Adruino360

Bộ Arduino Advanced Kit [Bộ Kit Arduino nâng cao] gồm: Một KIT Arduino Uno R3 và một số lượng lớn các Module cần thiết sẽ giúp bạn xây dựng các Dự án sáng tạo . Đặc biệt là các bạn mới tiếp xúc và làm quen với Arduino, muốn đi từ Cơ bản đến Nâng cao. TẠI SAO CHỌN BỘ ARDUINO NÂNG CAO? - Số lượng Module (Cảm biến) nhiều => Tiếp xúc nhiều loại Module - CODE MẪU TẶNG KÈM => Học nhanh + Hiệu Quả - Sử dụng Arduino Uno R3 chip cắm (Chip nạp ATMEGA16U2) - Với Bộ Advanced thực hành: UART, I2C, SPI, IN-OUT, ANALOG,... =>LƯU Ý: MODULE LCD+I2C (Một số bộ KIT thị trường chỉ LCD thường, không có I2C tích hợp, nên khó học về LCD); MODULE THỜI GIAN THỰC, TẶNG KÈM PIN Ad sẽ gửi tặng bạn bộ tài liệu ebook Adruino nâng cao (HƯỚNG DẪN + CODE MẪU) đi kèm sản phẩm. Bộ Arduino Advanced Kit bao gồm: - KIT ARDUINO UNO R3 – Chíp Cắm (chip nạp ATMEGA16U2)        1 - Cáp Nối UNO R3 (USB Cable)                 1 - LCD1602 Xanh Dương   (Kèm I2C)          1 - Động Cơ Servor SG90                              1 - Module ULN2003                                      1 - Động Cơ Bước 28BYJ-48                         1 - Kẹp pin 9v (Battery clip)                            1 - Triết áp đơn 10K (Potentiometer)             1 - Dây bẹ 2 đầu đực –cái                     10(sợi)  - Bó dây nối đực-đực                         30 (sợi) - Bo Test (Breadboard 16.5×5.5cm)           1 - Led Matrix 8×8                                         1 - Led 7 Thanh 4 Số (4×7 segment)            1 - Led 7 Thanh 1 Số (1×7 segment)            1 - Còi chip  (Buzzer )                                   2 - Vỏ Nút Nhấn B3F (tròn)                           4 - Nút Nhấn 4 Chân B3F (Switch)               4 - Cảm biến rung (SW-520D)                      2 - IC ghi dịch cho LED (IC 74HC595)          1 - Cảm biến lửa (Flame sensor)                  1 - Mắt Thu Hồng Ngoại (Infrared receiver)  1 - Remote Hồng Ngoại (21 phím)                1 - Cảm biến nhiệt độ (sensor LM35)           1 - Điện trở quang (Photoresistor)                3 - Điện trở 220R                                          10 - Điện trở 1K                                              10 - Điện trở 10K                                            10 - Led Đỏ (5mm)                                          10 - Led Xanh Lá (5mm)                                 10 - Led Vàng (5mm)                                      10 -Module điều khiển 2 chiều (Joystick)        1 - Module RGB (led 3 màu)                         1 - Module RFID RC522 13.56MHz              1 - Bàn Phím Ma Trận 4×4 V2                      1 - Module thời gian thực (DS1307) +PIN     1 - Module relay 5V                                       1 - Module cảm biến âm thanh                     1 - Module nhiệt độ, độ ẩm (DHT11)            1 - Module cảm biến mực nước                   1 - Hộp nhựa đựng bộ ARDUINO KIT          1 #arduino #arduinostarterkit #arduinonangcao #arduinocoban #bohoctaplaptrinhArduino #

