Board cnc shield

Giới thiệu Board Arduino CNC Shield V3. CNC shield V3là board mở rộng của Arduino UNO R3 dùng để điều khiển các máy CNC mini. Board có 4 khay dùng để cắm các mô đun điều khiển động cơ bước A4988, khi đó board có thể điều khiển3 trục X, Y, Z và thêm một trục thứ 4 tùy chọn trên các máy CNC mini. Thông số kỹ thuật Tương thích GRBL (mã nguồn mở chạy trên Arduino UNO R3 để điều khiển CNC mini) Hỗ trợ lên tới 4 trục (trục X, Y, Z và một trục thứ tư tùy chọn) Hỗ trợ tới 2 Endstop (cảm biến đầu cuối) cho mỗi trục Tính năng điều khiển spindle Tính năng điều khiển dung dịch làm mát khi máy hoạt động Sử dụng các mô đun điều khiển động cơ bước, giúp tiết kiệm chi phí khi thay thế, nâng cấp Thiết lập độ phân giải bước động cơ bằng jump đơn giản Thiết kế nhỏ gọn, các đầu nối tiêu chuẩn thông dụng Điện áp nguồn cấp đa dạng từ 12V tớ

Mũi dao CNC xoắn 1 ME. Ứng dụng : cắt tạo hình các loại gỗ khỏi phôi. #mũi #phay #cnc #endmill #titan - Thông số kĩ thuật : + Đường kính trục : 3.175mm - 4mm + Đường kính Mũi : 1-1.5-2mm. + Độ dài mũi : * Mũi 1.0mm - dài max 3mm. * Mũi 1.5mm - dài max 12mm. * Mũi 2.0mm - dài max 17mm. Xin vui lòng liên hệ shop để được tư vấn thêm : 0932.616.648 - zalo/viber/ Whatsapp.

dây 4pin kết nối board mạch cnc shield, ramps 1.4,1.5, .... với động cơ bước, cảm biến, công tắc... dây 4pin kết nối board mạch cnc shield, ramps 1.4,1.5, .... với động cơ bước, cảm biến, công tắc... #3dlinhkien #linhkien3d #phukien3d #mayin3d cung cấp linh kiện máy in 3d cnc

BOARD MỞ RỘNG CNC SHIELD V4 ---------------------------------------------- IoT4U - www.iot4u.vn - Cung cấp linh kiện điện tử - Thiết bị IoT, Arduino, Modules - LED , Nguồn tổ ong, Mạch điều khiển LED ĐT/Zalo: 09056

CNC Shield Board: Latest Arduino CNC Shield Version 3.0 GRBL 0.9 compatible 4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13) 2 x End stops for each axis (6 in total) Coolant enable Compatible with A4988 or DRV8825 stepper driver Operating voltage: 5V Digital I/O pins: 14 (including 6 with PWM capability) I-I/O pin output current: 40mA max 3.3V output current: 150mA max Flash memory: 32 kB (0.5kB used by bootloader - included) Static RAM (SRAM): 2 kB EEPROM: 1 kB Clock speed: 16MHz A4988 Stepper Motor Driver Board is a breakout board for Allegro's A4988 DMOS Micro-stepping Driver with Translator and Overcurrent Protection; Low RDS (On) Output Automatic current decay mode detection / selection Mix with slow current decay modes Synchronous rectification for low power dissipation Internal UVLO Crossover-current protection 3.3 and 5 V compatible logic supply Thermal shutdown circuitry Ground fault protection Load short-circuit protection Five selectable step modes: full, 1/2, 1/4, 1/8 and 1/16 Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. (More generally, rewiring anything while it is powered is asking for trouble). Color: blue + red Material: metal + PC Package Contents: 1 x CNC Shield Board 1 x UNO R3 Board for Arduino 4 x A4988 Stepper Motor Driver 4 x Heat Sink Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

