Dong co buoc nema 17

Short Height 13Ncm(18.4oz.in) holding torque FOR NEMA 17 bipolar 1.65 inchx1.65 inchx0.79 inch 4-wire 1.8 deg. step angle(200 steps/rev) Rated current 1.0A & resistance 3.5ohms This is Short Height FOR Bipolar Nema 17 stepper motor with 1.8 deg. step angle (200 steps/revolution). Each phase draws current 1A, allowing for a holding torque of 13Ncm(18.4oz.in). Color: sier material: metal Electrical Specification: Manufacturer Part Number: 17HS08-1004S Motor Type: Bipolar Stepper Step Angle: 1.8 deg. Holding Torque: 13Ncm(18.4oz.in) Rated Current/phase: 1.0A Phase Resistance: 3.5ohms Inductance: 4.5mH+/-20%(1KHz) Physical Specification: Frame Size: 42 x 42mm Body Length: 20mm Shaft Diameter: 5mm Shaft Length: 20mm D-cut Length: 16.5mm Number of Leads: 4 Lead Length: 400mm Weight: 140g Connection: Black(A+), Green(A-), Red(B+), Blue(B-) Warning: Make sure the motor connect to a constant current or chopper drive controller before you test motor. Connecting the motor directly to a power supply will destroy the motor. Package Contents:1* stepper motorOnly the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

low self-inductance reactance, responsive and can avoid system error. LOW NOISE: stepper motor kit is made with introduced German craftsmanship and there is rotor rubber covering the rotor, effectively reduce the noise. DURABLE & TOUGH: tough and durable. And the matte texture in the side wall can increase friction. WIDE APPLICATION: This small motors can be used in various area, such as stage lighting; engraving; textile machinery; equipment; placement machine; non-standard equipment; 3D printer; automation equipment, and etc.. Product name: Bipolar 42 Stepper Motor Holding torque: 0.46 Nm/ 65 oz-in Working voltage: DC 9-42V Rated current: 1.7A Resistance: 2.1 ohm Inductance: 4mH Rotor inertia: 55gcm2/ 0.30oz-in2 Weight: 0.28kg Phrase: 2 Step angle: 1.8 degree Wiring: Black (A+); Green (A-); Red (B+); Blue (B-) Application: Stage lighting; engraving; textile machinery; equipment; placement machine; non-standard equipment; 3D printer; automation equipment colour:black Material:metal size:42x42x40mm Package Contents: 1* 42*42*34 stepper motor 1* Link line Warm Tips: Please note that this motor cannot be connected to the power supply directly. It should be connected to a constant current driver, otherwise, it will destroy the motor. Please ensure that the output current is not higher than the rated current of the motor (1.7A) or exceed the working voltage range of the motor (DC 9-42V). Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

Short Height 13Ncm(18.4oz.in) holding torque FOR NEMA 17 bipolar 1.65 inchx1.65 inchx0.79 inch 4-wire 1.8 deg. step angle(200 steps/rev) Rated current 1.0A & resistance 3.5ohms This is Short Height FOR Bipolar Nema 17 stepper motor with 1.8 deg. step angle (200 steps/revolution). Each phase draws current 1A, allowing for a holding torque of 13Ncm(18.4oz.in). Color: sier material: metal Electrical Specification: Manufacturer Part Number: 17HS08-1004S Motor Type: Bipolar Stepper Step Angle: 1.8 deg. Holding Torque: 13Ncm(18.4oz.in) Rated Current/phase: 1.0A Phase Resistance: 3.5ohms Inductance: 4.5mH+/-20%(1KHz) Physical Specification: Frame Size: 42 x 42mm Body Length: 20mm Shaft Diameter: 5mm Shaft Length: 20mm D-cut Length: 16.5mm Number of Leads: 4 Lead Length: 400mm Weight: 140g Connection: Black(A+), Green(A-), Red(B+), Blue(B-) Warning: Make sure the motor connect to a constant current or chopper drive controller before you test motor. Connecting the motor directly to a power supply will destroy the motor. Package Contents:1* stepper motorOnly the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

3x Stepper motor link line: 1* A+ 2* B Material:ABS New stepper motor cable for the most common NEMA 17 steppers found on 3D printers. Length is great for swapping to a Bowden (remote) extruder where your existing cable may not be long enough, or when moving your control board to the outside of an enclosure. Colour:colour size:Length 1M This has the standard JST stepper connector with 4 pins wired on the stepper end, and a 4-pin 2.54mm dupont connector on the controller board end. Package Contents: 3x Stepper motor link lineOnly the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