TÊN SP: Module Arduino Uno R3 chíp dán ỨNG DỤNG: -Arduino Uno R3 được ứng dụng rất mạnh mẽ trong cả học tập và chế tạo sản phẩm, từ những thiết bị đơn giản đến phức tạp. -Ứng dung trong học tập : Điều khiển đèn LED nhấp nháy, xử lý tín hiệu cho xe điều khiển từ xa, làm một trạm đo nhiệt độ – độ ẩm và hiển thị lên màn hình LCD …. -Ứng dụng trong đời sống : Làm thiết bị nhà thông minh, khóa của tự động, làm sản phẩm nông nghiệp thông minh … -Ứng dụng trong công nghiệp : Hiện nay Arduino được sử dụng khá nhiều trong công nghiệp vì giá thành của nó khá tốt , độ ổn định cao. -Arduino Uno là board mạch rất phổ biến trong các dòng Arduino hiện nay, bạn chỉ cần kết nối -Arduino với máy tính PC hoặc Laptop bằng cáp USB là đã có thể sử dụng và nạp code cho nó một cách rất dễ dàng. Lưu ý : Điện áp khuyên dùng cho arduino khi cấp nguồn ngoài là từ 7-12v , không nên dùng với điện áp vao hơn có thể gây hư hỏng mạch THÔNG SỐ KỸ THUẬT: -Chip điều khiển : ATmega328P-AU -SRAM : 2 KB (ATmega328) -EEPROM : 1 KB (ATmega328) -Tốc độ : 16 MHz -Nguồn nuôi mạch : 5V từ cổng USB hoặc 7-9v từ giắc tròn DCIN -Số chân Digital : 14 chân -Số chân PWM : 6 chân -Số chân Analog : 6 chân -Dòng ra trên mỗi chân tối đa : 40mA -Dòng ra trên chân 3v3 tối đa : 150mA -Dung lượng bộ nhớ Flash : 32 KB – ATmega328 ( 0.5 KB sử dụng cho bootloader ) TÀI LIỆU: -Để nạp code cho board Arduino trước tiên chúng ta cần cài driver cho máy tính : tải driver CH340 tại đây. LINK https://drive.google.com/open?id=1VLFqPhzv--fim-4yDmWKwA59Jqr1BoMK -Sơ đồ ra chân của board arduino :(HÌNH 5) -Arduino.cc Đây là trang web chính thức của nhóm tác giả Arduino, nó chưa vô vàn kiến thức cho cả người mới bắt đầu và cả những dự án lớn nữa. Đây là trang web tiếng anh nên chúng ta có thể vào vừa học vừa tăng khả năng dịch tiếng anh nhé -Arduino.vn Cũng giống như Arduino.cc, trang web này chứa rất nhiều project lớn nhỏ do cộng đồng arduino việt nam phát triển, tất nhiên nó là tiếng việt nhé nên anh em vào lựa mấy dự án hay mà chiến thôi. -Phần mềm Arduino IDE : Phần mềm này có thể down tại Arduino.cc, mình đặt luôn link download tại đây cho ai ngại vào kia tìm nhé : Download tại đây. LINK https://www.arduino.cc/en/Main/Software #arduino #UnoR3 #Uno #arduino #SMD #lậptrình #laptrinh #module #machDien #mạchđiện #Module #Arduino #Uno #R3 #chíp

2 shots Arduino ky-040 Working voltage: 5v Pulse number: 20 The rotation encoder can count the number of pulses output in the process of positive and reverse rotation by rotating, rotational counts are not like potentiometers, this turn count is unlimited. Keys on the rotating encoder, can be reset to initial state, that is, count from zero. Working principles: Increment encoder is a rotary sensor that converts rotational displacement to a series of digital pulse signals. These pulses are used to control angular displacement. The principle of optoelectronic scanning is used for the conversion of angular displacement in eltra encoder. A reading system consists of a radial dial consisting of alternate transmission windows and opaque windows (Dockboard) Based on the rotation, also vertically irradiated by an infrared source, light project the image of the dockboard onto the receiver surface. The receiver is covered with a layer of diffraction grating, it has the same window width as the dock. The receiver 's work is to feel the change in disk rotation, the light change is then converted into corresponding electrical changes. Then raise the low-level signal to a higher level, and produces square pulses without any interference, this must be handled by electronic circuits. The reading system usually uses differential method, compare the different signals of two waveforms but with a phase difference of 180°, to improve the quality and stability of output signals. Readings are formed on the basis of differences between two more signals, this eliminates interfer

Welcome to Oorange.vn Features: Applies to model airplane / Model car / robot Torque: 5.5kg/cm (at 4.8V) Speed: 0.22sec/60°(at 4.8V) Working voltage: 4.8v-6v Temperature: 0℃-60℃ Current: < 1000mA Weight: 38g Dimensions: 40.8 x 20 x 39.5 mm Package include: 1 x 360 Degree Continuous Rotation Servo Motor We will ship to you asap Always need 13-18 business days to ship before delivering because we ship your parcel from oversea Please wait with patience Thank you Have a nic

