Arduino drv8825

Các tính năng: 1. Sử dụng các trình điều khiển stepper tương thích A4988 hoặc DRV8825. 2. Bảng mở rộng có thể được sử dụng cho máy khắc, bảng điều khiển máy in 3 d 3. Tương thích GRBL 0.8. ( PWM) và trục điều khiển, hỗ trợ 4 trục (X, Y, Z, A-Có thể lặp lại X, Y, Z hoặc do Một trục 4 đầy đủ với phần mềm tùy chỉnh sử dụng chân D12 và D13) 5. Thiết kế nhỏ gọn. Stepper Motors có thể được kết nối với 4 pin molex kết nối hoặc hàn tại chỗ. - DRV8825 Stepper Motor Driver Môđun có một pinout giao diện gần như giống với ổ cứng động cơ bước A4988, để nó có thể được sử dụng như là một hiệu suất cao hơn trong một trình đơn kéo xuống các tấm thay thế trong nhiều ứng dụng. DRV8825 có tính năng điều chỉnh giới hạn hiện tại, quá dòng và bảo vệ quá nhiệt, 6 độ phân giải (xuống 1/32 bước). Nó sử dụng 8,2 - 45 V, có thể cung cấp lên đến khoảng 1,5 cho mỗi giai đoạn không có tản nhiệt hoặc luồng không khí bắt buộc (được đánh giá lên đến 2,2 trên một khối lượng đủ làm mát thêm). Các tính năng: Giao diện điều khiển bước và bước đơn giản Giao diện có thể kết nối trực tiếp với các hệ thống 3.3V và 5V Hỗ trợ quá nhiệt tắt máy, ----------------------- HOTLINE: 024.2021.4848 ZALO : 0987.988.041 Địa chỉ mua hàng tại Hà Nội: 26- Ngõ 106- Lê Thanh Nghị- Hai Bà Trưng- Hà Nội ----------------------- Linh Kiện Điện Tử 3M cam kết: Bán giá luôn cạnh tranh và dịch vụ sau mua tốt nhất thị trường. Cam kết hoàn tiền 100% khi sản phẩm sai quảng cáo,hoặc lỗi do nhà sản xuất. Cam kết Sản Phẩm giốn

Hello everyone, we are Reland Tech, we are mainly engaged in electronic components, electronic tools, bakery products. Customers can contact us for more product information. If there is any dissatisfaction, you can leave us a comment. We will actively correct, of course, thank you for your sincere evalua

Uses removable A4988 or DRV8825 compatible stepper drivers. The extension board can be used for carving machine, 3 d printer driver expansion board GRBL 0.8 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals) PWM Spindle and direction pins,4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13) Compact design. Stepper Motors can be connected with 4 pin molex connectors or soldered in place. Voltage: DC 12~36 V Please note that this is an unassembled kit and Basic soldering skills are needed. DRV8825 Stepper Motor Driver The module has an interface pinout is almost the same with A4988 stepper motor drive carrier, so that it can be used as a higher performance in a pull-down menu the plates replaced in many applications. Features: Simple step and direction control interface The interface can connect directly with 3.3V and 5V systems Support over-temperature thermal shutdown, over-current shutdown and under-voltage lockout Support short-to-ground and shorted-load protection Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step 4-layer, 2 oz copper PCB for improved heat dissipation Adjustable current control support you to set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor's rated voltage to achieve higher step rates Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay) 45V maximum supply voltage Built-in regulator (needed external logic voltage supply) Colour:Color as shown Material:PCB board Package Contents: 1x CNC shielding plates 4x DRV8825 stepper motor driverOnly the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

We have many products in our warehouse, our warehouse is in Shenzhen . Genaral it need 1-2weeks arrive your hand. if you subimit order , we will handle in 1-3days.if you chat with us , we donot reply you, donot worry , we are try to handle your order.so pls donot cancel o

On-board DIP switch, you can easily adjust the drive segments. Terminal power connector for easy connection of drive power. Compatible with 12/24V drive scheme. Highly integrated expansion board, small size, stable performance. Suitable for 42 stepper motor drive, 3D printers and DIY. Logic voltage:5V Input voltage:12-30V Ports:Digital Interface:Direction, enable, speed Size:42*42*10mm Applicable ule:A4988, DRV8825 Motor Type:DC Motor colour:black material:PC + Metal Package Contents: 1 * Stepper Motor Driver Expansion BoardOnly the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