Product Features: 1. Applicable to NEMA 17 stepper motor or V-Slot Linear; 2. The slot can easily adjust the tension, and multiple holes can accomate and design; Product specifications: Version - V1 6063 - T6 board 3 mm thick Material:aluminum Colour: Black Product weight: 21.4g Package Contents: 1 * Motor Mount Plate Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

Lưu ý: Sản phẩm mới 100% Tính năng sản phẩm Đầu nối XH-2.54 cắm, cài đặt và thay thế dễ dàng, nhanh chóng Phần trục phẳng cho mô-men xoắn tốt hơn Bao gồm những gì (1) Động cơ bước Nema 17HS4401 (1) Dây nối 4 lõi, 2 đầu XH-2.54 Thông số kỹ thuật sản phẩm Kích thước trục: 5 mm Mô-men xoắn: 0,45 N.m Góc bước: 1,8 Dòng đỉnh: 1,68A / pha Lỗ gắn M3 4 dây Bi-Polar Điện áp: 12-24VDC (Khuyến nghị) Tuân thủ RoHS Bản vẽ kích t

#NEMA #17 #Steppr #Motor #Accessories #Plastic #Bracket #Support #Mounting #L #Type #Bracket #Mount #42 #Stepping NEMA 17 Steppr Motor Accessories Plastic Bracket Support Mounting L Type Bracket Mount 42 Stepping Stepper Motor Nema17 Motor Holder NEMA 17 42 Stepping Stepper Motor Plastic Bracket Support Mounting L Type Holder Specifications: Type : Mounting bracket Model : 42 stepper motor bracket Material : ABS plastic Package includes: (Without retail package) 1 x Brac

Welcome to My Store. Our concept is"Customer First.Service Attentively" !  Please view the product description before you make order, thanks! 1. Strengthen the PCB in the motor and adopt a unique stator process 2.The stator teeth of the motor are evenly ed and the inner hole has high precision. The speed is stable and accurate during the working process. 3. The structure is stable and does not jam the machine. The surface of the motor rotor is coated with imported epoxy resin, the rotor is integrally sealed and cured at high temperature, and the rotor After processing the outer garden, the machining residues such as iron pins and the like are not easy to be found in the tooth groove, and the motor is stable for long-term use without the risk of jamming. 4.The overall stability of the motor is high via Kossel, Prusa l3, Ultmaker, corexy and other motors. Uniform rotation speed, low noi5.Suitable for engraving machine, printer, medical equipment, embroidery machine, stage lighting, textile automation,printing,packaging and other industries automation equipment. Manufacturer Part Number:17HS8401 Step Angle:1.8° Step Accuracy :5% Holding Torque:59Ncm(83.6oz.inch) Rated Current/phase:2.0A Phase Resistance:1.4ohms Voltage:2.8V Inductance:3.0mH±20%(1KHz) colour: black Material: Aluminum alloy Size:42x42x48mm Package Contents: 1 set x of Stepper Motor Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

Short Height 13Ncm(18.4oz.in) holding torque FOR NEMA 17 bipolar 1.65 inchx1.65 inchx0.79 inch 4-wire 1.8 deg. step angle(200 steps/rev) Rated current 1.0A & resistance 3.5ohms This is Short Height FOR Bipolar Nema 17 stepper motor with 1.8 deg. step angle (200 steps/revolution). Each phase draws current 1A, allowing for a holding torque of 13Ncm(18.4oz.in). Color: silver material: metal Electrical Specification: Manufacturer Part Number: 17HS08-1004S Motor Type: Bipolar Stepper Step Angle: 1.8 deg. Holding Torque: 13Ncm(18.4oz.in) Rated Current/phase: 1.0A Phase Resistance: 3.5ohms Inductance: 4.5mH+/-20%(1KHz) Physical Specification: Frame Size: 42 x 42mm Body Length: 20mm Shaft Diameter: 5mm Shaft Length: 20mm D-cut Length: 16.5mm Number of Leads: 4 Lead Length: 400mm Weight: 140g Connection: Black(A+), Green(A-), Red(B+), Blue(B-) Warning: Make sure the motor connect to a constant current or chopper drive controller before you test motor. Connecting the motor directly to a power supply will destroy the motor. Package Contents:1* stepper motorOnly the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