CNC Shield Board: Latest CNC Shield Version 3.0 for Arduino.GRBL 0.9 compatible. (Open source firmware that runs on an UNO for Arduino that turns G-code commands into stepper signals).PWM Spindle and direction pins.4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13).2 x End stops for each axis (6 in total) Coolant enable,Uses removable A4988 or DRV8825 compatible stepper drivers Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping ).Compact design.Stepper Motors can be connected with 4 pin molex connectors or soldered in place. Runs on 12-36V DC. (At the moment only the DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.),Please note that this is an unassembled kit and Basic soldering skills are needed.A4988 Stepper Motor Driver Board is a breakout board for Allegro's A4988 DMOS Micro-stepping Driver with Translator and Overcurrent Protection; please read the A4988 datasheet carefully before using this product. Low RDS (On) Output,Automatic current decay mode detection / selection,Mix with slow current decay modes.Synchronous rectification for low power dissipation,Internal UVLO.Crossover-current protection,3.3 and 5 V compatible logic supply,Thermal shutdown circuitry,Ground fault protection,Load short-circuit protection,Five selectable step modes: full, 1/2, 1/4, 1/8 and 1/16. Colour: Photo Color Material: PC+ metal Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. (More generally, rewiring anything while it is powered is asking for trouble). Note: Green or Red PCB Package Includes: 1 x CNC Shield Board 4 x A4988 Stepper Motor Driver 4 x Heat Sink Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from thereal thing. The measurement allowed error is +/- 1

Do you want to enjoy high-quality experience? Then get into our store and pick it up.！ Decription: Features: Use removable A4988 or DRV8825 compatible stepping driver. The extension board can be used for engraving machine or 3D printer driver. Compatible with GRBL 0.8. Open-source firmware operated on Arduino UNO, converting G code command into stepping signal. PWM spindle and direction pin, 4 shaft support (X, Y, Z, A - you can copy X, Y, Z or use pin D12 and D13 customize firmware perform complete shaft 4). Compact design, stepping motor can connect 4 pin connectors or be soldered. This is a set of disassembled part, and you need basic soldering skills to solder them together. CNC Expansion Board: Version: V3.0 Green 68 x 53 x 18mm / 2.67 x 2.08 x 0.7" Voltage: DC 12V to 36V (only DRV8825 driver can handle up to 36V, so please consider voltage for power supply) 4pcs A4988 Driver: 20 x 15mm / 0.78 x 0.59" Thermal Shutdown Circuit: Yes Cross Current Protection: Yes Ground Fault Protection: Yes Short Circuit Protection: Yes Compatible Logic Voltage: 3.3V and 5V Five Step Modes: Full, 1/2, 1/4, 1/8 and 1/16 Mix with slow current attenuation model. Internal UVLO and low RDS (on) output. Automatic current attenuation mode Detection/Select. Phase-in rectifier, low power consumption. Warning: Connecting or disconnecting stepping motor while driver is powered on might damage driver. 4pcs Heat Sinks: 8 x 8mm / 0.31 x 0.31" Included: 1 x cnc shield v3 4 x A4988 4 x Hea

1.DLC runs GRBL open source firmware 2.Support SD card extender 3.Available to adjust the power, movement speed and engraving speed 4.uper grayscale carving function 5.Support Machine Structure is CNC, Laser-engraving machine, writing robot 6.Recommended Software is GRBL Controller, Benbox, mDraw Specification: Product name: DLC main control board Colour: Black Product material: ABS + metal Input voltage: DC12V Microprocessor:MEGA328P Motherboard size: 90 x 70mm Product weight: about 63g Package Contents: 1 x DLC Control Board 1 x USB Data CableOnly the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1