CNC shield V3 là board mở rộng của Arduino UNO R3 dùng để điều khiển các máy CNC mini.- Board có 4 khay dùng để cắm các mô đun điều khiển động cơ bước A4988,khi đó board có thể điều khiển3 trục X, Y, Z và thêm một trục thứ 4 tùy chọn trên các máy CNC mini. Sử dụng các trình điều khiển stepper tương thích A4988 hoặc DRV8825. Bảng mở rộng có thể được sử dụng cho máy khắc, bảng điều khiển máy in 3D. Tương thích GRBL 0.8. ( PWM) và trục điều khiển, hỗ trợ 4 trục (X, Y, Z, A-Có thể lặp lại X, Y, Z hoặc do Một trục 4 đầy đủ với phần mềm tùy chỉnh sử dụng chân D12 và D13). Thiết kế nhỏ gọn. Stepper Motors có thể được kết nối với 4 pin molex kết nối hoặc hàn tại chỗ. Thông Số Kỹ Thuật: Tương thích GRBL (mã nguồn mở chạy trên Arduino UNO R3 để điều khiển CNC mini) Hỗ trợ lên tới 4 trục (trục X, Y, Z và một trục thứ tư tùy chọn) Hỗ trợ tới 2 Endstop (cảm biến đầu cuối) cho mỗi trục Tính năng điều khiển spindle Tính năng điều khiển dung dịch làm mát khi máy hoạt động Sử dụng các mô đun điều khiển động cơ bước, giúp tiết kiệm chi phí khi thay thế, nâng cấp Thiết lập độ phân giải bước động cơ bằng jump đơn giản Thiết kế nhỏ gọn, các đầu nối tiêu chuẩn thông dụng Điện áp nguồn cấp đa dạng từ 12V tới 36V. Kích thước 6.8x5.4cm. Môđun có một pinout giao diện gần như giống với ổ cứng động cơ bước A4988, để nó có thể được sử dụng như là một hiệu suất cao hơn trong một trình đơn kéo xuống các tấm thay thế trong nhiều ứng dụng. DRV8825 có tính năng điều chỉnh giới hạn hiện tại, quá dòng và bảo vệ quá nhiệt, 6 độ phân giải (xuống 1/32 bước). Nó sử dụng 8,2 - 45 V, có thể cung cấp lên đến khoảng 1,5 cho mỗi giai đoạn không có tản nhiệt hoặc luồng không khí bắt buộc (được đánh giá lên đến 2,2 trên một khối lượng đủ làm mát thêm). Các tính năng: Giao diện điều khiển bước và bước đơn giản Giao diện có thể kết nối trực tiếp với các hệ thống 3.3V và 5V Hỗ trợ quá nhiệt tắt máy, ------------------------------------------- OneShop -Kênh Bán Buôn Linh Kiện Điện Tử - Đảm bảo luôn đủ hàng hóa với số lượng lớn để cung cấp cho anh em - Đảm bảo bao giá tốt nhất toàn thị trường - Đảm bảo sản phẩm được bảo hành và đổi trả miễn phí trong 7 ngày nếu Khách không hài lòng - Đảm bảo hoàn tiền 100% khi sản phẩm sai quảng cáo, hoặc lỗi do nhà sản xuất. - Đảm bảo sảm phẩm giống hình Thông Tin Hỗ Trợ - Vấn đề đơn hàng: 024.2021.4848 - Vấn đề hàng hóa: 024.6658.4141 - Vấn đề kĩ thuật: 0969.47

On-board DIP switch, you can easily adjust the drive segments. Terminal power connector for easy connection of drive power. Compatible with 12/24V drive scheme. Highly integrated expansion board, small size, stable performance. Suitable for 42 stepper motor drive, 3D printers and DIY. Logic voltage:5V Input voltage:12-30V Ports:Digital Interface:Direction, enable, speed Size:42*42*10mm Applicable module:A4988, DRV8825 Motor Type:DC Motor colour:black material:PC + Metal Package Contents: 1 * Stepper Motor Driver Expansion BoardOnly the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