#Titan #Extruder #Stepper #Motor #4-lead #Nema #17 #22mm #42 #Motor #for #3D #Printer 3D printer parts Titan Step motor for Titan Extruder 3D printer extruder 42x42x23mm Product name: Titan step motor Size:42x42x23mm Phase: 2 Phase Voltage: 12V Current: 0.8A/Phase Resistance: 4.0 ± 10%Ω/Phase Inductance: 3.2 ± 20% mH/Phase Holding Torque: 16 N.cm Insulation Class: B Step Angle: 1.8±5% /STEP Warning: Make sure the motor connect to a constant current or chopper drive controller before you test motor. Connecting the motor directly to a power supply will destroy the motor. Packing list: 1 x Titan step motor 1 x 1m C

#dongcobuoc , #nema17 , #42hs48 , #dongconema , #size42 , #dongcosize42 Description Động cơ bước NEMA17 – 0.55Nm – 1.5a – 42*48mm Sản phẩm được bảo hành 6 tháng. Thông số kỹ thuật chính: Kích thước mặt bích: 42×42 mm. Chiều dài thân: 48 mm. Dòng chịu tải: 1.5A. Moment xoắn: 0.55Nm Góc bước: 1.8°/step Driver điều khiển động cơ :https://shopee.vn/Driver-%C4%91i%E1%BB%81u-khi%E1%BB%83n-%C4%91%E1%BB%99ng-c%C6%A1-b%C6%B0%E1%BB%9Bc-P5C-i.175913088.7013459362 --------------------------------------------------------------------------------- INBOX ĐỂ ĐƯỢC TƯ VẤN THÊM VỀ SẢN PHẨM SĐT liên hệ : 0983421523 #machviet #driver #machvietcnc #cnc #bodieukhien #dongcobuoc #hybridservo #acservo #servo #mach3 #ncstudio #cardnc #raytruot #contruot #xcmcu #plasma #leadshine #jmc #sumtor #dongcobuoc57 #dongcobuoc86 #tamchanbui #vitme #cuduc #spindle #cuducvitinh #bientan #inverter #ykhmi #hmi #plc #nmrv #gear #giamtoc #giamtochanhtinh #couping #khopnoi #d

2Pcs NEMA 17 42 Stepper Motor Plate Fixed Bracket For 3D Printer 2020 Profiles Features: 100% brand new and high quality. Good quality products, ensure that your printer working smoothly, ensure your printer security. Used for 2020 industrial aluminium profile, both for EU standard and non-standard. Specifications: Item Type: Motor Mounting Plate Material: Aluminum Color: Silver / Black(Optional) Size: 42mm X 60mm Thickness:2.5mm Quantity: 2Pcs Package includes: (Without retail package) 2 X Motor Mounting Plates

động cơ bước nema 17 size 42 mới 100% kích thước 42x42x36 đầu cốt 5mm khuyết 1 bên để dễ dàn bắt puly chống xoay (tuột bước,mất bước) bước 1.8 độ - 1.2A sản phầm gồm: 1 motor nema 17 size 42x42x36 #stepmotor

Product Features: 1. Applicable to NEMA 17 stepper motor or V-Slot Linear; 2. The slot can easily adjust the tension, and multiple holes can accomate and design; Product specifications: Version - V1 6063 - T6 board 3 mm thick Material:aluminum Colour: Black Product weight: 21.4g Package Contents: 1 * Motor Mount Plate Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

Colour:colour Material:ABS Helpful Support Quick Shipping New stepper motor cable for the most common NEMA 17 steppers found on 3D printers. size:Length 1M Length is great for swapping to a Bowden (remote) extruder where your existing cable may not be long enough, or when moving your control board to the outside of an enclosure. This has the standard JST stepper connector with 4 pins wired on the stepper end, and a 4-pin 2.54mm dupont connector on the controller board end. Package Contents:1 x Stepper motor link line Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

Current / Phase:1.7A Phase:2 Couple Celebration:4000 Step Angle (Degrees):1.8 Type:Hybrid el Number:17HS4401S-PG518 Part number:17HS4401S-PG518 Gear Ratio:5.18:1 Manufacturer Part Number 17HS4401S-PG518 Bipolar Motor Type step by step Step angle (with gearbox) 1.8 ° PAR 1.68Nm Nominal current / phase 1.68A 1.65 ohm resistance phase Recommended voltage 12-24 V Inductance 3.2mH +/- 20% (1 KHz) Planetary type gearbox Gear ratio (exact gear ratio) 5 + 2/11 Efficiency 90% Backlash without load less than equal 1 ° Maximum torque 2 nm (283ozin) Permissible torque of 4Nm (566ozin) Max Axial Load Axle 50N Maximum radial load shaft 100N colour:black Material:metal Package Contents: 1* motor 1* lineOnly the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