360 Degrees Rotary Encoder Module Bri Sensor Switch Development Board for Arduino 5V Rotary Encoder Module Bri Sensor Development Rotating AVR Singlechip for Arduino Descriptions: 1. By rotating the rotary encoder can be counted in the positive direction and the reverse direction during rotation of the output pulse frequency. 2. Unlike rotary potentiometer count, this rotation counts are not limited. 3. With the buttons on the rotary encoder can be reset to its initial state, that starts counting from 0. 4. It is suitable for those who love DIY or are interrested in single chip, such as: teachers and students to learn the actual microcontroller courses and so on. Specifications: Material: Electronic components + PCB Size: approx. 31*19*29mm /1.22*0.75*1.14" Working voltage: 5V Pulse circle: 20 Note: Please allow 1-3mm differs due to manual measurement. Due to the different display and different light, the picture may not show the actual color of the item. Thanks for your understanding. Dear Vietnamese friends, we are sellers from China. Our products are rich and varied, and there are plenty of stos. If you have any questions, you can ask me.

Description: Product Name: Module Material: electronic components + PCB Main color: black Working voltage: 5V Pulse circle: 20 Package Contents: 5 x Module 1 x box packaging Note: The colors deviation might differ due to different monitor settings, please kindly understand. Please tell us first when you have any problem, we will give you the best service and solve the problem ASAP. Thank you so

360 Degree Continuous Rotary Servo Motor for Arduino SFeatures: Applies to model airplane / Model car / robot Torque: 5.5kg/cm (at 4.8V) Speed: 0.22sec/60°(at 4.8V) Working voltage: 4.8v-6v Temperature: 0°C-60°C Current: < 1000mA Weight: 38g Dimensions: 40.8 x 20 x 39.5 mm Package include: 1 x 360 Degree Continuous Rotation Servo

Description: Product Name: Module Material: electronic components + PCB Main color: black Working voltage: 5V Pulse circle: 20 Package Contents: 5 x Module 1 x box packaging Note: The colors deviation might differ due to different monitor settings, please kindly understand. Please tell us first when you have any problem, we will give you the best service and solve the problem ASAP. Thank you so

The handle can also be pressed / clicked as an on-off switch or menu selection. Rotary encoder xxfeature for arduino: - a potentiometer-like module that works digitally. (Not ohm resistance) By sending digital signals that would later be translated by arduino as rounds. - it doesn 't have a perimeter of rotation like a potentiometer. - these modules can be used to calculate the rotation in the forward or backwards direction during rotation. - with the switch on the rotary, reset can start the calculation

360 Degrees Rotary Encoder Module For Arduino Brick Sensor Switch Development Board KY-040 With Pins Features: 100% Brand new and high quality. Material: Electronic components + PCB Size: About 31 * 19 * 29mm / 1.22" * 0.75" * 1.14" Main color: Black Working voltage: 5V Pulse circle: 20 By rotating the rotary encoder can be counted in the positive direction and the reverse direction during rotation of the output pulse frequency, unlike rotary potentiometer count, this rotation counts are not limited. With the buttons on the rotary encoder can be reset to its initial state, that starts counting from 0. Package Included: 1 x Rotary Encoder Module Brick Sensor Development Board For Arduino We deal in wholesale and retail Feel free to contact us Skype:winniecai11 Whatsapp +86 13725560553 #360 #Degrees #Rotary #Encoder #Module #For #Arduino #Brick #Sensor #Switch #Development #Board #KY-040 #With

Working principles: Increment encoder is a rotary sensor that converts rotational displacement to a series of digital pulse signals. These pulses are used to control angular displacement. The principle of optoelectronic scanning is used for the conversion of angular displacement in eltra encoder. A reading system consists of a radial dial consisting of alternate transmission windows and opaque windows (Dockboard) Based on the rotation, also vertically irradiated by an infrared source, light project the image of the dockboard onto the receiver surface. The receiver is covered with a layer of diffraction grating, it has the same window width as the dock. The receiver 's work is to feel the change in disk rotation, the light change is then converted into corresponding electrical changes. Then raise the low-level signal to a higher level, and produces square pulses without any interference, this must be handled by electronic circuits. The reading system usually uses differential method, compare the different signals of two waveforms but with a phase difference of 180°, to improve the quality and stability of output signals. Readings are formed on the basis of differences between two more signals, thus eliminating interference The increment encoder gives two phase square wave, their phase difference is 90°, usually called channel a and b. One of the channels gives information related to rotation speed, at the same time, sequential comparison by two channel signals, get information about the direction of rotation. There is also a special signal called z or zero channel, the channel gives the absolute zero of the encoder, this signal coincides with the centerline of a channel square wave. Grating differential error、 cd-rom eccentric、 bearing eccentricity、 error introduced by electronic reader and the inaccuracy of optical part. The unit of measurement that determines the accuracy of the encoder is the electrical degree, the encoder precision determines the pulse fraction generated by the encoder. The following 360° electrical metrics are used to indicate the rotation of the mechanical shaft, the rotation of the axis must be a complete cycle. Know how much mechanical angles are equivalent to 360 degrees of electrical power, you can calculate it using the following formulas: 360 360°/n° / The error of the encoder is represented by the maximum deviation of two continuous pulse waves in the electrical angle. Error exists in any encoder, this is caused by the above factors. The maximum error of eltra encoder is 25 electrical angle (Under any conditions declared), equivalent to 7%, and phase difference of 90° (Electrical) The maximum deviation between the two channels is 35 electrical degrees equal to the rated deviation of around 10% Uvw incremental encoder In addition to the traditional encoders mentioned above, there are also incremental encoders integrated with other electrical output signals. The incremental encoder integrated with uvw is an example