Uses removable A4988 or DRV8825 compatible stepper drivers. The extension board can be used for carving machine, 3 d printer driver expansion board GRBL 0.8 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals) PWM Spindle and direction pins,4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13) Compact design. Stepper Motors can be connected with 4 pin molex connectors or soldered in place. Voltage: DC 12~36 V Please note that this is an unassembled kit and Basic soldering skills are needed. DRV8825 Stepper Motor Driver The module has an interface pinout is almost the same with A4988 stepper motor drive carrier, so that it can be used as a higher performance in a pull-down menu the plates replaced in many applications. Features: Simple step and direction control interface The interface can connect directly with 3.3V and 5V systems Support over-temperature thermal shutdown, over-current shutdown and under-voltage lockout Support short-to-ground and shorted-load protection Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step 4-layer, 2 oz copper PCB for improved heat dissipation Adjustable current control support you to set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor's rated voltage to achieve higher step rates Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay) 45V maximum supply voltage Built-in regulator (needed external logic voltage supply) Colour:Color as shown Material:PCB board Package Contents: 1x CNC shielding plates 4x DRV8825 stepper motor driverOnly the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

V3 (picture 2 & 3) =============== 0.9 compatible. Grbl (open source firmware that runs on an uno that turns the g-code commands into stepper 37signals) Pwm spindle and direction pins 4-axis support (x, y, z, a-can duplicate x, y z, or do a full 4th axis with custom firmware using pins d12 and d13) 2 x end stops for each axis (6 in total) Coolant enable. Uses removable a4988 or drv8825 compatible stepper drivers Some drivers like the drv8825 can do up to 1 / 32 micro-stepping Compact design. Stepper motors can be connected with a molex connector or soldered 4 in place pin. Runs on 12-36v dc. V4 (picture 1) ===================== Introduction 3d printer stepper motor driver cnc shield v4 needs to work with nano board. It can be used as driver expansion board for engraving machines and 3d printingers. It has in total 3 channel slots for a4988 stepper motor driver modules (not included) For driving 3 channel of stepper motors. Each channel of stepper motor only needs 2 io ports, Which means 6 io ports is sufficient to manage 3 stepper motors. This shield can make quick work for managing stepper motors in your project. Specification. 1. 3 axis stepper motor driver 2. Compatible with micro-drive laser engraving machine, three-axis cnc engraving machine, 3. 2a can be controlled within the two-phase four-wire stepper motor. 4. Released the digital io interface easy to connect to other modules such as endstop. 5. Released the i2c interface, you can connect to the lcd i2c or other i2c module. 6. Power dc5v interface, 7.5-12v voltage input. 7. Compatible grbl 8. Worked with

Feature: On-board DIP switch, you can easily adjust the drive segments Terminal power connector for easy connection drive power Compatible with 12 / 24V drive scheme Suitable for 42 stepper motor drive, 3D printers and DIY Specification: Size: 42 x 42 x 15mm Fixed: 3mm Pitch: 1400 x 1400mil (35.56 x 35.56mm) Logic voltage: 5V Input voltage: 12-30V Ports: Digital Interface: Direction, enable, speed Applicable module: A4988, DR

Uses removable A4988 or DRV8825 compatible stepper drivers. The extension board can be used for carving machine, 3 d printer driver expansion board. GRBL 0.8 compatible. (Open source firmware that runs on an For Arduino UNO that turns G-code commands into stepper signals) PWM Spindle and direction pins,4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13). Compact design. Stepper Motors can be connected with 4 pin molex connectors or soldered in place. Please note that this is an unassembled kit and Basic soldering skills are needed. DRV8825 Stepper Motor Driver. The ule has an interface pinout is almost the same with A4988 stepper motor drive carrier, so that it can be used as a higher performance in a pull-down menu the plates replaced in many applications. DRV8825 features an adjustable current limit, overcurrent and overtemperature protection, six micro-resolution (down 1/32-step). It uses 8.2 - 45V, can provide up to about 1.5 per phase no heat sink or forced air flow (rated up to 2.2 per volume sufficient additional cooling). Simple step and direction control interface. The interface can connect directly with 3.3V and 5V systems. Support over-temperature thermal shutdown, over-current shutdown and under-voltage lockout. Support short-to-ground and shorted-load protection. Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step. 4-layer, 2 copper PCB for improved heat dissipation. Adjustable current control support you to set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor's rated voltage to achieve higher step rates. Operating Temperature: other el Number: CNC Shield Board Condition: New Dissipation Power: other Supply Voltage: DC 12~36 V Type: Logic ICs Application: CNC Shield Board CNC Shield Board Version: 3.0 Intelligent chopping control that automatically selects the correct current decay e(fast decay or slow decay) 45V maximum supply voltage Built-in regulator (needed external logic voltage supply) Uno R3 Board MCU: ATmega328 Clock speed: 16 MHz USB interface: ATmega16U2 Operating voltage: 5 V I-I / O pin output current: 40 mA max 3.3 V output current: 150 mA max Digital I/O pins: 14 (including 6 with PWM capability) Analog input pins: 6 EEPROM: 1 kB Static RAM (SRAM): 2 kB Flash memory: 32 kB colour: Picture color Material: PC Size(L*W*H): 68 x 53 x 10 mm Package Contents: 1 x Uno R3 Board 1 x CNC Shield Board 4 x DRV8825 Stepper Motor Driver 4 x Heat Sink 1 x USB Cable 1 x 40-Pin Row Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