3D printer motor with high torque 59Ncm(83.6oz.in) holding torque NEMA 17 bipolar 1.65 inch x1.65 inch x1.89 inch 4-wire Build with 39.37 inch ( 1m) Cable and 0.1 inch pitch Connector Rated current 2.0A & resistance 1.4ohms Colour: Black material: metal Package Contents: 1 * 17 Stepper MotorOnly the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

★★ Welcome to buy ★★ ☪Before placing an order, please confirm the purchase parameters and receipt information to avoid delivery failure. The store supports COD and will check the goods before shipment. If you receive damage, please contact us immediately and we will handle it for you ◕‿-｡ Features: 1. Wide Application: This product is suitable for NEMA 17 stepper motors / V-Slot Linear. 2. Porous Design: The slot can be easily adjusted for tension, with multiple holes for accommodation and design. 3. Convenient to Use: This NEMA 17 motor mount plate is designed to easily allow for the modular connection of a NEMA 17 stepper motor. 4. Perfect Finishing: Black anodized. 5. Good Quality: The premium product guarantee that your printer working smoothly, make sure your printer security. Specification: 6063 : T6 board Color: black Item name: Nema 17 Stepper Motor Mount plate Material: aluminum Finishing: black anodized Application: Use for Nema 17 stepper motors Package List: 1 * NEMA 17 Motor Mount Pl

Description: Product Name: Vibration Damper It can effectively reduce shock, sed for reducing 3D printer stepper motor noise and vibration Suitable for 42 Stepper Motor/3D Printer Motor/MEMA 17 Stepper Material: Aluminium Alloy Diagonal Length: 5.2cm, 3.5cm; Diameter: 5mm Specification: Size:52x35x5mm Package Includes: 1Piece Stepper Motor Vibration Dampener Note: Please allow 0.5-1 inch difference due to manual measurement.(1 inch=2.54cm) Due to the difference between different monitors, the picture may not reflect the actual color of the item. Please understand. Thank

_______ Cửa hàng Apill chào mừng ♤ ___________ ✔Ready Stock !! Mua ngay! ✔COD ✔ Kiểm tra chất lượng ✔ Giá tốt nhất ✔Brand mới 100% Vận chuyển trong 1 ngày ★ Bất ngờ cho bạn ★ Quà tặng miễn phí: Theo dõi cửa hàng ❤ Nhật Like Giống 5 mục: Vận chuyển ưu tiên Gửi cho tôi Ảnh chụp màn hình và tin nhắn theo đơn đặt hàng của bạn: "Quà tặng miễn phí" nếu không sẽ bỏ lỡ Tip (Mẹo: Chúng tôi sẽ dựa trên khách của bạn ở quốc gia của bạn để gửi phích cắm bộ chuyển đổi tương ứng) Các nhà bán lẻ bán buôn được hoan nghênh đàm phán kinh doanh lâu dài với chúng tôi! __________________ Thông tin sản phẩm❀ __________________ Feature: 1. Suitable for Nema 17/23 motors, their power levels are optimized to reduce power consumption and improve dynamic performance. 2. Low noise during operation, with highest efficiency and best engine torsion 3. The product has high integration and energy efficiency 4. Made of high quality PCB and metal material, durable and long service life 5. High quality and great processing of the product can provide stable performance Specification: Item Type: TMC5161 V1.0 Motor DriverApplicable: Nema17 / 23 Color: As picture show Material: PCB + metal Package List: 1 x TMC5161 V1.0 Driver 1 x Heat S

Short Height 13Ncm(18.4oz.in) holding torque FOR NEMA 17 bipolar 1.65 inchx1.65 inchx0.79 inch 4-wire 1.8 deg. step angle(200 steps/rev) Rated current 1.0A & resistance 3.5ohms This is Short Height FOR Bipolar Nema 17 stepper motor with 1.8 deg. step angle (200 steps/revolution). Each phase draws current 1A, allowing for a holding torque of 13Ncm(18.4oz.in). Color: sier material: metal Electrical Specification: Manufacturer Part Number: 17HS08-1004S Motor Type: Bipolar Stepper Step Angle: 1.8 deg. Holding Torque: 13Ncm(18.4oz.in) Rated Current/phase: 1.0A Phase Resistance: 3.5ohms Inductance: 4.5mH+/-20%(1KHz) Physical Specification: Frame Size: 42 x 42mm Body Length: 20mm Shaft Diameter: 5mm Shaft Length: 20mm D-cut Length: 16.5mm Number of Leads: 4 Lead Length: 400mm Weight: 140g Connection: Black(A+), Green(A-), Red(B+), Blue(B-) Warning: Make sure the motor connect to a constant current or chopper drive controller before you test motor. Connecting the motor directly to a power supply will destroy the motor. Package Contents:1* stepper motorOnly the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

