1 X GPIO Extension

Board IO mở rộng cho phép Raspberry Pi3/4 kết nối với các cảm biến dry-contact và điều khiển đèn, motor.. Kết nối với Raspberry Pi qua header 40 Pin. Đặt điểm: • 8 ngõ vào số dry-contact • Input protection • 4 ngõ ra số relay • Dòng tải relay 7A/30VDC, 7A/250VAC No. In/Out put Pin Number GPIO Number 1 Input 0 11 GPIO17 2 Input 1 13 GPIO27 3 Input 2 15 GPIO22 4 Input 3 29 GPIO05 5 Input 4 31 GPIO06 6 Input 5 32 GPIO12 7 Input 6 33 GPIO13 8 Input 7 35 GPIO19 9 Output 0 36 GPIO16 10 Output 1 37 GPIO26 11 Output 2 38 GPIO20 12 Output 3 40 GPI

_______ Cửa hàng Apill chào mừng ♤ ___________ ✔Ready Stock !! Mua ngay! ✔COD ✔ Kiểm tra chất lượng ✔ Giá tốt nhất ✔Brand mới 100% Vận chuyển trong 1 ngày ★ Bất ngờ cho bạn ★ Quà tặng miễn phí: Theo dõi cửa hàng ❤ Nhật Like Giống 5 mục: Vận chuyển ưu tiên Gửi cho tôi Ảnh chụp màn hình và tin nhắn theo đơn đặt hàng của bạn: "Quà tặng miễn phí" nếu không sẽ bỏ lỡ Tip (Mẹo: Chúng tôi sẽ dựa trên khách của bạn ở quốc gia của bạn để gửi phích cắm bộ chuyển đổi tương ứng) Các nhà bán lẻ bán buôn được hoan nghênh đàm phán kinh doanh lâu dài với chúng tôi! __________________ Thông tin sản phẩm❀ __________________ Features: 1.With DAC All-function PCM5122 chip and I2S Input, X920 DAC+ board is a perfect PiFi / DAC+ / HIFI / Full-HD audio expansion board for Raspberry Pi 3 Model B/ 2B / B+. 2.After using X920 board, User can coordinate with the broadcast system (such as Volumio, RuneAudio, OSMC, XMBC(Kodi), MOODE etc.) to set up your own HIFI player network. 3.X920 is available with RCA, 3.5mm phone jack output connectors and built in IR receiver (Vishay TSOP34838). 4.Full-HD audio: up to 24-bit/192kHz playback and Class leading audio (112db SNR, and -93db THD) function, Integrated hardware volume control with TI's LP5907 Ultralow-Noise voltage regulator for optimal audio performance. 5.Powered by Raspberry Pi, no external power requirements, Conforms to the Raspberry Pi hardware-attached-on-top (HAT) specification. Specification: Raspberry Pi I2S Input (LRCK - GPIO19, BCK - GPIO18, DATA - GPIO21, GND) Output Ports: 1 x 3.5mm phone jack, 2 x RCA connectors Analog audio output level: 2.0VRMS Resolution/Sampling Rate: upto 24bit / 192KHz (Raspberry Pi I2S) IR receiver: GPIO17, 38KHz Operating System: Moode Audio Player, OSMC, Openelec, Raspbian Jessie, Volumio, Pi Core Player, RuneAudio Support: Volumio, RuneAudio, OSMC, XMBC(Kodi), MOODE etc. Full-HD audio: up to 24-bit/192kHz playback Built in audiophile TI Burr Brown DAC (TI PCM5122) Class leading audio: 112db SNR, and -93db THD Integrated hardware volume control TI's LP5907 Ultralow-Noise voltage regulator for optimal audio performance Built in IR receiver :Vishay TSOP34838) Available with RCA and 3.5mm phone jack output connectors Powered by Raspberry Pi, no external power requirements Conforms to the Raspberry Pi hardware-attached-on-top (HAT) specification Access to GPIO pins on HAT   Packing List: 1 x Expansion Bo