Simple step and direction control interface; The interface can connect directly with 3.3V and 5V systems; Support over-temperature thermal shutdown, over-current shutdown and under-voltage lockout; Support short-to-ground and shorted-load protection; Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step; 4-layer, 2 oz copper PCB for improved heat dissipation. Adjustable current control support you to set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor's rated voltage to achieve higher step rates; Intelligent chopping control that automatically selects the correct current decay e (fast decay or slow decay). Uses removable A4988 or DRV8825 compatible stepper drivers. The extension board can be used for carving machine, 3 d printer driver expansion board GRBL 0.8 compatible. (Open source firmware that runs on an for Arduino UNO that turns G-code commands into stepper signals) PWM Spindle and direction pins,4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13) Compact design. Stepper Motors can be connected with 4 pin molex connectors or soldered in place. Please note that this is an unassembled kit and Basic soldering skills are needed. DRV8825 Stepper Motor Driver The ule has an interface pinout is almost the same with A4988 stepper motor drive carrier, so that it can be used as a higher performance in a pull-down menu the plates replaced in many applications. DRV8825 features an adjustable current limit, overcurrent and overtemperature protection, six micro-resolution (down 1/32-step). It uses 8.2 - 45V, can provide up to about 1.5 per phase no heat sink or forced air flow (rated up to 2.2 per volume sufficient additional cooling). 45V maximum supply voltage Built-in regulator (needed external logic voltage supply) CNC Shield Board Version: 3.0 Voltage: DC 12~36 V Colour: As shown Material: PCB Size: 6.8x5.3x1.8cm Package Contents: 1 * v3 engraving machine expansion board 4 * DRV8825 drivers 4 * heat sinks Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

Uses removable A4988 or DRV8825 compatible stepper drivers. The extension board can be used for carving machine, 3 d printer driver expansion board. GRBL 0.8 compatible. (Open source firmware that runs on an For Arduino UNO that turns G-code commands into stepper signals) PWM Spindle and direction pins,4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13). Compact design. Stepper Motors can be connected with 4 pin molex connectors or soldered in place. Please note that this is an unassembled kit and Basic soldering skills are needed. DRV8825 Stepper Motor Driver. The ule has an interface pinout is almost the same with A4988 stepper motor drive carrier, so that it can be used as a higher performance in a pull-down menu the plates replaced in many applications. DRV8825 features an adjustable current limit, overcurrent and overtemperature protection, six micro-resolution (down 1/32-step). It uses 8.2 - 45V, can provide up to about 1.5 per phase no heat sink or forced air flow (rated up to 2.2 per volume sufficient additional cooling). Simple step and direction control interface. The interface can connect directly with 3.3V and 5V systems. Support over-temperature thermal shutdown, over-current shutdown and under-voltage lockout. Support short-to-ground and shorted-load protection. Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step. 4-layer, 2 copper PCB for improved heat dissipation. Adjustable current control support you to set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor's rated voltage to achieve higher step rates. Operating Temperature: other el Number: CNC Shield Board Condition: New Dissipation Power: other Supply Voltage: DC 12~36 V Type: Logic ICs Application: CNC Shield Board CNC Shield Board Version: 3.0 Intelligent chopping control that automatically selects the correct current decay e(fast decay or slow decay) 45V maximum supply voltage Built-in regulator (needed external logic voltage supply) Uno R3 Board MCU: ATmega328 Clock speed: 16 MHz USB interface: ATmega16U2 Operating voltage: 5 V I-I / O pin output current: 40 mA max 3.3 V output current: 150 mA max Digital I/O pins: 14 (including 6 with PWM capability) Analog input pins: 6 EEPROM: 1 kB Static RAM (SRAM): 2 kB Flash memory: 32 kB colour: Picture color Material: PC Size(L*W*H): 68 x 53 x 10 mm Package Contents: 1 x Uno R3 Board 1 x CNC Shield Board 4 x DRV8825 Stepper Motor Driver 4 x Heat Sink 1 x USB Cable 1 x 40-Pin Row Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