(1) Tấm chắn CNC khắc Phiên bản: 3.0 Màu đỏ Kích thước (L * W * H): 68 x 53 x 18 mm Điện áp: DC 12 ~ 36 V (Hiện tại chỉ có trình điều khiển DRV8825 có thể xử lý tối đa 36V nên vui lòng xem xét điện áp hoạt động khi cấp nguồn cho bo mạch.) Đặc trưng: 1.Sử dụng trình điều khiển bước tương thích A4988 hoặc DRV8825 có thể tháo rời. 2.Bảng mở rộng có thể được sử dụng cho máy khắc, bảng mở rộng trình điều khiển máy in 3 d 3.GRBL 0.8 tương thích. (Phần mềm nguồn mở chạy trên một cho UNO biến các lệnh mã G thành tín hiệu bước) 4.PWM Spindle và chân hướng, hỗ trợ 4 trục (X, Y, Z, A-Có thể sao chép X, Y, Z hoặc tạo một trục thứ 4 đầy đủ với phần sụn tùy chỉnh bằng cách sử dụng chân D12 và D13) 5. thiết kế nhỏ gọn. Động cơ bước có thể được kết nối với đầu nối molex 4 chân hoặc hàn tại chỗ. 6.Xin lưu ý rằng đây là một bộ chưa lắp ráp và cần có các kỹ năng hàn cơ bản. (2) Trình điều khiển động cơ bước A4988 Màu đỏ Kích thước (L * W * H): 20 x 15 x 10 mm Mạch ngắt nhiệt: Có Bảo vệ chéo dòng: Có Bảo vệ sự cố nối đất: Có Bảo vệ ngắn mạch tải: Có Nguồn cung cấp logic tương thích: 3,3V và 5 V Năm chế độ bước có thể lựa chọn: đầy đủ, 1/2, 1/4, 1/8 và 1/16 Đặc trưng: 1.Mix với các chế độ phân rã hiện tại chậm. 2.Internal UVLO và Ngõ ra RDS (Bật) thấp. 3. phát hiện / lựa chọn chế độ phân rã dòng điện tự động. 4. chỉnh lưu đồng bộ để tiêu tán công suất thấp. 5. Cảnh báo: Kết nối hoặc ngắt kết nối động cơ bước trong khi trình điều khiển được cấp điện có thể phá hủy trình điều khiển. (3) cho Ban ar-du-ino R3 MCU: ATmega328 Tốc độ đồng hồ: 16 MHz Giao diện USB: ATmega16U2 Điện áp hoạt động: 5 V Dòng đầu ra chân I-I / O: tối đa 40 mA Dòng đầu ra 3,3 V: tối đa 150 mA Chân I / O kỹ thuật số: 14 (bao gồm 6 chân với khả năng PWM) Chân đầu vào tương tự: 6 EEPROM: 1 kB RAM tĩnh (SRAM): 2 kB Bộ nhớ flash: 32 kB Kích thước (L * W * H): 68 x 53 x 10 mm gói bao gồm: 1 x Bảng UNO R3 1 x Tấm chắn CNC khắc 4 x Trình điều khiển động cơ bước A4988 1 x Kim hàng 40 chân 1 x cáp Ghi chú: Đo thủ công, xin vui lòng cho phép lỗi 1 ~ 3 cm, cảm ơn

Aibecy 3D Printer Accessories CNC Shield UNO-R3 Board A4988 Driver Kit With Heat Sink For Arduino Engraver 3D Printer Features: CNC shield uses removable A4988 or DRV8825 compatible stepper drivers; the CNC shield extension board can be used for carving machine, 3D printer driver expansion board. GRBL 0.8 compatible. (Open source firmware that runs on an Arduino-UNO that turns G-code commands into stepper signals); PWM Spindle and direction pins,4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13). Small size and compact design, Stepper Motors can be connected with 4 pin molex connectors or soldered in place. A4988 Stepper Motor Driver mixes with slow current decay modes; internal UVLO and low RDS (on) output. Automatic current decay mode detection/selection; synchronous rectification for low power dissipation. Specifications: CNC Shield Board -- Version: 3.0 Color: red Size: 6.8 * 5.3 * 1.8cm / 2.68 * 2.09 * 0.71in VoltageL DC 12-36V (at the moment only the DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.) A4988 Stepper Motor Driver -- Color: red Size: 2 * 1.5 * 1cm / 0.79 * 0.59 * 0.39in Thermal Shutdown Circuitry: yes Crossover Fault Protection: yes Load Short-Circuit Protection: yes Compatible Logic Suppluy: 3.3V and 5V Five Selection Step Modes:full, 1/2, 1/4, 1/8, 1/16 UNO R3 -- Color: blue Size: 6.8 * 5.3cm / 2.68 * 2.09in Package Size: 15 * 11 * 4cm / 5.9 * 4.33 * 1.57in Package Weight: 90g / 3.17oz Note: This is an unassembled kit and Basic soldering skills are needed. Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. Package List: 1 * UNO-R3 Board 1 * CNC Shield Board 4 * A4988 Stepper Motor Driver 4 * Heat Sink 1 * USB Cable 1 * 40-Pin Row Needles #cncshieldboard #3dprinteraccessorie #ConsumerElectronics #3dprinterkitreprap #a4988drv8825 #controller #Printers #unor3board #steppermotordriver #3dpr