Dear, welcome to walkaround, here are your favorite products, welcome to buy, we also provide 24H online Q&A to solve your problems. About product, please look down~ 360 Degrees Rotary Encoder Module Brick Sensor Switch Development Board for Arduino 5V Rotary Encoder Module Brick Sensor Development Rotating AVR Singlechip for Arduino Descriptions: 1. By rotating the rotary encoder can be counted in the positive direction and the reverse direction during rotation of the output pulse frequency. 2. Unlike rotary potentiometer count, this rotation counts are not limited. 3. With the buttons on the rotary encoder can be reset to its initial state, that starts counting from 0. 4. It is suitable for those who love DIY or are interrested in single chip, such as: teachers and students to learn the actual microcontroller courses and so on. Specifications: Material: Electronic components + PCB Size: approx. 31*19*29mm /1.22*0.75*1.14" Working voltage: 5V Pulse circle: 20 Note: Please allow 1-3mm differs due to manual measurement. Due to the different display and different light, the picture may not show the actual color of the item. Thanks for your understan

We can't upload them all because of the wide variety of electronic components we operate. if you can't find the models you need in our store, please contact us. we 'll offer you a first @ - @ time quotation and make a large number of contacts with the store.. 360 degree rotating encoder module electronic rotating potentiometer for arduino knob module ky

【aosu•OAS】Features: Applies to model airplane / Model car / robot Torque: 5.5kg/cm (at 4.8V) Speed: 0.22sec/60°(at 4.8V) Working voltage: 4.8v-6v Temperature: 0°C-60°C Current: < 1000mA Weight: 38g Dimensions: 40.8 x 20 x 39.5 mm Package include: 1 x 360 Degree Continuous Rotation Servo

Can be the lowest price of the supplier, the spot is hot.~~~ We are shipping overseas The price in the store is the lowest price. Since we are an overseas direct sales store, the goods will arrive longer. Point, usually 8 to 12 days after the order is delivered, such as urgent users, please be careful! ! ! Those who cancel the order and do not pick up the goods will be held accountable for their personal responsibility! ! ! Important Tips→If you are charged [tariff] [tariff] [tariff], contact our customer service to let us compensate some of the tax, remember to remember Shopping Tips: So the style and size are available, but due to inventory changes It is best to consult us or talk about it, or you can note the color size of the style you need when you subscript. We are easy to arrange shipping within 3-5 working days! Please be sure to subscript, thank you! ! ! The store will only be replaced, except for major defects, the exchange will be paid as a shipping subsidy to the manufacturer, thank you

Brand Name : MLLSE Compatible Brand/Model : None Original : yes Capacitor and Resistor Electrolytic Capacitor Ceramics capacitors 1/4W Resistor Thermistor Triode Transistor TO-92 TO-220 SOT-23 SOT-89 Integrated Circuit DIP8 DIP14 DIP16 DIP18 SOP Diode LED DO-41 DO-35 DO-27 R-6 SMA Rectifier B

360 Degrees Rotary Encoder Module Brick Sensor Switch Development Board for Arduino 5V Rotary Encoder Module Brick Sensor Development Rotating AVR Singlechip for Arduino Descriptions: 1. By rotating the rotary encoder can be counted in the positive direction and the reverse direction during rotation of the output pulse frequency. 2. Unlike rotary potentiometer count, this rotation counts are not limited. 3. With the buttons on the rotary encoder can be reset to its initial state, that starts counting from 0. 4. It is suitable for those who love DIY or are interrested in single chip, such as: teachers and students to learn the actual microcontroller courses and so on. Specifications: Material: Electronic components + PCB Size: approx. 31*19*29mm /1.22*0.75*1.14" Working voltage: 5V Pulse circle: 20 Note: Please allow 1-3mm differs due to manual measurement. Due to the different display and different light, the picture may not show the actual color of the item. Thanks for your understanding. Included: 1 x Sensor Switch Development