Simple step and direction control interface; The interface can connect directly with 3.3V and 5V systems; Support over-temperature thermal shutdown, over-current shutdown and under-voltage lockout; Support short-to-ground and shorted-load protection; Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step; 4-layer, 2 oz copper PCB for improved heat dissipation. Adjustable current control support you to set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor's rated voltage to achieve higher step rates; Intelligent chopping control that automatically selects the correct current decay e (fast decay or slow decay). Uses removable A4988 or DRV8825 compatible stepper drivers. The extension board can be used for carving machine, 3 d printer driver expansion board GRBL 0.8 compatible. (Open source firmware that runs on an for Arduino UNO that turns G-code commands into stepper signals) PWM Spindle and direction pins,4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13) Compact design. Stepper Motors can be connected with 4 pin molex connectors or soldered in place. Please note that this is an unassembled kit and Basic soldering skills are needed. DRV8825 Stepper Motor Driver The ule has an interface pinout is almost the same with A4988 stepper motor drive carrier, so that it can be used as a higher performance in a pull-down menu the plates replaced in many applications. DRV8825 features an adjustable current limit, overcurrent and overtemperature protection, six micro-resolution (down 1/32-step). It uses 8.2 - 45V, can provide up to about 1.5 per phase no heat sink or forced air flow (rated up to 2.2 per volume sufficient additional cooling). 45V maximum supply voltage Built-in regulator (needed external logic voltage supply) CNC Shield Board Version: 3.0 Voltage: DC 12~36 V Colour: As shown Material: PCB Size: 6.8x5.3x1.8cm Package Contents: 1 * v3 engraving machine expansion board 4 * DRV8825 drivers 4 * heat sinks Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

Simple step and direction control interface; The interface can connect directly with 3.3V and 5V systems; Support over-temperature thermal shutdown, over-current shutdown and under-voltage lockout; Support short-to-ground and shorted-load protection; Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step; 4-layer, 2 oz copper PCB for improved heat dissipation. Adjustable current control support you to set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor's rated voltage to achieve higher step rates; Intelligent chopping control that automatically selects the correct current decay e (fast decay or slow decay). Uses removable A4988 or DRV8825 compatible stepper drivers. The extension board can be used for carving machine, 3 d printer driver expansion board GRBL 0.8 compatible. (Open source firmware that runs on an for Arduino UNO that turns G-code commands into stepper signals) PWM Spindle and direction pins,4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13) Compact design. Stepper Motors can be connected with 4 pin molex connectors or soldered in place. Please note that this is an unassembled kit and Basic soldering skills are needed. DRV8825 Stepper Motor Driver The ule has an interface pinout is almost the same with A4988 stepper motor drive carrier, so that it can be used as a higher performance in a pull-down menu the plates replaced in many applications. DRV8825 features an adjustable current limit, overcurrent and overtemperature protection, six micro-resolution (down 1/32-step). It uses 8.2 - 45V, can provide up to about 1.5 per phase no heat sink or forced air flow (rated up to 2.2 per volume sufficient additional cooling). 45V maximum supply voltage Built-in regulator (needed external logic voltage supply) CNC Shield Board Version: 3.0 Voltage: DC 12~36 V Colour: As shown Material: PCB Size: 6.8x5.3x1.8cm Package Contents: 1 * v3 engraving machine expansion board 4 * DRV8825 drivers 4 * heat sinks Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