Welcome to the [aurorawell] store Follow the store and enjoy the discount. Every week, creative new products are on the shelves. Selling is not the end, but the beginning of the promise! [Before ordering] Please read the dimensions and other related content carefully before purchasing. [shipment precautions] ✎The actual product is the same as the image displayed on the page. Shipped within 24 hours after delivery ✎ Normally, transportation takes 15-20 working days. ✎ Shipping costs are automatically displayed by the shopee system. Please contact the owner if you have any questions. I wish you a happy shopping! _______________❀Product Details❀_______ Features: CNC V3 Board: Detachable A4988 compatible stepper drive. The expansion board can be used for the engraving machine and the 3 d printer driver expansion board. GRBL 0.8 compatible. Open source firmware running for Arduino UNO, converting G code commands to step signals. PWM spindle and direction pins, 4-axis support (X, Y, Z, A- can copy X, Y, Z or make a complete 4th axis, using custom firmware, using pins D12 and D13). Compact design. The stepper motor can be connected or soldered into place with a 4-pin molex connector. Please note that this is an unassembled kit that requires basic welding skills. A4988 Stepper Motor Driver: A mixer with a slow current decay mode. Internal UVLO and low RDS (on) output. Automatic current decay mode detection/selection. Synchronous rectification, low power consumption. Warning: Connecting or disconnecting the stepper motor while the drive is powered may damage the drive. Specifications: CNC V3 Board: Color: Red Voltage: DC 12~36 V (At this time, only the DRV8825 driver can handle voltages up to 36V, so please consider the operating voltage when powering the board.) A4988 Stepper Motor Driver: Color: Red Thermal shutdown circuit: yes Cross current protection: yes Ground fault protection: yes Load short circuit protection: yes Compatible logic supplies: 3.3V and 5 V UNO R3 Board: Single chip microcomputer: ATmega328 Clock speed: 16 MHz USB interface: ATmega16U2 Operating voltage: 5 V I-I / O pin output current: up to 40 mA 3.3 V output current: up to 150 mA Digital I/O pins: 14 (including 6 PWM-capable pins) Analog input pin: 6 EEPROM: 1 kB Static RAM (SRAM): 2 kB Flash: 32 kB Package List: 1 * UNO R3 Board 1 * CNC Shield V3 Expansion Board 4 * A4988 Stepper Motor Driver 1 * 40-way Pin 1 * USB Ca

Specification: The extension board can be used for engraving machine or 3D printer driver. Compatible with GRBL 0.8. open-source firmware operated on Arduino UNO, converting G code command into stepping signal. PWM spindle and direction pin, 4 shaft support (X, Y, Z, A - you can copy X, Y, Z or use pin D12 and D13 customize firmware perform complete shaft 4). Compact design, stepping motor can connect 4 pin connectors or be soldered. This is a set of disassembled part, and you need basic soldering skills to solder them together. With high quality and durable performance. Feature: 100% brand new and in good condition. Color: As pictures show Heat sink dimension: about 8 * 8mm Version: V3.0 Voltage: DC 12V-36V(only DRV8825 driver can handle up to 36V, so please consider voltage for power supply) Board dimension: about 50*30*5mm Package Included: 1 x V3 Extension Board #V3CNCShield #3DPrinter #shield #ExtensionBoard #Engraving #A4988DriverBoard #pcs/lot #Arduino #Gadgets&OtherElectronics #Mac