RP2040 microcontroller chip designed by Raspberry Pi in the United Kingdom. Dual-core Arm Cortex M0+ processor, flexible clock running up to 133 MHz 264KB of SRAM, and 2MB of on-board Flash memory. Castellated ule allows soldering direct to carrier boards. USB 1.1 with device and host support Low-power sleep and dormant es.Drag-and-drop programming using mass storage over USB. 26 x multi-function GPIO pins. 2 x SPI, 2 x I2C, 2 x UART, 3 x 12-bit ADC, 16 x controllable PWM channels. Accurate clock and timer on-chip. Temperature sensor, Accelerated floating-point libraries on-chip, 8 x Programmable I/O (PIO) state machines for custom peripheral support size:51 x 21mm Material:plastic colour:green Package Contents: 1 x for Raspberry Pi Pico Board 3 x Pin 1 x USB cableOnly the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

We have many products in our warehouse, our warehouse is in Shenzhen . Genaral it need 1-2weeks arrive your hand. if you subimit order , we will handle in 1-3days.if you chat with us , we donot reply you, donot worry , we are try to handle your order.so pls donot cancel o

Specifications: Item: step-up board Size: 77*20mm Voltage: DC 5V, 6V, 9V, 12V It can use as a power band. Note: please use for #Step-up #Board #UPS #Raspberry #Pi #4 #In #1 #DC #5V #6V #9V #12V #18650 #Battery #Charging #Durable #Ele

1. Upgrade the DAC chip, adopt the more advanced pcm5122 chip of BB company (which has been acquired by TI company), adopt I2S interface, and adjust the volume and audio parameters through I2C interface; support 16 to 32-bit audio data format; distortion and dynamic are very ideal, support high 384khz sampling rate, dynamic range 112dB, distortion - 93dB. For soft up or down ramp and analog squelch with 120 dB squelch signal-to-noise ratio (SNR) running without popping. 2. Pcm5122 is also integrated with negative charge pump, and the output does not need DC isolation; 2.1 VRMs grounding center output; very good ability to suppress out of band noise. By supporting loads as low as 1K Ω, the pcm510xa can drive multiple parallel products. (that is, multiple amplifiers are used at the same time). 3. The output port adopts gold-plated RCV double terminals and gold-plated 3.5mm earphone holder 4. The isolated power supply is designed to isolate the for raspberry Pai power supply from the DAC part of the independent power supply, and the magnetic beads are used to share the ground without interference with each other, so as to get rid of the current sound 5. It can be used by directly inserting the expansion board without welding, and it adopts I2S interface to directly decode digital to analog, and non USB interface DAC e, 1. Add two-color led to provide status display, red light is DAC power indicator (power is normally on), and green light is DAC working status light (on when decoding, off when stopping or not working), so as to better understand the working condition of DAC 2. It is perfectly compatible with the official PI hat size of raspberry school. The PCB board adopts high gold plating process and arc wiring (high-end hifi DAC adopts arc-shaped wiring), so as to better ensure the signal impedance continuity and reduce signal reflection and refraction. 3. Good sound depends on the real materials. The analog audio part uses hifi grade high-end DAC's fever level resistor 4. Provide infrared receiver interface (use gpio26, users can disconnect jumper JP2 when they don't want to use infrared) color: blue Material: metal + glue Package Contents:1 x chip Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

Feature: 1. The extended IO port can be directly inserted into the female head through the bread line, which is easy to use and can realize your ideas quickly and easily. 2. The IO port has terminal output. When connecting an external module, you can tighten the ordinary wires on the terminals. 3. Custom female connectors and silicone pads will help support the prototype shield of the for Raspberry Pi. 4. The product is suitable for Raspberry Pi 4B/3B+/3B/2B. 5. The board is featured with stable performance and long service life. Specification: Item Type: Multifunctional expansion boardHole Distance: Approx. 2.54mm / 0.1in Number of Male Header Pins: 40 Male Header Pin Pitch: Approx. 2.54mm / 0.1inUse: Suitable for Raspberry Pi 4B/3B+/3B/2B.Size: Approx. 89 x 56mm / 3.5 x 2.2in Package List: 1 x Multifunctional Expansion Board 1 x Pin Header 1 x Pa