Stepper motor driver module description dvr8825 u 3d printer stepper 1. Maximum 2.5a current; 2. Highest support 32 segments; 3. 4 layers pcb board, better heat dissipation performance; 4. Smaller internal resistance chip, lower heating, better heat dissipation; Applicable occupations: Occupion that drive stepper motors are needed; Must modules to build 3d printers, cnc, engraving machine, etc.; Supported 3d printers: Prusa, mendel, ultimaker, printbot, makerbot, and so on. You can refer to the following arduino code to directly drive the motor; Features: 1. Suitable for driving 8.2v ~ 45v 2.5a stepper motors; 2. Only simple step and direction control interface; 3. Six different steps patterns: All, half, 4 / 1, 8 / 1, 16 / 1 / 32; 4. Adjustable potentiometer can adjust the maximum current output, so as to achieve higher step rate; 5. Automatic current attenuation mode detection / selection; 6. Overheating shutdown circuit, underwater lockout, cross current protection; 7. Earthing short circuit protection and loading short circuit protection Specifications: Stepper motor driver module drv8825 for 3d printer reprap 4 ramps1.4 stepstick Size: 15x20mm / 0.59x0.79 " Driving current: 2.5a. Segments: 2 / 1, 4 / 1, 8 / 1, 16 / 1, 32 / 1 Manufacturing process: Smt machine manufacturing, non manual welding, good quality, higher performance, more stable Including: 1 x stepper motor driver module drv8825 Sku-mcrl5

Các tính năng: 1. Sử dụng các trình điều khiển stepper tương thích A4988 hoặc DRV8825. 2. Bảng mở rộng có thể được sử dụng cho máy khắc, bảng điều khiển máy in 3 d 3. Tương thích GRBL 0.8. ( PWM) và trục điều khiển, hỗ trợ 4 trục (X, Y, Z, A-Có thể lặp lại X, Y, Z hoặc do Một trục 4 đầy đủ với phần mềm tùy chỉnh sử dụng chân D12 và D13) 5. Thiết kế nhỏ gọn. Stepper Motors có thể được kết nối với 4 pin molex kết nối hoặc hàn tại chỗ. - DRV8825 Stepper Motor Driver Môđun có một pinout giao diện gần như giống với ổ cứng động cơ bước A4988, để nó có thể được sử dụng như là một hiệu suất cao hơn trong một trình đơn kéo xuống các tấm thay thế trong nhiều ứng dụng. DRV8825 có tính năng điều chỉnh giới hạn hiện tại, quá dòng và bảo vệ quá nhiệt, 6 độ phân giải (xuống 1/32 bước). Nó sử dụng 8,2 - 45 V, có thể cung cấp lên đến khoảng 1,5 cho mỗi giai đoạn không có tản nhiệt hoặc luồng không khí bắt buộc (được đánh giá lên đến 2,2 trên một khối lượng đủ làm mát thêm). Các tính năng: Giao diện điều khiển bước và bước đơn giản Giao diện có thể kết nối trực tiếp với các hệ thống 3.3V và 5V Hỗ trợ quá nhiệt tắt máy, #MODUN #UNOR3 #SHIEL #stepermotors #arduino #linhkiendientu #linhkien #linhkien024 #linhkienlammach #lammachthucong Hotline: 09786

42 Stepper Motor Driver Expansion Board DRV8825 A4988 3D Printer Control Shield Module For Arduino UNO R3 Ramps1.4 DIY Kit One Features: 1. On-board DIP switch, you can easily adjust the drive segments 2. Terminal power connector for easy connection drive power 3. Compatible with 12 / 24V drive scheme 4. Suitable for 42 stepper motor drive, 3D printers and DIY Specifications: Size: 42 x 42 mm Fixed: 3mm Pitch: 1400 x 1400mil (35.56 x 35.56mm) Logic voltage: 5V Input voltage: 12-30V Ports: Digital Interface: Direction, enable, speed Applicable modul: A4988, DRV8825 Note: Please note the direction when installing the drive module, otherwise it will burn module Package includes: 1 x 42 Stepper Motor Drive Expansion

This product belongs to consumables. It's new, tested and delivered. There's no warranty. If there's a problem, it won't be returned, Take care if you mind! Be careful:A4988Green is the same as red 1AOf Functions and advantages low RDS(open)output Automatic current attenuation mode detection/Choice Mixed and slow current decay mode Synchronous rectification for low power dissipation #Motor #Driver inside UVLO Cross current protection 3.3 and 5 V Compatible logic power supply Thermal shutdown circuit Ground short circuit protection Load short circuit protection Five optional step modes: full 1/2,1/4,1/8 and 1/16 DRV8825Relative4988 Advantages: 1. maximum current2.5A。 2, top support32To subdivide. 3,4layerPCBBoard, better heat dissipation performance. 4The internal resistance of the chip is smaller, the heat is lower and the heat dissipation is better. Parameters: Size:1.5mmX2mm(and)4988Same) Driving current:2.5A To subdivide:1,1/2,1/4,1/8,1/16,1/32 Manufacturing process:SMTSMT machine manufacturing, non manual welding, higher yield, more stable performance Suitable for: Where stepper motors need to be driven. Is building3dPrinter,cnc, engraving machine and other necessary modules. Supportive3dPrinter hasPrusa Mendel,ultimaker,printbot,makerbotAnd so on. 1，Suitable for driving8.2V~45V 2.5AThe following stepper motors; 2， only simple step and direction control interface; 3，Six different step modes: full, half1/4,1/8,1/16,1/32; 4， the adjustable potentiometer can adjust the maximum current output to obtain a higher step rate; 5， automatic current attenuation mode detection/Choice; 6，Over temperature shutdown circuit, under voltage locking, cross current protection; 7，Grounding short circuit protection and loading short circuit protection Note: Due to manual measurement, please allow 1-3mm different. Due to different displays and different lighting, the image may not reflect the actual colors of the project. Thank you for your understanding. When purchasing electronic components, please have certain electronic basic knowledge of the module. Most modules only provide descriptions or send materials. There is no technical consulting support. Please be careful to shoot for begin

🍃 Stepper motor driver drv8825 drv 8825 stepstick 3d printer arduino 📣📣📣 Note: - and there are more practical modules. It 's perfect for those who want to learn. Product description Stepper motor driver drv8825 stepper stepper stepper Reprap 3d printer stepper motor driver drv8825 Max current: 2.5a. Up to 32 segments. - 4-layer pcb - chip resistance, so less heat, and better heat dissipation 📣📣📣 👩‍🦳️🎋 Read compulsory notes before transactions 👩‍🦳️🎋 Check stock before order 👩‍🦳️🎋 The products that have been purchased cannot be returned 👩‍🦳️🎋 Do not accept any return & complaint in any form 👩‍🦳️🎋 Stepper motor driver drv8825 drv 8825 stepstick 3d printer ar

Simple step and direction control interface; The interface can connect directly with 3.3V and 5V systems; Support over-temperature thermal shutdown, over-current shutdown and under-voltage lockout; Support short-to-ground and shorted-load protection; Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step; 4-layer, 2 oz copper PCB for improved heat dissipation. Adjustable current control support you to set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor's rated voltage to achieve higher step rates; Intelligent chopping control that automatically selects the correct current decay e (fast decay or slow decay). Uses removable A4988 or DRV8825 compatible stepper drivers. The extension board can be used for carving machine, 3 d printer driver expansion board GRBL 0.8 compatible. (Open source firmware that runs on an for Arduino UNO that turns G-code commands into stepper signals) PWM Spindle and direction pins,4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13) Compact design. Stepper Motors can be connected with 4 pin molex connectors or soldered in place. Please note that this is an unassembled kit and Basic soldering skills are needed. DRV8825 Stepper Motor Driver The ule has an interface pinout is almost the same with A4988 stepper motor drive carrier, so that it can be used as a higher performance in a pull-down menu the plates replaced in many applications. DRV8825 features an adjustable current limit, overcurrent and overtemperature protection, six micro-resolution (down 1/32-step). It uses 8.2 - 45V, can provide up to about 1.5 per phase no heat sink or forced air flow (rated up to 2.2 per volume sufficient additional cooling). 45V maximum supply voltage Built-in regulator (needed external logic voltage supply) CNC Shield Board Version: 3.0 Voltage: DC 12~36 V Colour: As shown Material: PCB Size: 6.8x5.3x1.8cm Package Contents: 1 * v3 engraving machine expansion board 4 * DRV8825 drivers 4 * heat sinks Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

Feature: On-board DIP switch, you can easily adjust the drive segments Terminal power connector for easy connection drive power Compatible with 12 / 24V drive scheme Suitable for 42 stepper motor drive, 3D printers and DIY Specification: Size: 42 x 42 x 15mm Fixed: 3mm Pitch: 1400 x 1400mil (35.56 x 35.56mm) Logic voltage: 5V Input voltage: 12-30V Ports: Digital Interface: Direction, enable, speed Applicable module: A4988, DRV8825 Note: Please note the direction when installing the drive module, otherwise it will burn module 1 PCS x 42 Stepper Motor Drive Expansion