CNC Shield Board: Latest CNC Shield Version 3.0 for Arduino.GRBL 0.9 compatible. (Open source firmware that runs on an UNO for Arduino that turns G-code commands into stepper signals).PWM Spindle and direction pins.4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13).2 x End stops for each axis (6 in total) Coolant enable,Uses removable A4988 or DRV8825 compatible stepper drivers Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping ).Compact design.Stepper Motors can be connected with 4 pin molex connectors or soldered in place. Runs on 12-36V DC. (At the moment only the DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.),Please note that this is an unassembled kit and Basic soldering skills are needed.A4988 Stepper Motor Driver Board is a breakout board for Allegro's A4988 DMOS Micro-stepping Driver with Translator and Overcurrent Protection; please read the A4988 datasheet carefully before using this product. Low RDS (On) Output,Automatic current decay mode detection / selection,Mix with slow current decay modes.Synchronous rectification for low power dissipation,Internal UVLO.Crossover-current protection,3.3 and 5 V compatible logic supply,Thermal shutdown circuitry,Ground fault protection,Load short-circuit protection,Five selectable step modes: full, 1/2, 1/4, 1/8 and 1/16. Colour: Photo Color Material: PC+ metal Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. (More generally, rewiring anything while it is powered is asking for trouble). Note: Green or Red PCB Package Includes: 1 x CNC Shield Board 4 x A4988 Stepper Motor Driver 4 x Heat Sink Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different from thereal thing. The measurement allowed error is +/- 1

Aibecy 3D Printer Accessories CNC Shield R3 Board A4988 Driver Kit With Heat Sink For Engraver 3D Printer Features: CNC shield uses removable A4988 or DRV8825 compatible stepper drivers; the CNC shield extension board can be used for carving machine, 3D printer driver expansion board. GRBL 0.8 compatible. (Open source firmware that runs on an board that turns G-code commands into stepper signals); PWM Spindle and direction pins,4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13). Small size and compact design, Stepper Motors can be connected with 4 pin molex connectors or soldered in place. A4988 Stepper Motor Driver mixes with slow current decay modes; internal UVLO and low RDS (on) output. Automatic current decay mode detection/selection; synchronous rectification for low power dissipation. Specifications: CNC Shield Board -- Version: 3.0 Color: red Size: 6.8 * 5.3 * 1.8cm / 2.68 * 2.09 * 0.71in VoltageL DC 12-36V (at the moment only the DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.) A4988 Stepper Motor Driver -- Color: red Size: 2 * 1.5 * 1cm / 0.79 * 0.59 * 0.39in Thermal Shutdown Circuitry: yes Crossover Fault Protection: yes Load Short-Circuit Protection: yes Compatible Logic Suppluy: 3.3V and 5V Five Selection Step Modes:full, 1/2, 1/4, 1/8, 1/16 UNO R3 -- Color: blue Size: 6.8 * 5.3cm / 2.68 * 2.09in Package Size: 15 * 11 * 4cm / 5.9 * 4.33 * 1.57in Package Weight: 90g / 3.17oz Note: This is an unassembled kit and Basic soldering skills are needed. Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. Package List: 1 * R3 Board 1 * CNC Shield Board 4 * A4988 Stepper Motor Driver 4 * Heat Sink 1 * USB Cable 1 * 40-Pin Row Ne

Decription: Features: Use removable A4988 or DRV8825 compatible stepping driver. The extension board can be used for engraving machine or 3D printer driver. Compatible with GRBL 0.8. Open-source firmware operated on Arduino UNO, converting G code command into stepping signal. PWM spindle and direction pin, 4 shaft support (X, Y, Z, A - you can copy X, Y, Z or use pin D12 and D13 customize firmware perform complete shaft 4). Compact design, stepping motor can connect 4 pin connectors or be soldered. This is a set of disassembled part, and you need basic soldering skills to solder them together. CNC Expansion Board: Version: V3.0 Color: Green Size: 68 x 53 x 18mm / 2.67 x 2.08 x 0.7" Voltage: DC 12V to 36V (only DRV8825 driver can handle up to 36V, so please consider voltage for power supply) 4pcs A4988 Driver: Size: 20 x 15mm / 0.78 x 0.59" Thermal Shutdown Circuit: Yes Cross Current Protection: Yes Ground Fault Protection: Yes Short Circuit Protection: Yes Compatible Logic Voltage: 3.3V and 5V Five Step Modes: Full, 1/2, 1/4, 1/8 and 1/16 Mix with slow current attenuation model. Internal UVLO and low RDS (on) output. Automatic current attenuation mode Detection/Select. Phase-in rectifier, low power consumption. Warning: Connecting or disconnecting stepping motor while driver is powered on might damage driver. 4pcs Heat Sinks: Size: 8 x 8mm / 0.31 x 0.31" Included: 1 x cnc shield v3 4 x A4988 4 x Hea

💥 MÔ TẢ SẢN PHẨM: Tên sản phẩm: Đầu dò tâm phôi cơ 10mm. Tính năng: lớp phủ titan kháng từ. Tốc độ: 450 RPM 💥 Size: Đường kính đầu lớn: 10 mm Đường kính đầu nhỏ: 4 mm Chiều dài đầy đủ: 90 mm 💥 Ứng dụng của đầu dò sét phôi giúp xác định gốc phôi gia công cho máy phay CNC hay máy phay cơ có lắp thước hiển thị số để đảm bảo lập trình gia công cho máy được nhanh chóng, chính xác nhất đảm bảo hiệu quả hoạt động nhất là với các máy lập trình.. 💥 Đặc trưng của đò dò sét phôi – Công cụ sét cạnh phôi được làm từ thép gió bền và có tuổi thọ lâu dài. Độ chính xác cao, sai số thấp 0.005mm. – Nó có thể xác định chính xác vị trí tâm của phôi đang được gia công – Lò xo có thể thay thế, chống mài mòn và tĩnh điện. – Thích hợp cho máy phay và máy phay CNC hay Trung tâm gia công. – Hoạt động bằng cách khi đưa điểm cuối tiếp xúc với cạnh phôi, khi gần đến nơi cần di chuyển từng chút một đến khi chạm vào mặt cạnh. Khi cạnh vào cạnh phôi và vượt qua điểm va chạm thì đầu dò sẽ dịch chuyển khỏi vị trí và bắt đầu trượt và đây là vị trí tham chiếu. 💥 Một số lưu ý khí sử dụng. – Không sử dụng công cụ tìm cạnh để bẻ cong hoặc kéo nó một cách miễn cưỡng, nếu không sẽ ảnh hưởng đến độ chính xác; – Không dính chất lạ hoặc bụi trên bề mặt đầu trượt; – Khi đo, tốc độ không được vượt quá 600RPM; – Công cụ tìm cạnh bù không thích hợp để sử dụng trên máy ngang. Vui lòng liên hệ với chúng tôi để được tư vấn và hỗ trợ giải đáp VÂN TẬP - Chuyên cung cấp linh kiện công nghiệp tại Việt Nam 🌐 Website: https://vantap.vn/ 🚩 Fanpage: fb/linhkiencongnghiepvantap 📩Email: [email protected] ☎ Hotline: 0364.399.090 or 02226.599.090 🏚 Địa chỉ: Số 34 - Đường Lý Thái Tổ - Phường Ninh Xá - Thành phố Bắc Ninh - Tỉnh Bắc Ninh - Việt Nam -------------------------------------------------------