Material: Copper Photo Color for Raspberry Pi Zero W/Zero/ Raspberry Pi 3 Model B /4B with the cable for it. 5MP Omnivision 5647 Camera ModuleWhy choose Aokin Camera Module Board for Raspberry Pi? The module attaches to Raspberry Pi, by way of a 15 Pin Ribbon Cable, to the dedicated 15-pin MIPI Camera Serial Interface (CSI), which was designed especially for interfacing to cameras.The CSI bus is capable of extremely high data rates, and it exclusively carries pixel data to the BCM2835 processor. The board itself is tiny, at around 25mm x 20mm x 9mm, and weighs just over 3g, making it perfect for mobile or other applications where size and weight are important. The sensor itself has a native resolution of 5 megapixel, and has a fixed focus lens onboard. In terms of still images, the camera is capable of 2592 x 1944 pixel static images, and also supports 1080p @ 30fps, 720p @ 60fps and 640x480p 60/90 video recording. Specification and Application: Specification: Viewing angle: 72 degrees Sensor type : Omni Vision OV5647 5MP Still Picture Resolution: 2592 x 1944 Video: Supports 1080p @ 30fps, 720p @ 60fps and 640x480p 60/90 Recording 5-pin MIPI Camera Serial Interface - Plugs Directly into the Raspberry Pi Board Application: Cellular phones,PDAs,Toys Other battery-powered products Can be used in all Raspberry Pi platforms Package Contents: 1 x Camera Module Board 1 x 15cm cableOnly the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

#PCM5102 #Decoder #Board #DAC #I2S #Interface #Sound #Card #Format #Player #for #Raspberry #PCM5102 #Decoder #Board PCM5102 Decoder Board DAC I2S Interface Sound Card Format Player for Raspberry PCM5102 Decoder Board 100% brand new and high quality Features: Made of high quality material, solid, durable and good performance, stability and reliability. Digital voice frequency, it sounds really good, much better than the onboard analog audio. The stereo jack comes soldered onto the board already, which is line out. PHAT format board. Uses the PCM5102A DAC to work with the Raspberry Pi I2S interface Decoder board only, other accessories demo in the picture is not included! Specification: Material: PCB Board, Electronic Components Optional Type and Size: 102: app.3.3 x 1.7cm/1.26 x 0.67in; 102A: app.3.2 x 2.4cm/1.26 x 0.94in Color: Purple Quantity: 1 Set Note: No retail package. Please allow 0-1cm error due to manual measurement. pls make sure you do not mind before you bid. Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you! Package includes: 1 x Decoder Board 1 x Pin H

There's no stick， it'll be bought again， thank you. Connectivity： Location of connector： 90 degree vertical connector， hd makers mishap that. One side of the contact when connecting to the other side to the mishap Software use： 1. Pleasant sterilizers and mishaps-Persistence has been updated for camera.， please carry out a burner once a-get romantic. A-get the mishap. 2. Placement of mishap and mishaps-choosing the mileage.， start the camera drive in the merchant firmware， then reboot Use the command line to mishap makers, and mishra maker and merry mileage to operate the camera.， catching a snippet or image The catching of a piece of mare needs to be mayer How to broadcast the camera's data live over the web： By order （Merry millet mileage merchant mile merrily） Input data of the camera， direct redirection to network port to realize petrifier The following is a detailed description Parameters: Reduction in the number of people： 1/45m Aperture： 2.9 Focus gap： 3.29 Field of view angle： 72.4 degrees Roster Connections： 1. Soft line， 90 degree vertical connector， hd makers mishap that. When connecting, the contact side is directed towards the mishap. 2. Remove the protective film from the mosaic before use 3. Nakedness， pay attention to e injuries， beware of static electricity Software use： 1. Pleasant sterilizers and mishaps-Persistence has been updated for camera.， please carry out a burner once a-get romantic. A-get the mishap. 2. Placement of mishap and mishaps-choosing the mileage.， start the camera drive in the merchant firmware， then reboot Use the command line to mishap makers, and mishra maker and merry mileage to operate the camera.， catching a snippet or image The catching of a piece of mare needs to be