1 pcs CNC Gantry Plate & 1 pcs Stepper Motor 1. Rapid assembly continues; 2. Various standard hole sizes for belts, screws and other attachment options. 3. Stability, fixedness, applicability, and flexibility; 4. Compatible with V-Slot linear guides Colour: Black material: metal Gantry plate: Thickness: 3mm Size: 128x88x3mm Surface treatment: black anodizing 17 Stepper Motor: 3D printer motor with high torque 59Ncm(83.6oz.in) holding torque NEMA 17 bipolar 1.65 inch x1.65 inch x1.89 inch 4-wire Build with 39.37 inch ( 1m) Cable and 0.1 inch pitch Connector Rated current 2.0A & resistance 1.4ohms Package Contents: 1 * Gantry plate 1 * 17 Stepper MotorOnly the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

Product Features: 1. Applicable to NEMA 17 stepper motor or V-Slot Linear; 2. The slot can easily adjust the tension, and multiple holes can accomate and design; Product specifications: Version - V1 6063 - T6 board 3 mm thick Material:aluminum Colour: Black Product weight: 21.4g Package Contents: 1 * Motor Mount Plate Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

Product Features: 1. Applicable to NEMA 17 stepper motor or V-Slot Linear; 2. The slot can easily adjust the tension, and multiple holes can accomate and design; Product specifications: Version - V1 6063 - T6 board 3 mm thick Material:aluminum Colour: Black Product weight: 21.4g Package Contents: 1 * Motor Mount Plate Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

3D printer motor with high torque 59Ncm(83.6oz.in) holding torque NEMA 17 bipolar 1.65 inch x1.65 inch x1.89 inch 4-wire Build with 39.37 inch ( 1m) Cable and 0.1 inch pitch Connector Rated current 2.0A & resistance 1.4ohms Colour: Black material: metal Package Contents: 1 * 17 Stepper MotorOnly the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

1pcs step motor with cable & 2pcs Z-axis with screw bearing with screw, Boat nut, bearing, top wire Holding Torque:120mN.m Type:Hybrid Product name: Titan step motor Phase: 2 Phase Voltage: 12V It's a Z-Axis Leadscrew Top Mount for 3D Printer Apply to: CR-10, Tornado, Ender 3 etc Current: 0.7 A/Phase Resistance: 4.0 +/- 10%Ω/Phase Inductance: 3.2 +/- 20% mH/Phase Holding Togque: 14 N.cm Insulation Class: B Step Angle: 1.8 +/- 5% /STEP Color: Sier-black & black Material: metal & Metal + ABS step motor Size:42 x 42 x 23mm Package Contents: 1 x step motor 1 x cable 2 x Z-axis with screw bearing 4 x screw 4 x Boat nut 2 x bearing 2 x top wireOnly the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

Product Features: 1. Applicable to NEMA 17 stepper motor or V-Slot Linear; 2. The slot can easily adjust the tension, and multiple holes can accomate and design; Product specifications: Version - V1 6063 - T6 board 3 mm thick Material:aluminum Colour: Black Product weight: 21.4g Package Contents: 1 * Motor Mount Plate Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

Động cơ bước - Step Nema 17 (Size 42) kèm Cáp Động Cơ Bước - Kích thước trục (Cốt): 5mm là kích thước thông dụng nhất hiện nay. - Độ phân giải: 1.8 độ, 200 xung/ 1 vòng. - Kích thước: 42x42x35 (DxRxC). - Dòng: 1.2 -1,4A tùy lô. Lưu ý động cơ mạnh hay không phụ thuộc vào dòng và moment (moment tỷ lệ thuận độ lớn của cuộn đồng tức chiều cao của động

#Titan #Extruder #Stepper #Motor #4-lead #Nema #17 #22mm #42 #Motor #for #3D #Printer Titan Extruder Stepper Motor 4-lead Nema 17 22mm 42 Motor for 3D Printer 3D printer parts Titan Step motor for Titan Extruder 3D printer extruder 42x42x23mm Product name: Titan step motor Size:42x42x23mm Phase: 2 Phase Voltage: 12V Current: 0.8A/Phase Resistance: 4.0 ± 10%Ω/Phase Inductance: 3.2 ± 20% mH/Phase Holding Torque: 16 N.cm Insulation Class: B Step Angle: 1.8±5% /STEP Warning: Make sure the motor connect to a constant current or chopper drive controller before you test motor. Connecting the motor directly to a power supply will destroy the motor. Packing list: 1 x Titan step motor 1 x 1m C