Welcome to my store thank you for visiting. All produsts are good quality! We will check and pack well before sending out. 360 Degrees Rotary Encoder Module Brick Sensor Switch Development Board for Arduino 5V Rotary Encoder Module Brick Sensor Development Rotating AVR Singlechip for Arduino Descriptions: 1. By rotating the rotary encoder can be counted in the positive direction and the reverse direction during rotation of the output pulse frequency. 2. Unlike rotary potentiometer count, this rotation counts are not limited. 3. With the buttons on the rotary encoder can be reset to its initial state, that starts counting from 0. 4. It is suitable for those who love DIY or are interrested in single chip, such as: teachers and students to learn the actual microcontroller courses and so on. Specifications: Material: Electronic components + PCB Size: approx. 31*19*29mm /1.22*0.75*1.14`` Working voltage: 5V Pulse circle: 20 Note: Please allow 1-3mm differs due to manual measurement. Due to the different display and different light, the picture may not show the actual color of the item. Thanks for your understanding. Package Content: 1 x Sensor Switch Development

Description: Product Name: Module Material: electronic components + PCB Main color: black Working voltage: 5V Pulse circle: 20 Package Contents: 5 x Module 1 x box packaging Note: The colors deviation might differ due to different monitor settings, please kindly understand. Please tell us first when you have any problem, we will give you the best service and solve the problem ASAP. Thank you so

[foodtaste+stock]360 Degree Continuous Rotary Servo Motor for Arduino Smart CarFeatures: Applies to model airplane / Model car / robot Torque: 5.5kg/cm (at 4.8V) Speed: 0.22sec/60°(at 4.8V) Working voltage: 4.8v-6v Temperature: 0°C-60°C Current: < 1000mA Weight: 38g Dimensions: 40.8 x 20 x 39.5 mm Package include: 1 x 360 Degree Continuous Rotation Servo

Arduino Xbee Shield được sử dụng với các phiên bản Xbee Standard và Xbee Pro giúp dễ dàng kết nối module RF Xbee với Arduino và Máy tính, mạch tích hợp IC chuyển nguồn 3.3VDC, led báo trạng thái và công tắc Switch giúp chọn chế độ kết nối UART trực tiếp của Xbee với Arduino hoặc USB máy tính một cách dễ dàng. 1. Thông số kĩ thuật: Có thể cắm chồng nhiều shield lên nhau 3 đèn LED hiện thị trạng thái của Xbee: ON/SLEEP, RSSI, ASS Có IC cung cấp dòng lên tới 500mA Hỗ trợ các module Xbee Standard và Pro 2. Tham khảo Thư viện Arduino 1 Thư viện Arduino 2 Hướng dẫn sử

Hello everyone, our company is in Shenzhen。we specialize in selling electronic components. When we receive your order, we will process your order within 24 hours. If you order many items, we may need more time to process, it will not be more than 5 days, please be patient. Genaral it need 1-2weeks arrive your hand.if you chat with us , we donot reply you, donot worry , we are try to handle your order.so pls donot cancel o

Dc to dc converter step down module Stock a lot, just order it. The stock now doesn 't match the picture, there' s no 100. Sometimes the stuff that comes from the agent is different 2, there 's a 100, there' s nothing written. Sometimes every unit in a plastic static wrap. Sometimes it 's not wrapped in plastic. It 's the same thing i think, but if you have a special need, you have to write 100 and you have to wrap each unit, you have to ask which stock is available. The shipment must be bubble gan, even though the purchase of our 1 unit is bubblewarp. Just as much as you can buy over 30rb ya gan or mix it with other goods to be above 30rb, let 's not lose our pack.. Specs: Voltage input: 4.75v-23v Voltage output: 1v-17v Output current: Peak 3a, continuous 1.8a Power: 10w Efficacy: Up to 95% (@ vin = 5v, vout = 3.3v, iout = 300ma) Switching frequency: 340khz Output ripple: 30mv (no load) Current supply: 1.5ma (no load) Working temperature: - 40 ~ + 85 Module size: 17x11