Mũi Router CNC AK47-2 Arden 6 x 30 mm Cốt 12.7 mm * Mô Tả Sản Phẩm : - Xuất Xứ             : Đài Loan. - Thương Hiệu     : ARDEN - Hàng Chính Hãng. - Mã Hiệu            : AK47-2 - 62006308 - Chất Liệu          : Thép hợp kim cứng. - Sử Dụng Cốt Máy Phay 12.7 mm. - Thiết Kế 3 Lưỡi Dao. - Kích Thước       : 6 x 30 mm ( Như Hình Vẽ ) - Đơn giá bán 1 Mũi. * Tính Năng Sản Phẩm : - Sản phẩm chuyên dụng kết hợp với máy CNC để ra phôi ván gỗ, nhựa, mica... - Chất lượng cao và tuổi thọ lâu dài hơn so các dòng mũi thông thường. - Thiết kế cắt ba lưỡi đồng tâm , khe thoát nhiệt cho khả năng làm việc độ chính xác trong môi trường làm việc cường độ cao. - Dòng mũi ARDEN được phủ 1 lớp TEFLON giúp tăng độ cứng, cho thời gian sử dụng và độ đúng tâm tốt hơn. #arden #CNC #muiCNC #daophay #muiphay #maycnc #cnc #mũi

Aibecy 3D Printer Accessories CNC Shield R3 Board A4988 Driver Kit With Heat Sink For Engraver 3D Printer Features: CNC shield uses removable A4988 or DRV8825 compatible stepper drivers; the CNC shield extension board can be used for carving machine, 3D printer driver expansion board. GRBL 0.8 compatible. (Open source firmware that runs on an board that turns G-code commands into stepper signals); PWM Spindle and direction pins,4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13). Small size and compact design, Stepper Motors can be connected with 4 pin molex connectors or soldered in place. A4988 Stepper Motor Driver mixes with slow current decay modes; internal UVLO and low RDS (on) output. Automatic current decay mode detection/selection; synchronous rectification for low power dissipation. Specifications: CNC Shield Board -- Version: 3.0 Color: red Size: 6.8 * 5.3 * 1.8cm / 2.68 * 2.09 * 0.71in VoltageL DC 12-36V (at the moment only the DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.) A4988 Stepper Motor Driver -- Color: red Size: 2 * 1.5 * 1cm / 0.79 * 0.59 * 0.39in Thermal Shutdown Circuitry: yes Crossover Fault Protection: yes Load Short-Circuit Protection: yes Compatible Logic Suppluy: 3.3V and 5V Five Selection Step Modes:full, 1/2, 1/4, 1/8, 1/16 R3 Board-- Color: blue Size: 6.8 * 5.3cm / 2.68 * 2.09in Package Size: 15 * 11 * 4cm / 5.9 * 4.33 * 1.57in Package Weight: 90g / 3.17oz Note: This is an unassembled kit and Basic soldering skills are needed. Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. Package List: 1 * R3 Board 1 * CNC Shield Board 4 * A4988 Stepper Motor Driver 4 * Heat Sink 1 * USB Cable 1 * 40-Pin Row Needles #cncshieldboard #a4988steppermotordriver #a4988driverkit #3dprinterparts3dprinteraccessoriestlsmootheraddonmoduletlsmootheraddonmoduletlsmootherforpatterneliminationmotorfor3dprintermotordrivers4pcstlsmootherv10addonmoduletlsmootherplusfora4988anddvr8825 #3dprinterpart #heatsink #unor3board #3dprinteraccessorie #steppermotornema17steppermotordriverservomotorsteppermotornema17inductionmotornema17steppermotorsteppermotormotorsteppermotornema17nema173dprintertwophase4wiresteppermotorfor18degnema17stepper

We have many products in our warehouse, our warehouse is in Shenzhen . Genaral it need 1-2weeks arrive your hand. if you subimit order , we will handle in 1-3days.if you chat with us , we donot reply you, donot worry , we are try to handle your order.so pls donot cancel o

___________________❀Alwaysonline❀___________________ Welcome to our store, we insist on the lowest price to sell the best quality items. ✔Ready Stock ✔Wholesale Price ✔Quality Checked ★Surprises for you★ ☞Shop Voucher: Get More Discount ☞Follow Shop: Free Gifts ☞“Like” Items: Priority Shipping ( Sent us follow shop screenshot and remark on your order "Free Gift", if not will miss) ★★Attention Please★★ ✌We will be based on your guests in your country to send the corresponding adapter plug. _______________❀Product Information❀______________ Features: CNC V3 Board: Detachable A4988 compatible stepper drive. The expansion board can be used for the engraving machine and the 3 d printer driver expansion board. GRBL 0.8 compatible. Open source firmware running for Arduino UNO, converting G code commands to step signals. PWM spindle and direction pins, 4-axis support (X, Y, Z, A- can copy X, Y, Z or make a complete 4th axis, using custom firmware, using pins D12 and D13). Compact design. The stepper motor can be connected or soldered into place with a 4-pin molex connector. Please note that this is an unassembled kit that requires basic welding skills. A4988 Stepper Motor Driver: A mixer with a slow current decay mode. Internal UVLO and low RDS (on) output. Automatic current decay mode detection/selection. Synchronous rectification, low power consumption. Warning: Connecting or disconnecting the stepper motor while the drive is powered may damage the drive. Specifications: CNC V3 Board: Color: Red Voltage: DC 12~36 V (At this time, only the DRV8825 driver can handle voltages up to 36V, so please consider the operating voltage when powering the board.) A4988 Stepper Motor Driver: Color: Red Thermal shutdown circuit: yes Cross current protection: yes Ground fault protection: yes Load short circuit protection: yes Compatible logic supplies: 3.3V and 5 V UNO R3 Board: Single chip microcomputer: ATmega328 Clock speed: 16 MHz USB interface: ATmega16U2 Operating voltage: 5 V I-I / O pin output current: up to 40 mA 3.3 V output current: up to 150 mA Digital I/O pins: 14 (including 6 PWM-capable pins) Analog input pin: 6 EEPROM: 1 kB Static RAM (SRAM): 2 kB Flash: 32 kB Package List: 1 * UNO R3 Board 1 * CNC Shield V3 Expansion Board 4 * A4988 Stepper Motor Driver 1 * 40-way Pin 1 * USB Ca

5 trục CNC Breakout Shield Board Trình điều khiển động cơ bước Bộ điều khiển mô-đun MACH3 Features: 1.Fully support MACH3 and other computer software that support parallel port control. 2.USB power supply and peripherals powered phase separation to protect computer security. 3.Peripheral wide voltage input, 12-24V, and anti-reverse function. 4.All input signal are optocoupler isolated, which can urgently stop, limit, to protect computer security. 5.All the way to the relay output port,spindle switch controllable. Output port is P17. Descriptions: 1.All the way through the optocoupler isolated 0-10V analog voltage output can be controlled with the corresponding analog interface converter to control the spindle speed. Output port is P1. 2.Open all 17 ports, which can be accessed with the optocoupler drive, 5-axis stepper motor can be controlled. 3.P1 as PWM outputs can be controlled with optocoupler input spindle governor. Can be accessed by a common cathode or common anode input level to 5V drive. Specifications: Color:blue Model:MACH3 Peripheral voltage input:12-24V Package Information: Package size:98 x 70 x 25mm/3.86 x 2.76 x 0.98in Package Weight:45g/1.59oz Poly Bag Package Package Included: 1 x 5 axis CNC Breakout Board 1 x USB C

Features: Each Road stepper motors only need two IO ports This expansion board as a driver expansion board, can be used for engraving machines, 3D printers. PWM Spindle and direction pins. 4-Axis support. Runs on 12-36V DC It is a total of four slots, can drive four A4988 stepper motor. Each road stepper motors only need two IO ports. Specifications: Color:As picture Quantity:1PC Package Include:1PC Expansion Board Note: 1.Please allow 0.1-0.3cm differences due to manual measurement, thanks. 2.Please understand because of the light irradiation or computer display difference, so I can't guarantee photos and real color is 100% the