NB-IoT HAT for Raspberry Pi, Based on SIM7020E, B1/B3/B5/B8/B20/B28 Bands Applicable Region SIM7020E is mainly applicable in Europe, Asia, Africa, Australia. Please check the supported bands according to your local service provider when placing order. Overview This is an NB-IoT (NarrowBand-Internet of Things) HAT for Raspberry Pi, controlled via serial AT commands, supports communication protocols like LWM2M/COAP/MQTT, etc. Due to the advantages of low delay, low power, low cost, and wide coverage, it is the ideal choice for IoT applications such as intelligent instruments, asset tracking, remote monitoring, and so on. Features Raspberry Pi connectivity, compatible with any revision Supports communication protocols such as LWM2M/COAP/MQTT/TCP/UDP/HTTP/HTTPS, etc. Onboard USB interface, for power supply OR debugging Breakout UART control pins, to connect with host boards like Arduino/STM32 Onboard voltage translator, 3.3V by default, allows to be switched to 5V via onboard jumper SIM card slot, supports NB-IoT specific card 2x LED indicators, easy to monitor the working status Baudrate: 300bps~921600bps (115200bps by default) Control via AT commands (V.25TER, 3GPP TS 27.007, and SIMCOM AT Commands) Comes with development resources and manual (examples for Raspberry Pi/Arduino/STM32/Python) Communications Specifications Band FDD-LTE B1/B3/B5/B8/B20/B28 Data rate Uplink≤62.5Kbps Downlink≤26.15Kbps SMS Text mode and PDU mode (depends on the NB card) General Specifications Power supply: 5V Logic level: 5V/3.3V (3.3V by default) Overall current (idle mode): ~18mA Single module current (VBAT=3.3V): Idle mode: 5.6mA Sleep mode: 0.4mA PSM mode: 5uA eDRX mode: 70uA (eDRX=655.36s) Dimension: 30.5mm x 65.0mm #proe #Sim

We have many products in our warehouse, our warehouse is in Shenzhen . Genaral it need 1-2weeks arrive your hand. if you subimit order , we will handle in 1-3days.if you chat with us , we donot reply you, donot worry , we are try to handle your order.so pls donot cancel o

el Number: IMX219 Demo Board Type: ARM This is a camera ule (without driver PCB) compatible with the official Raspberry Pi Camera Board V2, with 8-megapixel IMX219 sensor and features 160 degree field of view. IMX219 8-megapixel sensor Camera specifications CMOS size : 1/4inch color:black Material: ABS Aperture (F) : 2.35 Focal Length : 3.15mm Angle of View (diagonal) : 160 degree (while the original V2 camera is only 62.2 degree) Distortion: Less than 14.3% Focusing Range: 20cm ~ infinity 3280 x2464 still picture resolution Support 1080p30, 720p60 and 640x480p90 video record Package Contents: 1 * IMX219 Camera uleOnly the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

We have many products in our warehouse, our warehouse is in Shenzhen . Genaral it need 1-2weeks arrive your hand. if you subimit order , we will handle in 1-3days.if you chat with us , we donot reply you, donot worry , we are try to handle your order.so pls donot cancel o

Introduction: The Raspberry Pi Zero W extends the Pi Zero family, the Pi Zero W has all the functionality of the original Pi Zero but with added connectivity, consisting of : 802.11 b/g/n wireless LAN Bluetooth 4.1 Bluetooth Low Energy (BLE) Like the Pi Zero, it also has : 1GHz, single-core CPU 512MB RAM Mini HDMI and USB On-The-Go ports Micro USB power HAT-compatible 40-pin header Composite video and reset headers CSI camera connector colour:green Material:plastic size: 7.5*6*4cm Package Contents: 1*Raspberry Pi Zero W Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

Introduction: This is raspberry Pi USB hub , and integrated USB to serial port function , suitable for raspberry pi 3 / 2 / B+ / Zero / Zero W. It will make you get rid of the trouble of lack of USB port on your raspberry pi , expecially for raspberry pi zero . Features: 4 USB expansion ports, compatible with USB2.0 / 1.1 transmission. USB to UART for Raspberry Pi for serial debugging Multiple indicators for easy access to power, USB to UART and USB expansion interface Operating voltage: 5V Product Size: 65mm × 30mm Fixed hole diameter: 3.0m color: blue Material: PCB Package Contents: 1 x USB Hub Extension Board ( not include raspberry pi ) 1 x Micro-USB Cable 1 x Micro-USB AdapterOnly the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

100% brand new and high quality Features: 1. Specially designed for Raspberry Pi Zero. 2. Serial-function(CP2104), voltmeter chip(MAX17040G), 1000mAh Li-ion Battery are integrated into power supply board. 3. Thimble installation method lead to consiseness appearance. 4. The actual test standby time is up to 6 hours. (Test condition: zero w turn on the network and print out the power parameters every other 2 seconds). Specification: Type: Raspberry Pi Zero UPS Power Board Charging Current: 400mA Output Voltage: 5V ±0.1V Output Current: 1.3A@5V (Without external adapter) 1.3A@5V (With external adapter) Measurement Error: ±2% Size: 3 x 7cm(1.18 x 2.76in) Quantity: 1 Pc Note: 1. Please allow 0-1cm error due to manual measurement. pls make sure you do not mind before you bid. 2. Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you! Package includes: 1 x Raspberry Pi Zero UPS Power Board(Battery and Raspberry Pi are not inclu

Introduction: The Raspberry Pi Zero W extends the Pi Zero family, the Pi Zero W has all the functionality of the original Pi Zero but with added connectivity, consisting of : 802.11 b/g/n wireless LAN Bluetooth 4.1 Bluetooth Low Energy (BLE) Like the Pi Zero, it also has : 1GHz, single-core CPU 512MB RAM Mini HDMI and USB On-The-Go ports Micro USB power HAT-compatible 40-pin header Composite video and reset headers CSI camera connector colour:green Material:plastic size: 7.5*6*4cm Package Contents: 1*Raspberry Pi Zero W Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

3.5 inch TFT LCD Display Screen with Touch Panel 320*480 for RPi1/RPi2/raspberry pi3 Board V3 3.5inch standard display, support HDMI input, refresh rate of 60FPS or more Physical resolution 480x320, configurable software resolution up to 1920x1080 Can be used as a raspberry display, with touch control (need to install the touch driver) Can be used as a computer monitor, TV box, PSP and other standard HDMI output device (no touch function) Compatible and can be inserted directly into all versions Raspberry motherboard (raspberry generation 1 generation B type and zero need to reprovision HDMI cable) Support HDMI audio output, backlight brightness can be adjusted 【Product parameters】 Size: 3.5 (inch) SKU: MPI3508 Resolution: 480 × 320 (dots) Touch: Resistive touch Dimensions: 85.5 * 60.6 (mm) Product weight (with packaging): 14

Hello everyone, we are Reland Tech, we are mainly engaged in electronic components, electronic tools, bakery products. Customers can contact us for more product information. If there is any dissatisfaction, you can leave us a comment. We will actively correct, of course, thank you for your sincere evalua

We have many products in our warehouse, our warehouse is in Shenzhen . Genaral it need 1-2weeks arrive your hand. if you subimit order , we will handle in 1-3days.if you chat with us , we donot reply you, donot worry , we are try to handle your order.so pls donot cancel o

Cốc sứ in hình -Raspberry Pi Board MS1892 Thiết kế in hình độc đáo,trang nhã, Loại cốc chất lượng cao an toàn cho sức khỏe Sản phẩm truyền cảm hứng và làm quà tặng độc đáo cho người thân Cốc cao cấp : Được làm từ loại men cao cấp ,chất lượng in sắc nét ,rất bền màu. 1. Đặc điểm sản phẩm : - Chất liệu : Sứ trắng, men trắng, bóng mượt. - Công dụng : In ảnh cá nhân, tạo bất ngờ, yêu cầu độ nét cao làm quà tặng. - In ảnh lên cốc được từ 2-3 ảnh. - Giá thành hợp lý cho chất lượng sản phẩm. - Quá trình để hoàn thành một sản phẩm được trau chuốt từ những khâu nhỏ nhất. - Là món quà tặng vô cùng thiết thực và ý nghĩa. Bạn cảm thấy việc uống nước thật chẳng có gì thú vị và chẳng có động lực gì? Tại sao lại không chọn cho mình một chiếc cốc in hình độc đáo có thể truyền cảm hứng tạo sự thú vị. Sản phẩm tiện dụng,bền và đẹp, có thể sử dụng trong gia đình hoặc làm quà tặng. Cốc sứ men trắng cao cấp, không chứa chì và cadmium, an toàn cho sức khỏe người sử dụng. Cốc sứ cao cấp của chúng tôi sẽ là cách yêu thích mới của bạn để uống đồ uống nóng. Hoàn hảo để thể hiện niềm đam mê của bạn và thể hiện cá tính của bạn. Liên hệ: 0988960687 #cốcsứinhìnhtheoyêucầu #lysứinhìnhtheoyêucầu #lysứinhìnhtphcm #cốcsứcóhình #cốcsứhìnhảnh #đặtlysứinhình #lysứhìnhdoremon #lysứhìnhthú #lysứhìnhmèo #lysứhình12congiáp #inhìnhcốcsứ #cốcsứintên #lysứbiếnhìnhcảmứngnhiệt #bộcốcsứ #bộcốcsứcaocấp #incốcsứ #cốcsứinlogo #muacốcsứ """") Liên hệ 09889

Introduction: The Raspberry Pi Zero W extends the Pi Zero family, the Pi Zero W has all the functionality of the original Pi Zero but with added connectivity, consisting of : 802.11 b/g/n wireless LAN Bluetooth 4.1 Bluetooth Low Energy (BLE) Like the Pi Zero, it also has : 1GHz, single-core CPU 512MB RAM Mini HDMI and USB On-The-Go ports Micro USB power HAT-compatible 40-pin header Composite video and reset headers CSI camera connector colour:green Material:plastic size: 7.5*6*4cm Package Contents: 1*Raspberry Pi Zero W Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

#NESPi #CASE+ #Plus #For #Raspberry #Pi #1/2/3 #Model #B+ #Retroflag #HDMI #+ #Fan #+ #Case NESPi CASE+ Plus For Raspberry Pi 1/2/3 Model B+ Retroflag HDMI + Fan + Case Description New and improved NESPi Case+ Plus version with Safe Shutdown and Safe Reset function. It will be more safe for your SD card during shutdown and reset. This is a NES inspired enclosure for your Raspberry Pi system. It can turn your bare Raspberry Pi PCB into an elaborate console in an instant. Compatible with Raspberry PI 3 Model B, B+, Raspberry PI 2 Model B, Raspberry PI 1 Model B+ NES Style - This Pi case was created applying the most iconic element in the retro game world as a homage to the most classic console ever made. *POWER button, RESET button and LED all functional Front loading cartridge cover - Behind the small, hinged door, there are two USB ports and one standard RJ-45 connector. Improved HDMI and Audio ports - This is done to enhance the experience of using your HDMI and audio out-put cables. Micro SD card slot on the side - We put the slot for your Micro SD card on the side to allow more space for you to operate more freely. Customization - We tailored made this enclosure to fit in your Raspberry Pi PCB perfectly so that you can use it like a NES console as how you remember it. Includes NESPi Plus Case Adaptable PCB x 4 Screw driver x 1 Instruction manua

Specifications: With HDMI-compatible, earphone, SD card, Ethernet interfaces. Fits for Tinker Board S or for Raspberry development board. Aluminum case, very durable, and easy to install. Type: Case for Tinker Board Material: Aluminum Features: Fanless, Durable, Easy Install Size: 92mm x 68mm x 34mm/3.62" x 2.68" x 1.34" (Approx.) Notes: Due to the light and screen setting difference, the items color may be slightly different from the pictures. Please allow slight dimension difference due to different manual measurement. Package Includes: 1 x Case for Tinker