Thời gian giao hàng dự kiến cho sản phẩm này là từ 7-9 ngày 100% hàng mới, chất lượng cao. Chất liệu: Linh kiện điện tử + PCB Kích thước: Khoảng 31 * 19 * 29mm / 1.22 " * 0.75 " * 1.14 " Màu sắc chính: Đen Điện áp hoạt động: 5V Vòng tuần hoàn mạch modul

5v unlimited turn 360 degree digital encoder rotary for arduino cheap Description: A module that resembles a potentiometer but works digitally (not ohm resistance) by sending digital signals that arduino would later translate as a spin. It doesn 't have a perimeter of rotation like potentiometers. The module can be used to calculate the rotation in the forward or backwards direction during rotation. With the switch on the rotary, the reset can start the calculation of 0. Feature: 1. 100% brand new and high quality. 2. Electronic components + pcb material 3. Size: About 31x19 x 29mm / 1.22x0.75x1.14 4. Play color: 5. Working voltage: 5v. 6. Pulse circle

Description: 100% brand new and high quality High speed, stable and shock proof. Metal gear and double ball bearing Color: Black Compatible with most standard receiver connector: JR/Futaba etc. Stall Torque: 13 kg / cm Operating voltage: 4.8 - 7.2V. Steering Angle:0-360° Material:Metal Package includes: 1 x RC Servo Motor with accessories(other accessories demo in the picture is not included.) Note:The real color of the item may be slightly different from the pictures shown on website caused by many factors such as brightness of your monitor and light bright

Dear, welcome to Redkee, here are the latest season products for you to choose, the hottest products, the best prices, we also provide 24H online Q & A, if you have any questions, please consult our customer service, for more information about the product, Please read on ~ 360 Degrees Rotary Encoder Module Brick Sensor Switch Development Board for Arduino 5V Rotary Encoder Module Brick Sensor Development Rotating AVR Singlechip for Arduino Descriptions: 1. By rotating the rotary encoder can be counted in the positive direction and the reverse direction during rotation of the output pulse frequency. 2. Unlike rotary potentiometer count, this rotation counts are not limited. 3. With the buttons on the rotary encoder can be reset to its initial state, that starts counting from 0. 4. It is suitable for those who love DIY or are interrested in single chip, such as: teachers and students to learn the actual microcontroller courses and so on. Specifications: Material: Electronic components + PCB Size: approx. 31*19*29mm /1.22*0.75*1.14" Working voltage: 5V Pulse circle: 20 Note: Please allow 1-3mm differs due to manual measurement. Due to the different display and different light, the picture may not show the actual color of the item. Thanks for your understan

MG995 180 ° / 360 ° Mô-men xoắn cao Bánh răng kim loại RC Động cơ Servo cho Bộ xe trực thăng thuyền Đặc tính: Bánh răng kim loại và ổ bi kép. Tốc độ cao, ổn định và chống sốc. Tay nghề tốt và hiệu suất tốt. Dễ sử dụng. Tuổi thọ lâu dài. Tương thích với hầu hết đầu nối bộ thu tiêu chuẩn: JR / Futaba, v.v. Sự chỉ rõ: Chất liệu: Kim loại Màu đen Điện áp hoạt động: 4.8 - 7.2V Góc lái: 0-180 ° / 0-360 ° Đóng gói: 1 x Động cơ Servo RC với các phụ

Delivery is conducted every day at work hours 5v unlimited turn 360 degree digital encoder rotary for arduino cheap Description: A potentiometer-like module but it works digitally (Not ohm resistance) By sending digital signals that would later be translated by arduino as rounds. It doesn 't have a perimeter of rotation like potentiometers. The module can be used to calculate the rotation in the forward or backwards direction during rotation. With the switch on the rotary, the reset can start the calculation of 0. Feature: 1. 100% brand new and high quality. 2. Electronic components + pcb material 3. Size: About 31x19 x 29mm / 1.22x0.75x1.14 4. Black: 5. Working voltage: 5v. 6. Pulse circle:

Delivery is conducted every day at work hours 5v unlimited turn 360 degree digital encoder rotary for arduino cheap Description: A potentiometer-like module but it works digitally (Not ohm resistance) By sending digital signals that would later be translated by arduino as rounds. It doesn 't have a perimeter of rotation like potentiometers. The module can be used to calculate the rotation in the forward or backwards direction during rotation. With the switch on the rotary, the reset can start the calculation of 0. Feature: 1. 100% brand new and high quality. 2. Electronic components + pcb material 3. Size: About 31x19 x 29mm / 1.22x0.75x1.14 4. Black: 5. Working voltage: 5v. 6. Pulse circle: